Subscribe to Our Youtube Channel
Summary of Contents for LTC RVC7020
- Page 1 Model No.: RVC7020 Trådlös Back-kamera och Monitor Instruktions manual Viktigt: Läs igenom manualen noga före användning och spara den för framtida bruk.
- Page 2 Bä ste Kund, Din RVC7020 trådlö s back-kamera och monitor kommer att underlä tta fö r dig som fö rare nä r du vill se bakom din bil, lastbil, husvagn, husbil m.m. Vi hoppas att ni kommer få mycket nytta av produkten.
-
Page 3: Installation
9. AV-kabel Hä ftande tejp Installation Fö ljande instruktioner ä r generella och gä ller ej på alla stä llen RVC7020 monteras på . Om ni stö ter på problem vid montering kontakta service@lejontrading.se. INSTALLATION AV MONITOR Nä r platsen fö r montering av monitorn skall bestä mmas, var noga med att ej montera den i synfä... - Page 4 B. Solskydd- och nackstö ds-montering 1. Anvä nd de 2 remmarna och spä nn fast dem på baksidan av monitorn. 2. Placera monitorn antingen på solskyddet eller på nackstö det. 3. Snurra remmarna runt solskyddet eller nackskyddet. 4. Spä nn remmarna fö r att stabilisera monitorn. Notera: Under extremt ljus, kan det hä...
- Page 5 KAMERAINSTALLATION Kameran kan monteras ovanfö r eller under registreringsskylten med skruv eller bult. Se till så att kameran ej dö ljs av nå gon utstickande detalj på fordonet. Anvä nd medfö ljande vinklar fö r att justera in rä tt vinkel på kameran. 1.
- Page 6 10.Nä r det ä r konstaterat vilket som ä r + och -, stä ng av tä ndningen, avlä gsna sedan minuskabeln frå n batteriet. 11.Anvä nd de medfö ljande kabel delarna fö r att koppla in + kabeln till backljusets + kabel. 12.Anvä...
- Page 7 MONITOR–KNAPPAR The monitor will automatically turn ON when the vehicle is in reverse gear. Also, there are 6 control buttons available for user controls. Monitorn kommer automatiskt att gå igå ng nä r man lä gger i backen. Dä r finns 6 knappar som du styr monitorn med.
-
Page 8: Tekniska Specifikationer
Riktlinjer På /AV Tryck på riktlinjer PÅ/AV fö r att skifta mellan att ha riktlinjer PÅ eller AV på skä rmen. Tekniska specifikationer Nominal Grä ns Enhet Beskrivning Test vä rde Vä rde Kamera(Sä ndare) Strö m fö rsö rjning Likströ... - Page 9 TESTA SYSTEMET 1. Kontrollera så att minuskabeln till batteriet ä r ordentligt fastsatt. 2. Vrid bilnyckeln till ACC, starta ej motorn. 3. Drag å t parkeringsbromsen, lä gg vä xeln i back. 4. Nu kommer en bild att visas på monitorn. Stä mmer ej bilden med backspegeln, tryck då på spegelvä...
- Page 10 Model No.: RVC7020 Wireless Back-Up Camera and Monitor OWNER’S MANUAL IMPORTANT: READ THESE INSTRUCTIONS BEFORE USE AND RETAIN FOR FUTURE REFERENCE.
- Page 11 Dear Customer, CONGRATULATIONS. The RVC7020 Wireless Back-up Camera and Monitor, when used as described, will improve your ability to see behind your car, truck, RV, or mini-van. We have taken numerous measures in quality control to ensure that your product arrives in top condition, and will perform to your satisfaction.
-
Page 12: Monitor Installation
7. Dashboard Stand & Double 8. Monitor Mounting Belts 9. AV Cable Sticky Back Base Installation These instructions do not apply to all vehicles. They are only meant as a general guide due to the number of different makes & models. For vehicle specific questions contact your vehicle’s manufacturer. - Page 13 B. Visor and Headrest Mount 1. Use the supplied two belts to pass through the recesses at the back of the monitor unit. 2. Locate the monitor on the visor or headrest. 3. Pass the belts across the visor or headrest. 4.
-
Page 14: Camera Installation
CAMERA INSTALLATION You can mount the camera using the top or bottom mounting bolts or screws of license plate. Ensure the camera viewing is not obstructed. The supplied wedge shaped spacers can adjust the camera mounting angle vertically. 1. Loosen the license plate bolts or screws and remove the rear license plate. 2. - Page 15 23.Once you have located the reverse light circuit, you need to route the power cable supplied to that location. Fasten the power cable securely to prevent it from being caught on any vehicle component like the trunk hinge. Never route the cable on the outside of the vehicle. 24.Locate reverse light socket and remove light bulb.
-
Page 16: Monitor Controls
MONITOR CONTROLS The monitor will automatically turn ON when the vehicle is in reverse gear. Also, there are 6 control buttons available for user controls. Power On/Off Button - BLUE LED Power Indicator Press POWER ON/OFF button to supply power to monitor. When monitor image is ON, the blue LED will be lit. -
Page 17: Technical Specification
AV/CH Mode To enable or disable the automatically switching from AV/CH input to Back Up Camera view, press MENU button until BACK UP is selected. Then press + or – repeatedly, then turn it to AUTO or MANUAL mode. When it is under AUTO mode, it will be Audio/Video Input view when the vehicle is not in reverse gear;... - Page 18 Operation Temperature -10 to + 60 Storage Temperature -20 to + 80 monitor Power Operation Voltage (battery operate ) DC POWER SUPPLY 10-15 Operation Current [Min] Power/off Operation Current [Min] with LCD off < 170 with LCD on, picture display With Operation Current [Max] speaker max, output LCD display screen size...
-
Page 19: Testing The System
TESTING THE SYSTEM 6. Reattach the vehicle’s negative battery cable. 7. Turn the ignition key to the accessory position, do not start the vehicle. 8. Engage the parking brake, put the shifter in the reverse position. 9. Look at the monitor, if the image does not match your rear view mirror press the Menu button and Direction setting on the monitor to correct the image.
Need help?
Do you have a question about the RVC7020 and is the answer not in the manual?
Questions and answers