1. Manuals
  2. Brands
  3. Astrohog Manuals
  4. IP Phone
  5. IP0032
  6. Manual

Astrohog IP0032 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
IP Phone Manual
Contents
1. Introduction
1.1
Hardware Overview
1.2
2.1
2.2
2.3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
Page
1
1
2
3
3
3
4
8
8
9
10
12
19
24
30
30
32
32
33
34
IP Phone Manual
DESCRIPTION
20 21
19
18
17
16
15
14
13
12
11
1.
LCD
2.
OK
3.
PHBOOK
4.
MENU/ESC
5.
VOL +
6.
VOL -
7.
NUMBER KEY
8.
REDIAL
9.
H.F
10. H.F MIC
11. CALL IN
12. CALL OUT
1. Introduction
This user's manual is for VoIP Phone with FXO interface. This user's manual will explain
the keypad instruction, web configuration and command line configuration for the VoIP
Phone. Before using the VoIP Phone, some setup processes are required to make the
VoIP Phone work properly. Please refer to the Setup Menu for further information.
1.1 Hardware Overview
The VoIP Phone has the following interfaces for Networking, telephone interface, and
power connector.
22
23
1
2
3
4
5
6
7
8
9
10
13. CONF
14. FLASH
15. HOLD
16. POWER
17. UP/DEL
18. DOWN
19. HANDSET
20. PSTN
21. WAN
22. LAN
23. DC7.5V
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IP0032 and is the answer not in the manual?

Questions and answers

Summary of Contents for Astrohog IP0032

  • Page 1: Table Of Contents

    IP Phone Manual IP Phone Manual Contents Page DESCRIPTION 20 21 1. Introduction Hardware Overview Software Overview 2. Keypad interface for IP Phone demo system Keypad description IP or PSTN Keypad Function and setting List 3. Setup the VoIP Phone by Web Browser Login System Information for the VOIP PHONE Phone Book...

  • Page 2: Software Overview

    IP Phone Manual IP Phone Manual SIP Server Firmware Upgrade Two RJ-45 Networking interface, these two interfaces support 10/100Mps Fast Ethernet. Registrar Server TFTP you can connect one RJ-45 Fast Ethernet port to the ADSL or Switch, and connect the (three SIP account) Console other one to your computer.

  • Page 3: Keypad Function And Setting List

    IP Phone Manual IP Phone Manual SNTP: Enabled / Disable SNTP. 2.3 Keypad Function and setting List Primary SNTP: Set Primary SNTP server IP address. Secondary SNTP: Set Secondary SNTP server IP address. Phone Book Time zone: Set Time zone. Search: Search Phone Book.
  • Page 4 IP Phone Manual IP Phone Manual PPPoE setting Proxy server Proxy: SIP Proxy server address setting User name: PPPoE user name setting Domain server: Domain server address setting Password: PPPoE Password setting Outbound proxy: Outbound Proxy address setting LAN Setup Bridge: set Ethernet interface into bridge mode Third realm NAT: set Ethernet interface into NAT mode...

  • Page 5: Setup The Voip Phone By Web Browser

    IP Phone Manual IP Phone Manual NAT Transversal 2. Click the Login button will move into the VOIP PHONE web based management information page. STUN setting 3. If you change the setting in the Web Management interface, please do remember STUN: STUN disabled/enabled to click the Submit button in that page.

  • Page 6: Phone Book

    IP Phone Manual IP Phone Manual 3.3 Phone Book 3. In Speed Dial setting function you can add/delete Speed Dial number. You can 1. In Phone Book contains Phone Book and Speed Dial Settings. You can setup the input maximum 10 entries speed dial list. Phone Book and Speed Dial number.

  • Page 7: Phone Setting

    IP Phone Manual IP Phone Manual 3.4 Phone Setting SNTP Setting function: you can setup the primary and second SNTP Server In Phone Setting contains Call Forward, SNTP Settings, Volume Settings, Block IP Address, to get the date/time information. Also you can base on your Setting, Caller ID, Auto Dial Setting, Dial Plan, Flash Time Setting, Call Waiting location to set the Time Zone, and how long need to synchronize again.
  • Page 8 IP Phone Manual IP Phone Manual Block Setting function: you can setup the Block Setting to keep the phone slience. You can choose Always Block or Block a period. Always Block: All incoming call will be blocked until disable this feature. Block Period: Set a time period and the phone will be blocked during the time period.
  • Page 9 IP Phone Manual IP Phone Manual Symbol explan: 0,1,2,3,4,5,6,7,8,9 x or X Replace rule: If replace prefix code is ON and prefix number is matched with rule then 005 will replace prefix. Auto Dial Time: Stop dialing after seconds then send dial number out. Dial Plan: When match with pattern then send dial number out but if fisrt digit is 0 then dial plan will be ignored.

  • Page 10: Network

    IP Phone Manual IP Phone Manual 3.5 Network Call Waiting Setting function: If user doesn't want to be inform there is a new In Network you can check the Network status, configure the WAN Settings, LAN incoming call, user can set the function off. When you finished the setting, please Settings, DDNS settings and VLAN Settings.
  • Page 11 IP Phone Manual IP Phone Manual The IP Phone's default setting is NAT mode. If you don't need to use the NAT LAN Settings: In this page you can configure the IP Phone LAN port's setting. Mode, you can chang to Bridge Mode. If you change the setting to Bridge The LAN port's default IP address is 192.168.123.1, Net Mask is 255.255.255.
  • Page 12 IP Phone Manual IP Phone Manual DDNS Setting: You can configure the DDNS setting in this page. You need to have VLAN Setting: You can set the VLAN setting in this page. There are two parts in the DDNS account and input the informations properly. You can have a DDNS acc- this page.

  • Page 13: Sip Settings

    IP Phone Manual IP Phone Manual You can see the Register Status in the Status item. If the item shows Registered, then your VoIP Phone is registered to the ISP, you can make a phone call direcly. If you have more than one SIP account, you can following the steps to register to the other ISP.
  • Page 14 IP Phone Manual IP Phone Manual Port Settings: you can setup the SIP and RTP port number in this page. Each ISP provider will have different SIP/RTP port setting, please refer to the ISP to setup the port number correctly. When you finished the setting, please click the Submit button.
  • Page 15 IP Phone Manual IP Phone Manual Other Settings: you can setup the Hold by RFC, Voice/SIP QoS and SIP expire time in this page. To change these settings please following your ISP information. When DTMF Setting: you can setup the RFC2833 Out-Band DTMF , Inband DTMF and you finished the setting, please click the Submit button.

  • Page 16: Nat Trans

    IP Phone Manual IP Phone Manual 3.7 NAT Trans In NAT Trans. you can setup STUN function. These functions can help your VoIP Phone working properly behind NAT. STUN Setting: you can setup the STUN Enable/Disable and STUN Server IP addre- ss in this page.

  • Page 17: System Auth

    IP Phone Manual IP Phone Manual 3.11 Update In Update you can update the VoIP Phone's firmware to the new one or do the factory reset to let the VoIP Phone back to default setting. In New Firmware function you can update new firmware via HTTP in this page. You can ugrade the firmware by the following steps: Select the firmware code type, Risc or DSP code.

  • Page 18: Reboot

    IP Phone Manual 3.12 Reboot Reboot function you can restart the VoIP Phone. If you want to restart the VoIP Phone, you can just click the Reboot button, then the VoIP Phone will automatically.

Table of Contents