FLIR Raymarine Raymic Series Installation Instructions

RaymafHH
Raymic
60/70
Handset installation
instructions
Powering on the handset
The Raymic
60/70 handset accessory
can
be connected to the
Ray60 and Ray70
radios.
The Handset must be switched on using the Handset's Power
button.
With
the
Handset connected to
the
Base station:
7.
OK / menu button
-
Press button to access menu
/
DSC
functions and to confirm selections.
8.
16
/ PLUS
-
When powered on press to switch
between
priority channels.
9.
HI/LO
-
Press to switch between High (25 W)and
low
(1
W) transmit power.
10. DISTRESS
-
Lift up
the
spring loaded cover and
press this
button to make a DSC distress
call.
1
1
.
Channel
Up
and Down
-
Changes the channel up or down.
12. VOL/SQ
-
Press button to switch between volume
and
squelch control.
13.
Built-in
speaker
Second handset station
-
Ray60 /
Ray70
The Raymic handset accessory can
be connected to the second
station connector located on the rear of the radio, this will create
a second fully
functional
station.
1.
Primary station.
2.
Raymic handset
extension cable (480290, A80291
or
480292)
3.
Raymic handset second station
(480289)
4.
Panel mount fixings kit (R70438)
5.
Raymic handset adaptor cable with RCA audio
(480297)
6.
Primary station
passive speaker
7.
Second
station passive speaker
Note:
As
the
Fistmic
does
not include a display it cannot be
used to create a second functional station.
Alarm behavior for second station passive
speakers
The
480297 adaptor cable can be used on the Ray60 and Ray70
Radios
to
connect an
additional
passive speaker to
the second
station. A
passive speaker connected to the
second station will
only
receive
voice audio.
Alarms
will
NOT be heard
from
the
passive speaker when it is connected to the second station.
Handset extension cables
Handset station cabling can be extended using approved
extension
cables.
The maximum
length
of
cable
from the
Handset
to the
Base
station
should
not exceed
50 m (164 ft)
2.
1.
Press the Power button.
The
Handset
will
switch on.
To switch
the Handset off, press and
hold
the Power
button
for
approximately 3 seconds.
Ray60
/ Ray70 handset controls
The optional
handset
for the Ray60 and Ray70 VHF radios
includes the
following
controls:
1.
Power
-
Press to
power
the handset
on.
Press and
hold
for 3 seconds to
power
the handset
off. Momentary press to
access the shortcut list.
2.
PTT
(Push to Talk)
-
Press and hold to send a voice
message.
Release
to return to receive
mode"
Note:
The maximum transmit
time is limited to 5 minutes
to
prevent un-intentional transmissions from
occupying
the
VHF
channel.
3.
Microphone location
4.
Volume
Up
and Down
-
Press
to
adjust volume or squelch
up and down.
5.
LCD
6.
Back
-
Move back through menu options.
Document number: 88064-'l
llLatUE+l--o
l'[sl.
I
lFl=l=?-
|
u;;r
fii--:l::-llJ
\i\
=l: ,r/
v
\\\t-t--r7
\l=t.-/
6)
v
(,
Date:03-2016