1. Manuals
  2. Brands
  3. Acuity Brands Manuals
  4. Electronic dictionary
  5. eldoLED SC 4202/L
  6. Quick start manual

Acuity Brands eldoLED SC 4202/L Quick Start Manual

Hide thumbs
1
2
3
4
5
6
Table of Contents

Advertisement

Quick Links

Download this manual

Safety

Before installing or performing routine maintenance upon this equipment, follow the general precautions listed in this section.
WARNING: RISK OF ELECTRIC SHOCK
-
May result in serious injury or death. Disconnect or turn off power before installation or maintenance.
-
The device may only be connected and installed by a qualified electrician. All applicable regulations,
legislation and building codes must be observed. Incorrect installation of the device can cause
irreparable damage to the device and the connected LEDs.
-
Verify that supply voltage is correct by comparing it with the product information.
-
Make all electrical and grounded connections in accordance with all applicable local code
requirements.
WARNING: RISK OF BURN OR FIRE
-
Do not exceed maximum wattage, ratings, or published operating conditions of product.
-
Do not overload.
-
Follow all manufacturer's warnings, recommendations and restrictions to ensure proper operation of
product.
CAUTION: RISK OF DAMAGE DUE TO ESD
-
Electrostatic Discharge (ESD) can damage product(s). Personal grounding equipment must be worn
during all installation of the unit.
-
Do not touch individual electrical components as this can cause ESD and affect product performance.
CAUTION: RISK OF PRODUCT DAMAGE
-
Pay attention when connecting the LEDs: polarity reversal results in no light output and often
damages the LEDs.
-
Do not stretch or use cable sets that are too short or are of insufficient length.
-
Do not tamper with contacts.
-
Do not modify the product.
-
Do not change or alter internal wiring or installation circuitry.
-
Do not use product for anything other than its intended use.
-
Do not install damaged product! This product has been properly packed so that no parts should have
been damaged during transit. Inspect to confirm.
© 2018 eldoLED. All rights reserved. V1.1 All content contained herein is subject to change without prior notice.
More product documentation and eldoLED´s terms and conditions are available at www.eldoLED.com
Quick Start Guide
SC 4202/L

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the eldoLED SC 4202/L and is the answer not in the manual?

Questions and answers

Summary of Contents for Acuity Brands eldoLED SC 4202/L

  • Page 1 Quick Start Guide SC 4202/L Safety Before installing or performing routine maintenance upon this equipment, follow the general precautions listed in this section. WARNING: RISK OF ELECTRIC SHOCK May result in serious injury or death. Disconnect or turn off power before installation or maintenance. The device may only be connected and installed by a qualified electrician.
  • Page 2 Quick Start Guide SC 4202/L SC 4202/L: a 0-10V to DALI translator The SC 4202/L translates 0-10V control signals into a DALI signal for the LightShape-enabled eldoLED DUALdrive. The device is intended for indoor use, to be installed completely enclosed within the end user listed enclosure in accordance with the manufacturer installation instructions and in compliance with NEC.
  • Page 3 Quick Start Guide SC 4202/L Wiring Diagrams General wiring diagram Select a 0-10V controller with a full voltage range. We recommend that you test your controller’s full voltage input range into the translator. The recommended Sensor Switch controller compatible with the SC 4202/L translator is the sPODMRD EZ. Ensure the controller’s maximum sink current is 50mA.
  • Page 4 Quick Start Guide SC 4202/L Wiring diagram for pendant linear applications with remote enclosure Wiring diagram for installations greater than 15 LED drivers This type of application can have up to 30 translators. Each 0-10V input can source up to 1mA.
  • Page 5 Quick Start Guide SC 4202/L Resolution and dimming curve diagrams Intensity curve Color temperature path Resolution curve up to 256 dimming steps for intensity and color temperature...
  • Page 6 Quick Start Guide SC 4202/L Europe, Rest of World North America eldoLED B.V. eldoLED America Science Park Eindhoven 5125 One Lithonia Way 5692 ED Son Conyers, GA 30012 The Netherlands info@eldoled.com info@eldoled.com www.eldoled.com www.eldoled.com...

Table of Contents