Table of Contents
Advertisement
Quick Links
Instruction manual / Montageanleitung
SPECIFICATIONS
Wingspan:......................................1610mm
Length:...........................................1190mm
Electric Motor:.....................See next pager
Glow Engine:.................... .46 2-T / .70 4-T
RTF Weight: 3.2Kg (will vary with equipment
use)
Radio:....................7 Channel / 7 Servos
Function: Ailerons-Elevator-Rudder-Throttle
Flaps-Optional Retractable Landing Gear.
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and
cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,
die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen. Bei unsachgemässer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstätzung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
Radio Control Model / Flugmodell
ZLIN
Z-526 Akrobat
ALL BALSA, PLYWOOD CONSTRUCTION AND ALMOST READY TO FLY
TECHNISCHE DATEN
Spannweite:...................................1610mm
Lange:............................................1190mm
Elektroantrieb.............(siehe nächste Seite)
Verbrennerantrieb:...............7.45cc - 11.5cc
Fluggewicht:.......................................3.2Kg
Fernsteuerung..........7 Kanal / 7 Servos
Advertisement
Table of Contents
Summary of Contents for Zlin Aircraft Z-526 Akrobat
- Page 1 Radio Control Model / Flugmodell ZLIN Z-526 Akrobat ALL BALSA, PLYWOOD CONSTRUCTION AND ALMOST READY TO FLY Instruction manual / Montageanleitung TECHNISCHE DATEN SPECIFICATIONS Wingspan:........1610mm Spannweite:........1610mm Length:...........1190mm Lange:..........1190mm Electric Motor:.....See next pager Elektroantrieb.....(siehe nächste Seite) Glow Engine:.....46 2-T / .70 4-T Verbrennerantrieb:....7.45cc - 11.5cc...
- Page 2 Optional accessories. Please visit www.shop.pichler.de for more information Empfohlenes Sonderzubehör. Mehr Infos unter www.shop.pichler.de Extension cord for aileron servos: 50cm(x2) Extension cord for flap servos: 50cm(x4) Extension cord for retract servos: 30cm(x2) Extension cord for Rx battery pack: 20cm(x1) BOOST 50 Brushless Combo Set Standard Mini # C3173...
- Page 3 ZLIN 1- Aileron and Flap servo Z-526 Adhesive tape 1-Cut away the covering of the wing bottom -Switch on the radio (trims centered) where the aileron servo goes. Then mount the ailerons servo horn In neutral position. 2-Connect the aileron and flap servo cord to the -The servo horn should be extension cords.
- Page 4 ZLIN 4- Extension cord secured Z-526 Aileron extension cord Keep the aileron extension cord exit hole in place using sticker. WING - TOP VIEW cut away only the covering 5- E-retract - Strut installation 3x15mm screw ...4 / not include...
-
Page 5: Fixed Gear
ZLIN 6- Decor Z-526 2x6mm screw ...5 7- Fixed gear Square plastic 3x20mm Ply gear mount flat Nylon gear strap Gear mount 3x12mm screw Main landing gear ..8 3x20mm screw ..16 Ply gear mount Square plastic Gear mount x 2 Nylon gear strap plate x 2 ..4... - Page 6 ZLIN 8- Fixed gear Z-526 75mm whell ...x2 4mm collar...4 9- Joinning the wing halves Nylon wing bolt Rubber band (both the top and bottom) Binder clip Center line Top view Use epoxy glue to bury the opening 1- Using a pencil, mark the center of the brace. 2- Trial fit the wing joiner into one of the wing panels.
- Page 7 ZLIN 10- Engine Z-526 B=B’ B’ Pull the magnetic top hatch out of the fuselage. FRONT-VIEW - Using a pencil or felt tipped pen, mark the fire wall where the four holes are to be drilled ! Engine thrust on fire-wall ! Align the mark on both mounts is already adjust at factory with the mark on the fuselage...
- Page 8 ZLIN 11- Engine Z-526 - Reposition the engine on to the engine mounts so the distance from the prop hub to the fire wall is 132 to133mm. - Mark the engine mounting plate where the four holes are to be drilled. Note: Mark the mounting plate through the engine mounting flanges.
- Page 9 ZLIN 12- Fuel tank Z-526 Blow To muffler Water Filler tube Rubber stopper 3x25mm screw To engine 3x35 mm screw After confirming the direction . Insert this assembly, clunk end first, into the fuel Checking for leaks - block the vents and blow tank and tighten and screw the fuel tank cap on firmly.
- Page 10 ZLIN 14- Electric motor Z-526 -Using a aluminum motor mounting plate as a template, mark the plywood motor mounting plate where the four holes are to be drilled. -Remove the aluminum motor mounting plate and drill a 1/8”(3mm) hole through the plywood at each of the four marks marked .
-
Page 11: Electric Motor
ZLIN 15- Electric motor Z-526 - Position the motor on to the plywood motor mounting so the distance from the prop hub to the fire wall is 132 to133mm. - Secure the motor to the plywood motor mounting using the four 3x20mm screws. 132 - 133mm 3mm screw/nut...4 ! Engine thrust on fire-wall... - Page 12 ZLIN 17- Installing the bottom cover Z-526...
-
Page 13: Horizontal Stabilizer
ZLIN 18- Horizontal stabilizer Z-526 Using a sharp hobby knife, carefully cut away the covering around of all slots for the horizontal stabilizer and vertical fin installation. Pull the left and right elevator out of the horizontal stabilizer. Push the horizontal stabilizer into the slot on the fuselage as show. -
Page 14: Vertical Stabilizer
ZLIN 19- Horizontal stabilizer Z-526 Install the horizontal stabilizer onto the fuselage and adjust the alignment as described in steep 18B. Note: it is important to ensure that the horizontal stabilizer is also level in regards to the fuselage. Apply the thin CA along the area where the covering was removed in the previous step and to the fuselage where the horizontal stabilizer mounts . -
Page 15: Installing The Elevator
ZLIN 21- Vertical stabilizer Z-526 Remove the vertical stabilizer from the fuselage. Using s sharp hobby knife, carefully cut away the covering below the lines which were drawn in the Insert the vertical fin into the fuselage, precisely align previous steep. Do not cut into the woods as this the vertical stabilizer as described in step 20B. -
Page 16: Installing The Rudder - Control Horn
ZLIN 23- Elevator control horn Z-526 Push the elevator push-rod with clevis into the black nylon push-rod guide. Using the plastic control horn as a template, mark the mounting hole positions, where the Control horn Alignment elevator clevis meet the elevator control horn with a felt tipped or a pencil. - Page 17 ZLIN 25- tail wheel Z-526 - Insert the tail wheel push-rod into the hole on the tail gear control horn (as show). - Install the tail wheel control horn in place. - Instal the tail wheel gear in place. - Secure the tail wheel control horn in place using a 2mm screw set, ensure smooth non-binding movement.
- Page 18 ZLIN 27- Servo - linkages Z-526 Elevator pushrod 3mm set Screw Elevator pushrod D=5/64”(2mm) 2 mm Elevator servo FUSELAGE - BOTTOM VIEW Throttle rod 2 mm Throttle servo In case of Glow engine using (2 x120mm) rod ....2 (1.2 x500mm) throttle rod ....1 Connector ....2...
- Page 19 ZLIN 28- Decor Z-526 PREMIUM SE-KLB EXPERIMENTAL Note: Cut out the stickers and apply them in the proper area. EXPERIMENTAL Do not peel the backing paper off all at once. Peel off one corner of the backing and cut off with scissors. Arrange sticker on model and when satisfied adhere the corner without backing.
- Page 20 ZLIN 29- Decor Z-526 ZLIN 526 ASM HB-TRQ HB-TRQ HB-TRQ Sticker ZLIN 526 SWISS...
- Page 21 ZLIN 30- Decor Z-526 Note: Cut out the stickers and apply them in the proper area. Do not peel the backing paper off all at once. Peel off one corner of the backing and cut off with scissors. Arrange sticker on model and when satisfied adhere the corner without backing.
-
Page 22: Control Surface
ZLIN 31- Balance Z-526 Note: Adjust the location of the battery pack to achieve this C.G location. (107-110mm) DO NOT try to fly an out-of balance model! Wing center section 30- Control surface (15mm) (12mm) (12mm) (15mm) ELEVATOR STROKE AILERON STROKE (25mm) (25mm) RUDDER STROKE...