Page 1
Jost ® Dustless Sander Super Pads Dust Extractors Operation Manual: 1-15 操作手冊:頁 16-31 IMPORTANT NOTICE! H E A D P O S I T I O N I S F O R S A N D I N G C E I L I N G S H E A D P O S I T I O N I S F O R S A N D I N G WA L L S &...
Page 2
Lightweight design is built Extraction system and Industrial ® powers on/off automatically when tough for the most demanding Grade construction is also the Intex Giraffe is switched on/ conditions and significantly compatible for use in alternative ® off. Lockable power switch enables...
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains operated (corded) power tool or battery-operated (cordless) power tool.
Page 4
Use of the power tool for operations different from those intended could result in a hazardous situation. 5) SERVICE Have your power tool serviced by an Authorised Service Center, using only identical and genuine Intex Giraffe replacement parts.
SYMBOLS USED IN THIS MANUAL volts amperes read these instructions hertz watt always wear eye protection alternating current always wear a dust mask. no load speed min-1 revolutions or reciprocation per minute always wear hearing protection warning of general danger wear safety-approved hard hat do not dispose of electric class II tool...
® ® per Pads Dust Extractors For superior dust extraction, we recommend the german made range of Intex starmix ® dust extractors/vacuums. ELECTRICAL CONNECTION The network voltage must conform to the voltage indicated on the tool name plate. Under no circumstances should the tool be used when the power supply cable is damaged.
® Sander Super Pads Dust Extractors For excellent finish, we recommend the German made range of Intex Useit Super Pads. ® TO REPLACE CUSHIONED INTERFACE PAD The sponge pad must be perfectly flat to get good sanding results. If it is deformed or damaged it will cause very uneven sanding.
Page 8
® ® per Pads Dust Extractors For superior dust extraction, we recommend the german made range of Intex starmix ® dust extractors/vacuums. STARTING AND STOPPING TOOL Make sure that the power circuit voltage is the same as that shown on the specification plate of the machine and that switch is “OFF”...
Speed Adjustment ADJUSTING THE ROTATION SPEED The speed of the machine is variable to suit different tasks. It can be adjusted from 650/min up to 1600/min by using the thumb wheel. turn in the counterclockwise direction to increase the speed and in the clockwise direction to decrease the speed. Generally, you should use the higher speed for fast stock removal and the lower speed for more precise control.
The Carbon Brushes are a normal wearing part and must be replaced when they reach their wear limit. The Intex Power Sanders are fitted with an auto-stop Carbon Brush, this mechanism will stop the Motor when the brush reaches its wear limit, preventing damage to the Armature.
Page 11
TO INSPECT OR REPLACE BRUSHES; 1. Unplug the machine and lay it on its left side. 2. Unscrew the Handle Housings by removing the four screws. 3. Remove the housing covers by removing the six screws. 4. Remove the Motor, while ensuring the first Drive Shaft, located in the column, remains attached to the secondary Drive Shaft.
Page 12
WIRING THE WIRING Intex Giraffe intexinternational.com ®...
EXPLODED VIEW WARNING: To reduce the risk of injury, user must read and understand operator’s manual.
Page 14
SPINDLE VELCRO SPONGE PAD C - CLIP R-30 VELCRO STRAPS EXTENSION COLLUMN (GS 225G) 989.22mm BAIL HANDLE CARRY BAG FOAM HANDLE GRIP 253mm FELT SEAL Ø12.8 x Ø24 x 1 FIRST DRIVE SHAFT (GS 225G) 704L Intex Giraffe intexinternational.com ®...
Page 15
PARTS LIST 1060 mm (L) Type Parts Name Q'TY Parts Name Q'TY VACUUM EXTENSION HOSE 4M FIRST DRIVE SHAFT 254L QUICK RELEASE HOSE CONNECTOR SHAFT CONNECTOR CORD ARMOR BALL BEARING 6001-VV POWER SUPPLY CABLE C - CLIP S-12 SCREW M4 x 12 RIGHT DRIVE COVER CABLE CLIP LEFT DRIVE COVER...
Page 16
Giraffe , Starmix & Useit are registered Trademarks of Intex International. ® ® ® The information contained in this brochure was correct at the time of printing. E&OE MANAG700 Version:20160726-01/20...
Need help?
Do you have a question about the Giraffe and is the answer not in the manual?
Questions and answers