Sun2Solar 475175 Manual

Sun2Solar 475175 Manual

Above ground solar reel

Advertisement

Quick Links

Sun2Solar® Above Ground Solar Reel
(model # 475175 & 475179)
Read and follow all instructions. Locate and verify you have all parts before starting.

Parts List:

A) 2 – Wheel Handles (BSP34)
B) 2 – Hubs (BSP33)
C) 2 – Supports (Yolk) (BSP45)
D) 2 – Bases (BSP37)
E) 4 – Top Rail Attachments | 2-Right,
2-Left (BSP38)
Hardware Pack Includes:
F) 4 – Bearing Casing Tubes (BSP43)
G) 4 – Bearing Pins (BSP44)
H) 8 – Straps (BSP42)
I) 16 – Cover Clips (BSP40)
J) 16 – Plastic Nuts
K) 16 – Plastic Bolts
L) 20 – 1 ½" hex washer head screws
(BSP39)
M) 12 – ¾" screws (BSP41)
N) 2 – 1" screws (BSP35)
Do not sit or stand on reel system
Stay off cover – will not support weight
Do not attempt to stand on cover
Keep children and pets away – children
and pets cannot be seen under cover
Remove standing water
1

WARNING

AVOID DROWNING RISK
Children can drown on top of cover
Remove cover(s) completely before entry of
bathers – entrapment is possible
Non-secured or improperly secured covers are a
hazard
Do not allow anyone to swim under the cover
Failure to follow all instructions may result in
injury or drowning

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 475175 and is the answer not in the manual?

Questions and answers

Dale Ellgass
June 16, 2025

I need to order Cover Clips, Plastic Bolts, and Plastic Nuts for a Sun2Solar cover Model # 475175

Summary of Contents for Sun2Solar 475175

  • Page 1 Sun2Solar® Above Ground Solar Reel (model # 475175 & 475179) Read and follow all instructions. Locate and verify you have all parts before starting. Parts List: A) 2 – Wheel Handles (BSP34) B) 2 – Hubs (BSP33) C) 2 – Supports (Yolk) (BSP45) D) 2 –...
  • Page 2 Insert small tube into large tube and telescope it to fit your size pool. Please Note: There are 2 size model reels. Model: #475175 For above ground pools up to 21ft. wide. If your pool is 21ft. wide, solar cover must be placed offset center.
  • Page 3 With tubes laid out on a flat surface, make sure you have 9” minimum overlap of tubes. Start 3” in from end of each tube; drill pilot hole using 1/8” drill bit. Insert screw (L) in pre-drilled pilot hole, repeat this on the opposite side of the same tube. Repeat the step above 3 more times on each overlapping section to secure tube assembly.
  • Page 4 Place base mount on top rail. NOTE: Model: #475175 For above ground pools up to 21ft. wide. If your pool is 21ft. wide, solar cover must be placed offset center. For 18ft. wide oval pools, solar reel must be placed offset just passed the radius portion of the pool.
  • Page 5 NOTE: Rail attachment brackets should be mounted so that base slides toward pool water. Drill pilot hole for brackets. Insert screws (M) provided to attach base to top rail. Yolk & Bearing Casing/Pins Place yolk (C) into base mounted to the top rail Insert bearing pins (G) inside casing tube (F).
  • Page 6 Attaching Cover to Straps Re-install tube assembly on base. With cover laying on pool water, make mark on cover with tape or marker just below where reel will be set on top rail across the pool. Remove solar cover along with tube assembly. Set on ground and lay tube assembly over cover to make attaching easier.

This manual is also suitable for:

475179

Table of Contents