1
Battery Installation / Replacement
®
™
• Unscrew the battery cover with a Phillips head screwdriver (not included).
• Install 2 "D" alkaline batteries (not included) in the orientation (+/-) shown.
INSTRUCTIONS
• Replace battery cover and tighten screw.
• Replace the batteries when booster can no longer propel cars through the
track set.
• For best performance use only alkaline batteries.
Protect the environment by not disposing
of this product with household waste
[2002/96/EC]. Check your local authority
for recycling advice and facilities.
Please keep these instructions for future
reference as they contain important information.
CONTENTS
4+
N8899-0920
x14
BATTERY SAFETY INFORMATION
x2
In exceptional circumstances batteries may leak fluids that can cause a chemical burn injury or ruin your product. To
x2
x2
x4
avoid battery leakage:
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the product before being charged (if designed to be removable).
• Rechargeable batteries are only to be charged under adult supervision (if designed to be removable).
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
• Do not mix old and new batteries.
• Only batteries of the same or equivalent type as recommended are to be used.
• Batteries are to be inserted with the correct polarity.
• Exhausted batteries are to be removed from the product.
• The supply terminals are not to be short-circuited.
• Dispose of battery(ies) safely.
• Do not dispose of this product in a fire. The batteries inside may explode or leak.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
GRAY RUBBER BAND
NOTE: Changes or modifications not expressly approved by the manufacturer responsible
for compliance could void the user's authority to operate the equipment.
PURPLE RUBBER BAND
ORANGE RUBBER BAND
Mattel, Inc., 333 Continental Blvd., El Segundo, CA 90245 U.S.A. Consumer Relations 1 (800) 524-8697
YELLOW RUBBER BAND
service.mattel.com. • Mattel Canada Inc., Mississauga, Ontario L5R 3W2. You may call us free at 1-800-524-8697.
• Mattel U.K. Ltd., Vanwall Business Park, Maidenhead SL6 4UB. Helpline 01628500303 • Mattel Australia Pty., Ltd.,
Richmond, Victoria. 3121.Consumer Advisory Service - 1300 135 312. • Mattel East Asia Ltd., Room 1106, South
Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China. • Diimport & Diedarkan Oleh: Mattel SEA Ptd
WARNING:
WARNING:
!
Ltd.(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf Country Resort, 47410 PJ.
CHOKING HAZARD –
CHOKING HAZARD
Small parts.
Not for children under 3 years.
Tel:03-78803817, Fax:03-78803867.
Requires 2 "D" alkaline batteries (not included).
© 2008 Mattel, Inc. All Rights Reserved.
8
Assemble Power Loop
™
Assemble Power Loop
1
3
b
a
2
4
b
2
Assemble See-saw
1
2
YELLOW
RUBBER BAND
BACK VIEW
3
4
9
™
(Continued)
Assemble Spiral Spin-Out
™
1
a
2
b
3
a
3
5
Assemble Flame Jump Launcher
Assemble Mini Slide
c
1
1
b
2
a
2
4
Assemble Free-fall Platform
6
Assemble Swing
10
Assemble Drop Tower
™
Replace Rubber Band (Continued)
1
BOTTOM VIEW
BACK VIEW
2
11
Replace Rubber Band
ADULT SUPERVISION REQUIRED.
a
b
3
ORANGE RUBBER BAND
7
Assemble Zigzag Slide
1
2
BOTTOM VIEW
3
Replace Rubber Band (Continued)
1
BOTTOM VIEW
PURPLE RUBBER BAND
2
GRAY RUBBER BAND
b
a
b
3
INSTRUCTION SHEET
SPECIFICATIONS
Toy:
HW
Toy No.:
N8899
Part No.:
0920
Trim Size:
36"W x22" H
Folded Size:
6" W x11" H
Type of Fold:
accordian
# colors:
1C +1C
Colors:
Black
Paper Stock:
White Offset
Paper Weight:
100 lb.
EDM No.:
A.
B.
b
a
a
Need help?
Do you have a question about the Hot Wheels Trick Tracks Ultimate Stunt World and is the answer not in the manual?
Questions and answers