Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Hoffman nvent Genesis HB16
Summary of Contents for Hoffman nvent Genesis HB16
- Page 1 HB16 Instruction Manual...
- Page 2 GENESIS Top-MounT Air CondiTioner HB16 Model INSTRUCTION MANUAL Rev. M 87976428 © 2019 nVent P/N 10-1 008-0 6...
-
Page 3: Table Of Contents
Contact nVent Equipment Protection if further information is required. WARRANTY AND RETURN POLICY https://hoffman.nvent.com/en/hoffman/warranty-information C-NET INDUSTRIAL LTD. | +44(0)121 544 8608 | INFO@CNET-IS.CO.UK | WWW.CNET-IS.CO.UK 87976428 - 2 -... -
Page 4: Handling
HANDLING To avoid possible shipping damage and facilitate transportation and storage, the HIBOY® air conditioner was shipped in a freight carrier tested corrugated container in its normal mounting position. After uncartoning, be certain that the air conditioner is placed in its normal upright mounting position for a minimum of � e (5) minutes before operating, in order to allow the compressor oil to drain to the compressor sump area. -
Page 5: Technical Information
TECHNICAL INFORMATION DESIGN DATA BTU/Hr. @ Maximum Full Load Maximum Shipping Weight Model Voltage Hertz Phase °F Ambient Amps Ambient (lb. / kg) Temperature Temperature HB160816GXXX 50/60 18.8/20.4 7075/8133 145/66 HB160826GXXX 50/60 9.4/10.2 7075/8133 145/66 HB160846GXXX 50/60 5.2/5.6 7075/8133 160/73 C-NET INDUSTRIAL LTD. -
Page 6: Bench Testing
BENCH TESTING CAUTION To avoid possible damage to the air conditioner, it must be in an upright operating �������������� e (5) minutes before functional testing is started. When “bench testing the HIBOY® air conditioner before mounting to the electronic enclosure, follow the procedures outlined in the following paragraphs: Make sure that the HIBOY®... -
Page 7: Installation Instructions
INSTALLATION INSTRUCTIONS MOUNTING INSIDE OF THE ENCLOSURE 1. Slide rails must be provided for supporting the rear portion of the air conditioner. Do not depend on the units mounting ���� o support the entire weight. For mounting opening cutout dimensions, see Figure 2. 2. -
Page 8: Mounting On Top Of The Enclosure
MOUNTING ON TOP OF THE ENCLOSURE 1. Make sure the enclosure design is capable of supporting the air conditioners weight. For interfacing air “IN” and “OUT” openings, refer to Figure 4. Also refer to Dimensional Drawings on page 11. 2. To avoid cross-thr eading mounting inserts, start bolts by hand before tightening with a wrench or ratchet driver. -
Page 9: Principles Of Operation
PRINCIPLES OF OPERATION HIBOY® air conditioners are designed ������ to cool and dehumidify the internal environments of cabinets and enclosure which are used to package electronic components, thus assuring a cool, clean atmosphere for reasons of optimum performance and longevity. Hot air inside the electronic enclosure or rack is removed and cooled by means of refrigeration. -
Page 10: Maintenance
MAINTENANCE COMPRESSOR The compressor requires no maintenance. It is hermetically sealed, properly lubricated at the factory and should provide years of satisfactory operating service. Should the freon charge be lost, recharging ports (access ����� on the suction and discharge sides of the compressor are provided for recharging and/or checking suction and discharge pressures. -
Page 11: How To Remove, Clean Or Install Anew Filter
HOW TO REMOVE, CLEAN OR INSTALL A NEW FILTER 1. Lift ����� up so the bottm clears the ������� etainer. 2. Pull the bott������������� pushing down until the top of the ��� clears the upper retainer. If the unit is operating, carefully remove it assuring no dirt from �����... -
Page 12: Dimensional Drawings
DIMENSIONAL DRAWINGS HB16 Models 8000 BTUs/Hr. (2051 Watts) C-NET INDUSTRIAL LTD. | +44(0)121 544 8608 | INFO@CNET-IS.CO.UK | WWW.CNET-IS.CO.UK 87976428 - 11 -... -
Page 13: Parts List
PARTS LIST (Specify model and serial numbers when ordering parts) Item Number Part Number Quantity Description 10-1000-08 Inlet Filter, Reusable Aluminum 16-7001-00 Coil, Condenser 52-6034-10M Blower, Condenser (115 V) 52-6025-10M Blower, Condenser (230 V) 52-6075-00 Blower, Evaporator (115 V) 52-6076-00 Blower, Evaporator (230 V) 52-6121-01 Coil, Evaporator (8000-9000 BTU/Hr.) -
Page 14: Parts Exploded View
PARTS EXPLODED VIEW C-NET INDUSTRIAL LTD. | +44(0)121 544 8608 | INFO@CNET-IS.CO.UK | WWW.CNET-IS.CO.UK 87976428 - 13 -... -
Page 15: Wiring Schematic
WIRING SCHEMATIC C-NET INDUSTRIAL LTD. | +44(0)121 544 8608 | INFO@CNET-IS.CO.UK | WWW.CNET-IS.CO.UK 87976428 - 14 -... -
Page 16: Electrical Schematic
ELECTRICAL SCHEMATIC C-NET INDUSTRIAL LTD. | +44(0)121 544 8608 | INFO@CNET-IS.CO.UK | WWW.CNET-IS.CO.UK 87976428 - 15 -... - Page 17 C-NET INDUSTRIAL LTD. | +44(0)121 544 8608 | INFO@CNET-IS.CO.UK | WWW.CNET-IS.CO.UK P/N 10-1 008-0 6 87976428 Rev. M...
- Page 18 +44 (0)121 544 6808 info@cnet-is.co.uk C-NET Industrial Solutions Limited Suite 12, Sandwell Business Centre Oldbury Road Smethwick B66 1NN United Kingdom...
Need help?
Do you have a question about the nvent Genesis HB16 and is the answer not in the manual?
Questions and answers