Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Wolf Transition
Summary of Contents for Wolf Transition
- Page 1 INSTALLATION GUIDE C A B I N E T R Y...
-
Page 2: Tools Required
The instructions given here serve as general guidelines on how to install full-access cabinets in a reasonably simple installation. Many cabinet designs and installations may be far more complex and beyond the scope of these instructions and require a professional installer. •... - Page 3 LAYOUT AND PLANNING THE INSTALLATION Take inventory of the cabinets as per the plan or order. Find the high spot in the floor using a level as shown below. Locating the High Point on the Floor for a Wall Locating the High Point on the Floor for an Adjacent wall Wall High point of floor wall 1 High point of floor wall 1...
- Page 4 It is best when installing a larger kitchen to mark the cabinet positions and code (size) on the wall. Better to find out now if things aren’t going to fit just right than after you’ve installed several cabinets. Unbox the cabinets and be cautious not to drag them across the floor.
- Page 5 • Cabinets should be shimmed up from the floor level to the 34 ½" line with wood or composite shims. • Cabinets should also be shimmed out from the wall to maintain a straight line. Wolf Transition cabinets are designed to be a “frameless construction,” which means when the cabinets are screwed together they will be forced into a straight line regardless of how wavy or bowed the wall or surface they’re...
- Page 6 CORRECTING FOR A “BOWED IN” OR “BELLIED” WALL CONDITION W3036 W3036 W3036 Boxes are at an angle Boxes are not aligned to each other W3036W 3036W 3036 Proper shimming will allow cabinet boxes to be aligned along a flat plane and the door facia to be adjusted within acceptable tolerances FASTENING CABINETS TO THE WALL Screw wall cabinets and tall cabinets to the predetermined height through the back panel into a stud.
-
Page 7: Fastening Cabinets Together
FASTENING CABINETS TOGETHER Align cabinet cases together carefully. Cabinet cases can be clamped together using various kinds of clamps; however, use caution with any kind of steel clamp to not damage the surface material of the cabinet. Screw cabinets together with #7 x 1-1/8" flathead screws. INSTALLING FILLERS Cabinets come in 3"... -
Page 8: Other Configurations
INSTALLING TRIM • Installing crown moulding can be accomplished in a variety of ways depending on the application. Using “full-access cabinets” means that a sub-crown moulding will always have to be screwed to the top of the cabinet case to attach the crown moulding to. ATSM by itself as Topscribe ATSM as Crown-Crown Spans to Ceiling ATSM as Sub-Crown... - Page 9 INSTALLING LIGHT RAIL • In the same way, light rail will have to be screwed to the bottom of the case. Light Rail Screw Placement Side View #7 x 1- 5/8" Flathead screw Predrill 3/16" Countersunk Clearance Hole for AMLR2 AMLR5 #7 x 1-1/8"...
- Page 10 ADJUSTING HINGES AND DRAWERS Hinge Adjustment Open Door View Out of Alignment Alignment Condition Condition Corrected Up and Down Adjustment Side to Side Adjustment In and Out Adjustment Hinge Removal and Reinstallation Mounting To remove a mounted hinge: plate • Push the release plunger in from the back of the hinge •...
- Page 11 Steel Drawer Adjustment Rear View Out of Alignment Alignment Condition of Open Drawer Condition Corrected Drawer Face Removal Clamp Screw Height Adjustment Screw Side to Side Adjustment Screws Dovetail Drawer Adjustment • To adjust the dovetail drawer for alignment, slide the white plastic clip on the under side of the drawer back and forth to raise and lower the left and right sides of the drawer.
-
Page 12: Year Limited Warranty
HOW TO OBTAIN SERVICE APPLICABLE UNDER THIS WARRANTY If you need replacement parts or would like to make a warranty claim, please contact your Wolf Transition cabinet dealer or the manufacturer by mail, email, fax or telephone at the address or phone numbers listed below:...