Advertisement
Quick Links
Advertisement
Summary of Contents for Strata Corner Workstation
- Page 1 Corner Workstation Assembly Instructions Flexible Options. Consistent Style. Enduring Quality.
- Page 2 Parts Before beginning assembly of Strata Electric Corner Workstation, please ensure you have all all of the below listed parts and in the specified quanties. A - Leg (3) B - Feet (2) C - Mid Post Base (1) D - Outer Frame Left (2)
- Page 3 Phillips Screw Driver 5 x 20 or Cordless Drill M10 x 35 5mm Allen Wrench Leveler Hand Tailstock Screw 4mm Allen Wrench M6*8+BW 4mm Allen Wrench Phillips Screw Driver M5*8 or Cordless Drill M10*20 8mm Allen Wrench Corner Workstation Assembly Instructions...
- Page 4 Attach Mid Post Frame Left (I) and Mid Post Frame Right (J) to a Leg (A) with 4 screws (G). Step 2 Attach Mid Post Bracket (K) to Mid Post Frame Left & Right (I & J) using 2 screws (G). STRATA ELECTRIC...
- Page 5 Step 3 Attach the Mid Post Base (C) to Leg (A) using 4 screws (I). Step 4 Attach the Leveler (E) to the bottom of the Mid Post Base (C). Corner Workstation Assembly Instructions...
- Page 6 Step 5 Attach 2 of the Inner Frame (F) to the Mid Post Frame Left (I). Step 6 Attach one each of the Outer Frame Left (D) and Outer Frame Right (E) to the Inner Frame (F). STRATA ELECTRIC...
- Page 7 Repeat Step 5 and Step 6 on the opposite side for Mid Post Frame Right (J). Step 8 Attach a Leg (A) to the Outer Frame Left (D) and Outer Frame Right (E) using two screws (A). Corner Workstation Assembly Instructions...
- Page 8 Step 9 Repeat Step 8 for the opposite side. Step 10 Attach the Top Side Frame Left (G) and Top Side Frame Right (H) to both ends of the desk. STRATA ELECTRIC...
- Page 9 Step 11 Straighten both end Legs (A) upright. Step 12 Screw 4 screws (A) into the Outer Frame Left (E) and Outer Frame Right (D) on both ends.. Corner Workstation Assembly Instructions...
- Page 10 Step 13 Attach the Controller (L) to the frame at desired end using 2 screws (H). Step 14 Attach the optional Wood Top Bracket (M) using 8 screws (C) if desired. STRATA ELECTRIC...
- Page 11 Step 15 Connect the Handset (P) cable to the Controller (L). Step 16 Connect the Cable Extension (N) to the opposite end Leg (A). Corner Workstation Assembly Instructions...
- Page 12 Step 17 Connect all 3 Leg (A) cables to the Controller (L). Step 18 Connect the Power Cable (O) to the Controller (L). STRATA ELECTRIC...
- Page 13 Step 19 Adjust frame to fit worktop. Step 20 Secure the worktop using 27 screws (C). Screw the handset using 2 screws (B). Corner Workstation Assembly Instructions...
- Page 14 Step 21 Tighten the 8 screws (F) on the telescopic frame to firmly secure it to the right length. Note: Screw F is preinstalled. Step 22 Attach Feet (B) using 8 screws (D) then install the Levelers (E). STRATA ELECTRIC...
- Page 15 Handset at the same time for 3 seconds. Continue pressing the buttons until all legs are in the lowest position. When finished reset, the control box makes an alert sound, and the buttons can be released. Done! Corner Workstation Assembly Instructions...
- Page 16 Flexible Options. Consistent Style. Enduring Quality.
Need help?
Do you have a question about the Corner Workstation and is the answer not in the manual?
Questions and answers