Table of Contents
Advertisement
USER MANUAL
WARRANTY CARD
EXCHANGE PARTS CATALOG
To the chippers: RT-630
eRRead all instructions carefully before working
with the device, become familiar with all control
elements. In case of doubt, contact the man-
ufaturer.
Keep the manual in a safe place in order to obtain
all necessary information at any times.
REMET CNC TECHNOLOGY
Limited Liability Company
36-053 Kamień, Łowisko 320A
VAT No PL5170374653
Original instruction
Advertisement
Table of Contents
Related Manuals for REMET CNC RT-630
Summary of Contents for REMET CNC RT-630
- Page 1 USER MANUAL WARRANTY CARD EXCHANGE PARTS CATALOG To the chippers: RT-630 eRRead all instructions carefully before working with the device, become familiar with all control elements. In case of doubt, contact the man- ufaturer. Keep the manual in a safe place in order to obtain all necessary information at any times.
-
Page 2: Table Of Contents
REMET CNC TECHNOLOGY SP. Z O.O. Table of Contents GENERAL SCHEME ........................... 3 2. PRPOPOSE AND GENERAL DESCRYPTION OF THE DEVICE ..............4 DEVICE SPECIFICATION ........................5 SAFETY ADVICES ..........................6 Generl remars: ..........................6 Activities after finishing work......................11 PROHIBITED ACTIONS ........................ -
Page 3: General Scheme
REMET CNC TECHNOLOGY SP. Z O.O. 1. GENERAL SCHEME Page 3 z 22 Manufacturer of machinery and equipment, CNC machining service... -
Page 4: Prpopose And General Descryption Of The Device
REMET CNC TECHNOLOGY SP. Z O.O. 2. PRPOPOSE AND GENERAL DESCRYPTION OF THE DEVICE The device is designed for shredding woody and fibrous garden waste, such as cuttings from tree branches and branches. Warning: This symbol is used in these instructions if there is a danger to the user or bystanders. -
Page 5: Device Specification
REMET CNC TECHNOLOGY SP. Z O.O. 3. DEVICE SPECIFICATION Technical specifications: RT-630 MINIMUM / RECOMMENDED POWER 25/50* * [HP] RECOMMENDED ROTATION PTO 750-1000 SHAFT (RIGHT SIDE) [rpm] CUTTER DIAMETER [mm] NUMBER OF KNIVES 4 + 1 przeciw ostrze Material of CUTTING KNIVES... -
Page 6: Safety Advices
REMET CNC TECHNOLOGY SP. Z O.O. 4. SAFETY ADVICES Generl remars: The use of wood chippers is forbidden by: Unauthorized persons, untrained, unfamiliar with the instructions for use or • under the influence of alcohol or narcotics and psychotropic substances... - Page 7 REMET CNC TECHNOLOGY SP. Z O.O. Personal protective equipment and pictograms During working with a wood chipper, use: protective glasses or a face mask • • ear protectors • protective gloves protective footwear • protective clothing, tight fitting to the body, without loose straps or sleeves.
- Page 8 REMET CNC TECHNOLOGY SP. Z O.O. Page 8 z 22 Manufacturer of machinery and equipment, CNC machining service...
- Page 9 REMET CNC TECHNOLOGY SP. Z O.O. Security signs: 1. Safety signs must be kept clean at all times and legible. 2. Immediately replace security signs that are missing or have become illegible. 3. The replaced parts which had the safety mark (s) should also be given a valid mark.
- Page 10 REMET CNC TECHNOLOGY SP. Z O.O. Aggregating with a tractor: 1. Observe the recommended minimum tractor front load in order to maintain stability. 2. Be extremely careful when coupling the shredder with the tractor and when disconnecting it. 3. Each time before starting work, check the correct operation of all safety switches.
-
Page 11: Activities After Finishing Work
REMET CNC TECHNOLOGY SP. Z O.O. 8.Before inserting the material to be cut into the inlet funnel, pay attention that the material does not contain any foreign elements harder than wood, such as stones, wires, ropes, nails, rivets, chains, etc., which may damage the knives,... - Page 12 REMET CNC TECHNOLOGY SP. Z O.O. Rules of conduct in emergency situations posing a threat to employees' life or health. 1. After finding defects, damage or improper operation of the machine or its copo- nents, the wood chipper shall be immediately turned off and immobilized and the superior should be notified.
-
Page 13: Prohibited Actions
REMET CNC TECHNOLOGY SP. Z O.O. PROHIBITED ACTIONS It is forbidden to work with a chopper after consuming alcohol or narcotic drugs and psychotropic substances (drugs) and drugs that weaken the ability to react. It is forbidden to use the chipper by: •... -
Page 14: Comments And First Aid
REMET CNC TECHNOLOGY SP. Z O.O. Comments and first aid Report any accident at work to your supervisor, and leave the workplace in the condition in which the accident occurred. 2. Always be prepared to get the following equipment: •... -
Page 15: Choosing Power Shaft
REMET CNC TECHNOLOGY SP. Z O.O. 7. CHOOSING POWER SHAFT To ensure compatibility with a diverse group of 3-point mounting systems, the power transmission shaft may be too long or too short. It is particularly important that the transmission through the telescopic shaft is carried out freely, but without tapping to limit the operating range. -
Page 16: Replacing And Aliginig The Blade Axis
REMET CNC TECHNOLOGY SP. Z O.O. 8. REPLACING AND ALIGINIG THE BLADE AXIS Before adjusting the position of the knives or replacing them, disconnect the device from the power source and place it on a stable, level and non-slippery sur- face. -
Page 17: Replaceable Parts And Installation
REMET CNC TECHNOLOGY SP. Z O.O. 9. REPLACEABLE PARTS AND INSTALLATION Spare parts and assembly Spare parts can be ordered directly from the manufacturer. When ordering, please indicate the type of device. Page 17 z 22 Manufacturer of machinery and equipment, CNC machining service... - Page 18 REMET CNC TECHNOLOGY SP. Z O.O. Page 18 z 22 Manufacturer of machinery and equipment, CNC machining service...
- Page 19 REMET CNC TECHNOLOGY SP. Z O.O. Page 19 z 22 Manufacturer of machinery and equipment, CNC machining service...
-
Page 20: Maintenance And Cleaning
REMET CNC TECHNOLOGY SP. Z O.O. MAINTENANCE AND CLEANING Safety instructions for maintenance.. Before performing maintenance or repair, the device must be disconnected from the power source and stand on a stable, level and non-slippery surface. The device should be cleaned before and after each use, and the tightening of the cover fixing screws must be checked. -
Page 21: Warranty Card
REMET CNC TECHNOLOGY SP. Z O.O. 13. WARRANTY CARD Device symbol: ……………………………… Serial number: ………………………………. Production date: 202.…………………… Sales date: ……………………………………. Signature : ………………..…………….….………..… _______________________ Stamp GUARANTEE PROCEDURES: 1. This device has a 24-month warranty. The reduced warranty period (12 months) applies to business, commercial and any other pri- vate use. - Page 23 WWW.MARGUCIAI.LT INFO@MARGUCIAI.LT Nauja technika: +370 685 54521 Naudota technika iš Danijos: +370 656 24532 Lenkiškos technikos atsarginės dalys: +370 615 68799 Skandinaviškos technikos atsarginės dalys: +370 682 51607 Farmtrac atsarginės dalys: +370 626 19138 Chemikalų purkštuvai, patikra: +370 616 55819 Fermų...
Need help?
Do you have a question about the RT-630 and is the answer not in the manual?
Questions and answers