Table of Contents
Advertisement
Quick Links
Thor Gas Griddle
Installation and Operation Instructions
Model: GL167-P , GL167-N, GL168-P , GL168-N
Please complete this information and retain this manual for the life of the equipment. For
Warranty Service and/or parts, this information is required.
Model Number
WARNING: For your safety, do not store or use gasoline or other flammable vapors
or liquids in the vicinity of this or any other appliances. Keep the area free and clear
of combustible materials.
WARNING：Improper installation, adjustment, alteration, service or maintenance
can cause property damage, injury, or death. Read the installation operating and
maintenance instructions thoroughly before installing, or servicing this equipment.
WARNING ： Instructions must be posted in a prominent location. All safety
precautions must be taken in the event the user smells gas. Safety information can be
obtained from your local gas supplier.
IMPORTANT FOR FUTURE REFERENCE
Fourth Way, Avonmouth, Bristol, BS11 8TB
Serial Number
Date Purchased
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for THOR GL167-P
Summary of Contents for THOR GL167-P
- Page 1 Thor Gas Griddle Installation and Operation Instructions Model: GL167-P , GL167-N, GL168-P , GL168-N IMPORTANT FOR FUTURE REFERENCE Please complete this information and retain this manual for the life of the equipment. For Warranty Service and/or parts, this information is required.
-
Page 2: Table Of Contents
Contents Introduction ..................... 2 Specifications ................... 3 General Pack Contents Gas Supply Requirements Dimensions ....................4 Installation ....................5 Installation Requirements Unpacking Location Clearances Assembly Gas Connection Commissioning Install gas stand Operation ....................10 Operation Guide Lighting the Main Burner Cleaning and Maintenance ................ -
Page 3: Introduction
Introduction We are confident that you will be delighted with your Thor Gas Griddle, and it will become a most valued appliance in your commercial kitchen. To ensure you receive the utmost benefit from your new Gas Griddle, there are two important things you can do. -
Page 4: Specifications
General Commercial, heavy duty, gas griddle with full pilot and flame failure protection and piezo ignition. It uses a 19mm thick griddle smooth plate. Pack Contents The following is included: Thor Gas Griddle Gas Stand Instruction Manual ... -
Page 5: Dimensions
Dimensions GL167-P / GL167-N GL168-P / GL168-N... -
Page 6: Installation
Installation Installation Requirements NOTE: • It is most important that this appliance is installed correctly and that operation is correct before use. Installation shall comply with local gas, health and safety requirements. • This appliance shall be installed with sufficient ventilation to prevent the occurrence of unacceptable concentrations of substances harmful to health. -
Page 7: Clearances
Installation Clearances NOTE: Only non-combustible materials can be used in close proximity to this appliance. Combustible Surface Non Combustible Surface Left / Right Hand Side 250mm Rear 250mm Assembly NOTE: • This appliance is supplied with adjustable stand to enable the appliance to be positioned securely and level. -
Page 8: Commissioning
Installation Check that the gas operating pressure. NOTE: The operating pressure is to be measured at the burner operating pressure test point outlet and with one griddle burner operating at the “High Flame” setting. Turn off the mains gas supply and bleed the gas out of the appliance gas lines. Turn on the gas supply and the appliance. -
Page 9: Install Gas Stand
Installation Install gas stand Remove the Stand from the packaging, ensuring that all protective packaging, plastic and residues are cleaned from its surfaces. Layout all components of the stand on the floor ready for assembly. You will need a screw-driver to assist in the assembly process Step 1 –... - Page 10 Installation Step 3 – Fix and tighten the screws. Fixing screws Step 4 – Locate the stand into required position, and adjust the adjustable feet into a level position, refit griddle plate.
-
Page 11: Operation
Operation Operation Guide CAUTION: • THIS APPLIANCE IS FOR PROFESSIONAL USE AND IS ONLY TO BE USED BY QUALIFIED PEOPLE. • ONLY QUALIFIED SERVICE PERSONS ARE TO CARRY OUT INSTALLATION, SERVICING OR GAS CONVERSION OPERATIONS. • COMPONENTS HAVING ADJUSTMENTS PROTECTED (E.G. PAINT SEALED) BY THE MANUFACTURER SHOULD NOT BE ADJUSTED BY THE USER/OPERATOR. - Page 12 Operation WARNING: SURFACE TEMPERATURE OF THE GRIDDLE PLATE CAN REACH OVER 300°C WHEN THE APPLIANCE IS OPERATED AT FULL SETTING. 1. Lighting the Main Burners The burners are fitted with individual standing pilots which allows the main burners to be turned ON- OFF without the need to manually re-light the burner each time that it is turned ON, as the burner will be automatically lit itself by the pilot burner.
- Page 13 Operation Main burner air supply: 1. For efficient burner operation, a proper balance of gas volume and primary air supply must be maintained which will result in complete combustion. Insufficient air supply results in a yellow streaming flame. Primary air supply is controlled by an air shutter on the front of the burner. 2.
- Page 14 Operation SEASON GRIDDLE: Heat to low temperature (300℉-350 ℉/150℃-180℃) and pour on a small amount of cooking oil, about one ounce (30cc) per square foot of surface. Spread the oil over the entire griddle surface with a cloth to create a thin film. Wipe off any excess oil with a cloth. Repeat this procedure 2 to 3 times until the griddle has a slick, mirror-like surface.
-
Page 15: Cleaning And Maintenance
Cleaning and Maintenance CAUTION: Always turn off the gas supply before cleaning. This appliance is not water proof. Do not use water jet spray to clean this appliance. General Clean the griddle regularly. A clean appliance looks better, will last longer and will perform better. Carbonised grease on the surface or on the griddle plate will hinder the transfer of heat from the cooking surface to the food. - Page 16 Cleaning and Maintenance Periodic Maintenance NOTE: All maintenance operations should only be carried out by a qualified service person. To achieve the best results cleaning must be regular and thorough and all controls and mechanical parts should be checked and adjusted periodically by a qualified service person. If any small faults occur, have them attended to promptly.
-
Page 17: Trouble Shooting
Trouble shooting This section provides an easy reference guide to the more common problems that may occur during the operation of your equipment. The fault finding guide in this section is intended to help you correct, or at least accurately diagnose problems with your equipment. Although this section covers the most common problems reported, you may encounter a problem not covered in this section. -
Page 18: Replacement Parts List
Replacement Parts List IMPORTANT: Only genuine authorized replacement parts should be used for the servicing and repair of this appliance. The instructions supplied with the parts should be followed when replacing components. For further information and servicing instructions, contact your nearest authorized service branch. When ordering replacement parts, please quote the part number and the description listing below. -
Page 19: Gas Conversion
Gas Conversion Conversion Procedure CAUTION: Ensure that the appliance is isolated from the gas supply before commencing servicing. NOTE: • These conversions should only be carried out by qualified persons. All connections must be checked for leaks before re- commissioning the appliance. •... - Page 20 Refit the control knobs to the front control panel. The control knobs are a push fit onto the shafts of the gas control valves. Remove the blots Injector of Pilot Burner Injector of Pilot Burenr. Digital mark is 25, the diameter of the Injector is ￠0.25mm.
- Page 21 WARNING: DO NOT USE A NAKED FLAME TO CHECK FOR GAS LEAKAGES. Check all gas connections for leakages. Check the following functions in accordance with the operating instructions • Light the Pilot Burner. • Light the Main Burner. • Check the ‘Low Fire’ burner operation. •...
- Page 22 Gas Conversion Kits Item Name Griddle Item No. Single supply Manifold Pilot Country of Main Burner burner Category Pressure Pressure Burner destination Injectors Heating (mbar) (mbar) Injectors Input(KW) AT,BG,CZ,DK,EE,FI,GR,HR, HU,IS,IE,IT,LV,LT,NO,PT, 44#(2.18) 0.45 RO,SK,SI,ES,SE,CH,TR,GB DE,LU,PL 44#(2.18) 0.45 BE,FR I2E+ 44#(2.18) 0.45 BE,CH,CZ,IT,ES,FR,GR,GB, I3P(37) 53#(1.51)
-
Page 23: Explosion Drawing
Explosion drawing: GL167-P / GL167-N... -
Page 24: Spare Parts List
Spare Parts List DESCRIPTION MODEL CODE GL167-P Dial 01.09.1050334 GL167-N GL167-P Thor Badge 01.02.1005263 GL167-N GL167-P Piezo Igniter 03.99.1290085 GL167-N GL167-P Control panel 01.05.1029277 GL167-N GL167-P Control rack 01.05.1028909 GL167-N GL167-P Safety Valve 01.20.1068524 GL167-N GL167-P Main pipe assy.-left 06.05.1471982... - Page 25 GL167-P Foot fix 06.05.1471839 GL167-N Orifice for LPG GL167-P 01.20.1068653 Orifice for Natural Gas GL167-N 01.20.1068644 GL167-P L connector 01.18.1067404 GL167-N GL167-P Main pipe assy. 06.05.1471980 GL167-N GL167-P 07.18.28.15909 Gas stand GL167-N GL167-P Oil tray assy. 06.05.1471847 GL167-N...
- Page 26 GL168-P / GL168-N...
- Page 27 Spare Parts List DESCRIPTION MODEL CODE GL168-P Dial 01.09.1050334 GL168-N GL168-P Thor Badge 01.02.1005263 GL168-N GL168-P Piezo Igniter 03.99.1290085 GL168-N GL168-P Control panel 01.05.1029282 GL168-N GL168-P Control rack 01.05.1028962 GL168-N GL168-P Safety Valve 01.20.1068524 GL168-N GL168-P Main pipe assy.-left 06.05.1471982...
-
Page 28: Declaration Of Conformity
GL168-P Foot fix 06.05.1471839 GL168-N Orifice for LPG GL168-P 01.20.1068653 Orifice for Natural Gas GL168-N 01.20.1068644 GL168-P L connector 01.18.1067404 GL168-N GL168-P Main pipe assy. 06.05.1471980 GL168-N GL168-P 07.18.28.15909 Gas stand GL168-N GL168-P Oil tray assy. 06.05.1471847 GL168-N... - Page 31 V1.Rev1.12-14...
Need help?
Do you have a question about the GL167-P and is the answer not in the manual?
Questions and answers