Summary of Contents for Barikell MK8 90
- Page 1 FLOAT MACHINE MK8 90 WITH HYDRAULIC CONTROLS BARIKELL SRL Via Razzaboni,118 41100 – Modena ( Italy) Tel 059.311178 fax 059.311111...
- Page 2 7 3 8 12 Fig. 3 Fig.1 Fig. 2 Fig. 5 Fig. 6 Fig. 4 Fig. 7 Fig. 8 Fig. 9 Fig. 11 Fig. 10 Fig. 12...
- Page 3 INNOVATIONS: New temp gages...
- Page 4 NEW LIFT HOOK...
- Page 6 The contents of this manual may be Thank you for buying our product. We have taken modified without prior notice or other every possible care to ensure that it arrives in obligations order incorporate perfect conditions. Nevertheless, in the unlikely changes and improvements to the units event that you find some damage when you already shipped.
-
Page 7: Table Of Contents
Table of Contents 5.3. Driving the float machine ......12 SYMBOLS ............ 8 5.4. Use ..............12 5.5. Stopping ............12 5.6. Stopping in emergency conditions .... 13 GENERAL PRECAUTIONS FOR USE ..8 HANDLING AND TRANSPORT ....13 TECHNICAL CHARACTERISTICS ....9 3.1. -
Page 8: Symbols
been damaged during transport, 1. Symbols Below follows a short legend with an indication of and if so, immediately notify the the symbols used throughout the manual (those manufacturer area considered most significant). representative. WARNING DANGER: draws • Allow only authorised personnel attention to situations or problems to use the machine. -
Page 9: Technical Characteristics
• Superior planarity of the floor surface (as a 3.1. Machine description The double rotary float machine model MK8 90 result of lowering of the machine barycentre) • Perfect vision has been designed and constructed to float The seat can be adjusted to the most comfortable concrete and bituminous floors of warehouses, driving position for the operator. -
Page 10: Main Parts Of The Machine And Controls
An exact description of the Model and Serial right-hand side, which executes four Number will make it easier for our Technical movements (forward, backward, right and left). Service to respond quickly and efficiently. The machine movements are controlled by a Therefore, always indicate the machine model pressure regulating valve (Fig.7) located in the and serial number when you contact Technical... -
Page 11: Component Assembly
4.3. Water supply there is sufficient space around the float machine (at least 2 m). (Fig.2) The hydraulic float machine MK8 90 has an autonomous wetting system. The water is 5.2. Starting sprayed in correspondence to the rotors from the nozzles connected to the water tank. -
Page 12: Driving The Float Machine
The engine is started at reduced rpm, the clutch The floor is ready for the first pass when the has not yet engaged and the rotors do not yet imprint of the shoe heel sinks into the concrete by rotate (the clutch engages at 1500 rpm). In order about 2-3 mm when walking on it. -
Page 13: Stopping In Emergency Conditions
7.2. Machine maintenance 3. Lower the handle of the trolley towards The hydraulic float machine model MK8 90 does the ground until the pivoting wheel require particular maintenance,... -
Page 14: Battery
3. Clean any oxidation off the two battery Slightly lift the float machine off the ground (about poles. 10 cm). Operations after 100 hours of work Mount the floats on the blades checking the Check the oil level in the two reduction gears (see correct direction of rotation. -
Page 15: Storage Instructions
To replace the oil filter open the support (3), If storing the machine in places where the unscrew filter proceed with temperature might drop to below 0°C drain out the replacement. water tank. 7.9. Storage instructions 7.10 Hydraulic pressure regulation Never store the machine with fuel in the tank in places where the fuel vapours The operating pressure of the MK8-90 may vary... - Page 16 You can address to all our authorized dealers all around the world. Barikell srl will refuse all responsibility in case of incident whenever the check-ups won’t be done.
-
Page 17: Disposal
Any repairs or operations carried out during only if confirmed in writing by BARIKELL srl the period of guarantee by unauthorised 14) The manpower and work required to replace...