Table of Contents
Advertisement
Quick Links
How to use Airlink Raven CDMA/GPRS
1
Introduction ........................................................................................................................ 1
2
CDMA/GSM connection to a Z-max base......................................................................... 2
2.1
Modem activation....................................................................................................... 2
2.2
Modem configuration................................................................................................. 2
2.2.1
Base side............................................................................................................. 2
2.2.2
Rover side........................................................................................................... 3
3
CDMA/GPRS connection to iCGRS.................................................................................. 4
3.1
Modem activation....................................................................................................... 4
3.2
Modem installation for the rover................................................................................ 4
3.2.1
First step - configuration of the modem ............................................................. 4
3.2.2
Second step - configuration of Z-max ............................................................... 5
3.2.3
Third step - Using Z-max with Airlink modem................................................. 6
3.2.4
Hang-up.............................................................................................................. 7
4
Reminder ............................................................................................................................ 8
5
Troubleshooting ................................................................................................................. 9
1 Introduction
This document provides all technical information required in order to connect CDMA or
GPRS Airlink modem to:
o a Z-max base
o an iCGRS base or any other GPS station that is streaming data on a socket (IP address
and port number)
This procedure is only valid for the following modems from Airlink:
• Raven GPRS modem G3210 or G3211
• Raven CDMA modem C3210
For the use of Airlink GSM or CDMA modem a special kit from Thales Navigation is
designed : Kit external Raven modem for Z-max (Ref:990572-01).This kit includes the
following items:
• A Serial cable (Ref:702078) to connect the serial port of Z-max to the modem
• A power cable (Ref: 702079) to power the modem from a battery
• A 11.1V / 6Ah Li-Ion battery (Ref:110284)
• A battery charger (Ref:110049)
• A Blue backpack RTK Z-max (Ref:205044)
17/08/2007
Modems with Z-max ?
1/ 21/
Advertisement
Table of Contents
Related Manuals for Airlink101 Raven G3210
Summary of Contents for Airlink101 Raven G3210
-
Page 1: Table Of Contents
How to use Airlink Raven CDMA/GPRS Modems with Z-max ? Introduction ........................1 CDMA/GSM connection to a Z-max base................. 2 Modem activation....................... 2 Modem configuration....................2 2.2.1 Base side......................2 2.2.2 Rover side......................3 CDMA/GPRS connection to iCGRS.................. 4 Modem activation....................... 4 Modem installation for the rover................ -
Page 2: Cdma/Gsm Connection To A Z-Max Base
2 CDMA/GSM connection to a Z-max base Modem activation The modem activation is a procedure that allow to the modem to be registered to the selected wireless operator. This procedure has only to be done for the first use of the modem. This procedure must be done for the rover and the base modems. -
Page 3: Rover Side
$PASHS,SPD,A,9 $PASHR,ACK Set PortA in 115.2Kbps $PASHS,DSY,A,C<CR><LF> $PASHR,ACK Set Z-max in transparent mode $PASHS,DSY,C,A<CR><LF> $PASHR,ACK Set Z-max in transparent mode AT\APASSTHRU<CR><LF> Wait 30 seconds before continue ATS0=1<CR><LF> Set the number of ring before connection $PASHS,DSY,OFF<CR><LF> $PASHR,ACK Remove the transparent mode The CDMA/GSM modem base is initialized, and ready to be used by the rover. -
Page 4: Cdma/Gprs Connection To Icgrs
3 CDMA/GPRS connection to iCGRS Modem activation The modem activation is a procedure that allow to the modem to be registered to the selected wireless operator. This procedure has only to be done for the first use of the modem. You should refer to the appendix 1, to activate the CDMA/GPRS modem. -
Page 5: Second Step - Configuration Of Z-Max
Once all parameters are displayed on the screen modify the following parameters: S53 Destination address -> Set the IP address of the iCGRS station ( Ask to the iCGRS manager which IP address is given for the iCGRS) S53 Destination port -> Set the selected port of the iCGRS station ( Ask to the iCGRS manager which port number is allocated to you) S53 Default Dial Code =T MD Startup Mode Default =4... -
Page 6: Third Step - Using Z-Max With Airlink Modem
Serial cable Bluetooth Execute FastSurvey, and after initializing the connection with Z-max : Select the “Equip” tab. Select “Receiver utilities” button Select “Send command to receiver” Send the following command to the receiver followed by OK Command to send to Z-max (*) Response from Z-max Comments $PASHS,SPD,B,9 $PASHR,ACK... -
Page 7: Hang-Up
It is not necessary to send specific command to Z-max, or fast Survey: As soon as the Airlink Raven modem is powered, an automatic connection procedure will occur to the iCGRS station selected during the first step of configuration. Z-max is ready to be used for RTK operation, with correction data on portB. 3.2.4 Hang-up Just disconnect the Airlink modem from its power source. -
Page 8: Reminder
4 Reminder Port A or B provides serial link and power access to Z-max. Port A Port B RS-232 serial link: RS-232 / RS-422 serial link • With hardware (RTS/CTS) flow • RS232 or 422 selection through control software enabled/disabled $PASHS command •... -
Page 9: Troubleshooting
5 Troubleshooting Symptoms Action • Check the cable or the Bluetooth link Z-max is not responding • Check if the baud rate match with current baud rate in Z-max • No response after a dial to a Z-max base Check the connection of the antenna on the modem •... - Page 10 Appendix 1 Activation of CDMA and GPRS Raven modem From Airlink 17/08/2007 10/ 21/...
- Page 11 How to activate CDMA and GPRS Airlink Raven Modem ? CDMA Raven modem for Verizon operator : 1) Before activate the modem you need the following items: - 1 PC with XP or Win2K Operating System - 1 CDMA Raven modem for Verizon C3210, its antenna and a source of power - 1 Serial cable to connect the modem to your PC - 1 software from Airlink Setup wizard for Verizon that can be downloaded at the Airlink Web site (http://www.airlink.com/support/modems/modem_utils.asp).The file to download is "SetupWizard1.zip"...
- Page 12 - Check the ESN number of the modem and then Next - Skip this step by selecting Next 17/08/2007 12/ 21/...
- Page 13 - Input the MSL code ( for Verizon it should be 000000) and then Next - Input the Phone number given by the operator in the MDN field and then next 17/08/2007 13/ 21/...
- Page 14 - Except if the provider give you the SID and NID parameters skip this section by next - Except if the provider give you different values for NAI and Password parameters skip this section with next 17/08/2007 14/ 21/...
- Page 15 - Select Automatic B option and the Next - Push the test button 17/08/2007 15/ 21/...
- Page 16 - Check if the Firmware version is up to date and then Next - Select the public internet option and then next 17/08/2007 16/ 21/...
- Page 17 - Check if the PRL list is up to date , if not select update button, else next - Check that everything is OK ( you will probably have to wait few minutes) and then next 17/08/2007 17/ 21/...
- Page 18 - Congratulations, your CDMA modem is activated then select finish. GPRS Raven modem for all operators : 1) Before activating the modem you need the following items: 17/08/2007 18/ 21/...
- Page 19 - 1 PC with XP or Win2K Operating System - 1 GPRS Raven modem for G3210, its antenna and a source of power - 1 Serial cable to connect the modem to your PC - 1 software from Airlink Wireless Ace 3G that can be at the Airlink Web site (http://www.airlink.com/support/modems/modem_utils.asp).
- Page 20 - On the left of the screen select Misc, and fill the following field : *NETUID with the user name provided by the operator *NETPW with the password provided by the oprator ! Be careful, respect the case ! then select at the left the GPRS parameter list - Fill the field + CGDCONT, in the following form "...
- Page 21 - You can exit the Wireless Ace 3G utility software, and after few minutes you should check that the Reg ( Registered) light on the modem is ON. Congratulations your modem is activated. 17/08/2007 21/ 21/...