Page 1: Table Of Contents
We would like to congratulate you on purchasing your new CM-BT bluetooth headset. You have bought a state-of-the-art, highly reliable electronic device. Please read these operating instructions carefully. They explain how to start up the device and describe all the system options and functions.
Page 2: General Information
Obstacles – such as walls or other electronic devices – may cause the connec- tion to experience interference, which can diminish reception quality. The CM-BT headset complies with Bluetooth Specification 1.2 and supports the following profiles: • Headset HSP 1.1 •...
Page 3 5 Status indicator 4 Headphones connection jack 1 Battery cover 2 On/off switch 3 Teleloop connection jack 8 Microphone 6 HI/LO- switch 7 Function key 18 English...
Page 4: First-Time Operation
First-Time Operation Description of the operating elements 1 Battery cover 2 On/off switch • Switched on o Switched off 3 Teleloop connection jack 4 Headphones connection jack 5 Status indicator Warning: Battery low Status indicator flashes blue/red Register mode Blue light flashes every 3 seconds Connection attempt Blue light flashes quickly Connection made...
Page 5: Connecting The Teleloop/Headphones
Connecting the teleloop/headphones The CM-BT headset can be operated in two ways: • Using the teleloop included • Using headphones (not included) To guarantee successful transmission via the teleloop, your hearing aid must be equipped with an integrated tele-coil (T-coil) to transmit the sound informa- tion inductively to your hearing aid.
Page 6: Inserting The Rechargeable Battery
The device runs on one rechargeable "AAA"-type battery. It can also run on a non-rechargeable battery. Where necessary, only use original a replacement rechargeable battery. If you run your CM-BT on a disposable battery, don't place the transmitter onto the CM charger. Ensure that the rechargeable battery are placed the right way around into the battery compartment.
Page 7: Cm Charger
12 V Voltage unit Jack for the power supply unit on the back of the CM charger. Charging cradle for device components 3-pin charging cradle to hold the CM-BT unit LED (red) Standby indicator LED (green) Charge indicator Installation of the CM charger 1.
Page 8: Switching The Headset On/Off
(Position o). How to register the CM-BT headset on a compatible telephone Before you can use the CM-BT with the telephone, it has to be added to the device list in the telephone. To do so, follow the instructions in the telephone operating manual explaining how to activate Bluetooth.
Page 9: Disconnecting The Headset From The Telephone
• Terminate the connection to the CM-BT headset in the telephone’s Bluetooth menu. • Move the CM-BT headset to a position more than ten meters away from the telephone. Please note: You do not have to delete the CM-BT headset from the tele - phone’s list of compatible devices to terminate the connection.
Page 10: Basic Operation
If there is a music player integrated in your telephone, you can also use the CM-BT headset to listen to music. As soon as an incoming call is detected, the music will be interrupted, the CM-BT headset will ring and you can press the function key to answer the call.
Page 11: How To Register The Headset On A Compatible Pc
PC. For more information, refer to the operating instructions for your PC Bluetooth software. 5 Select the CM-BT headset from the list of devices found. To register the headset and establish a connection between the CM-BT headset and the PC, enter the following pass code: “0000”.
Page 12: Appendix
• No changes to the communications system, neither technical nor non-tech- nical, are permitted. • The CM-BT communications system contains small parts that could be easi- ly swallowed. Keep out of the reach of children under 3 years of age.
Page 13: Maintenance And Care
Never use spirits, thin- ners or other organic solvents. Do not set up the CM-BT headset where it will be exposed to full sunlight for long periods. In addition, it must be protected against excessive heat, moisture and severe mechanical shocks.
Page 14: Environmental Notes/Disposal
Environmental notes/Disposal Disposal of used electric and electronic units (applicable in the countries of the Euro pean Union and other European countries with a separate collection system). The symbol on the product or the packaging indicates that this pro- duct is not to be handled as ordinary household waste but has to be returned to a collecting point for the recycling of electric and electronic units.