Download
Share
Print this page
Pride Mobility 24BC2000T-1 Manual
  1. Manuals
  2. Brands
  3. Pride Mobility Manuals
  4. Battery Charger
  5. 24BC2000T-1
  6. Manual

Pride Mobility 24BC2000T-1 Manual

Hide thumbs

Advertisement

Quick Links

B A T T E R Y C H A R G E R M A N U A L
1
0001463–081820

Advertisement

loading

Summary of Contents for Pride Mobility 24BC2000T-1

  • Page 1 B A T T E R Y C H A R G E R M A N U A L 0001463–081820...
  • Page 2 T A B L E O F C O N T E N T S UPG 24V, 2.0A Sealed Lead-Acid Charger Model numbers: 24BC2000T-1, 24BC2000T-2, 24BC2000T-3, 24BC2000T-4 UPG 24V, 3.5A Sealed Lead-Acid Charger Model No: 24BC3500T-4 UPG 24V, 5.0A Sealed Lead-Acid Charger Model No: 24BC5000T-4 UPG 24V, 8.0A...

  • Page 3: Table Of Contents

    T A B L E O F C O N T E N T S High Power Technology 24V, 2.0A Battery Charger for Jazzy Passport ® Model No: HP0060W(L2)-M Metco 29.2V, 2.5A Lithium Ion Charger for Go-Go Folding Scooter ® Model No: NL07C-25HT Intertek 29.4V, 2.5A Lithium Ion Charger for Go-Go...
  • Page 4 SEALED LEAD-ACID CHARGER OWNER'S MANUAL FOR MODEL NUMBER: 24BC2000T-1 24BC2000T-2 24BC2000T-3 24BC2000T-4 UNIVERSAL POWER GROUP 1720 Hayden Drive, Carrollton, TX 75006 Tel: (469) 892-1122 Fax: (469) 892-1123...
  • Page 5 SAVE THESE INSTRUCTIONS This manual contains safety and operating instructions for your charger. Before using your charger, read all instructions for the charger, the battery to be charged, and the product that uses the batteries. WARNINGS • To reduce the risk of injury, charge only 24V, 7-18AH lead acid rechargeable batteries with the charger. Do not charge a non-rechargeable battery.
  • Page 6 DC 500mA Battery Capacity 7 – 18 AH (Suggested) POWER CORD SELECTION Model # Plug Type Input Voltage Power Cord 24BC2000T-1 AC 120V, 60Hz 24BC2000T-2 AC 230V, 50Hz 24BC2000T-3 AC240V, 50Hz 24BC2000T-4 AC 230V, 50Hz Note: Charger comes with one power cord depending on the charger model number. Please refer to the table above for corresponding cord information.
  • Page 7 SAFETY STANDARDS: UU/cUL, CE, GS, c-Tick and SAA THREE STAGE CHARGE CYCLE An integrated circuit monitors and controls both the output voltage and current of tile charger through three separate charge states: A high current, fast charge state: battery charges at 2,000mA fast charge current rate until battery voltage reaches 29.6V.
  • Page 8 OWNER'S MANUAL 24V 3.5A Sealed Lead-Acid Charger Model No: 24BC3500T-4 SAFETY STANDARDS: UL, cUL, CE, GS, C-tick, SAA, FCC FCC STATEMENT This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
  • Page 9 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS: This manual contains safety and operating instructions for your charger. Before using your charger, read all instructions and cautionary markings on the battery charger, and the product using the battery. CAUTION: To reduce the risk of injury, charge only AGM or GEL Sealed Lead-Acid batteries. Other types of batteries may burst, causing personal injury and damage.
  • Page 10 FAULT CODES INDICATION CHARGE/FAULT - Red LED FAULT No batteries - Voltage < 9V Continuous flashing 12 hour charge timed out 1 flash every 3 seconds Battery voltage < 14V 2 flashes every 3 seconds Batteries are connected in reverse polarity 3 flashes every 3 seconds Overvoltage from batteries 4 flashes every 3 seconds Overcurrent from charger THREE STAGE CHARGE CYCLE: An Electronic Control Module (ECM) controls both the output voltage and current of the charger through three separate charge states:...
  • Page 11 TROUBLESHOOTING FAULT CONDITION CAUSE Charging will not start; 1) Batteries not connected Charge/Fault LED not on 2) Battery voltage less than 14V Charge complete; (Green) LED is not on; 1) Charger is too small for batteries Fault (Red) LED is blinking continuously 2) Possible bad battery Charging doesn’t start;...
  • Page 12 OWNER’S MANUAL 24V 5.0A Sealed Lead-Acid Charger Model No: 24BC5000T-4 SAFETY STANDARDS: UL, cUL, CE, GS, C-tick, SAA, FCC FCC STATEMENT This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference.
  • Page 13 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS: This manual contains safety and operating instructions for your charger. Before using your charger, read all instructions and cautionary markings on the battery charger, and the product using the battery. CAUTION: To reduce the risk of injury, charge only AGM or GEL Sealed Lead-Acid batteries. Other types of batteries may burst, causing personal injury and damage.
  • Page 14 FAULT CODES INDICATION CHARGE/FAULT - Red LED FAULT LED is off. No batteries - Voltage < 9V LED - continuous flashing 12 hour charge timed out LED - 1 flash every 3 seconds Battery voltage < 14V LED - 2 flashes every 3 seconds Batteries are connected in reverse polarity LED - 3 flashes every 3 seconds Overvoltage from batteries LED - 4 flashes every 3 seconds Overcurrent from charger THREE STAGE CHARGE CYCLE: An Electronic Control Module (ECM) controls both the output voltage and current of the charger through three...
  • Page 15 TROUBLESHOOTING FAULT CONDITION CAUSE Charging will not start; 1) Batteries not connected Charge/Fault LED not on 2) Battery voltage less than 14V Charge Complete; (Green) LED is not on; 1) Charger is too small for batteries Fault (Red) LED is blinking continuously 2) Possible bad battery Charging doesn’t start;...
  • Page 16 OWNER’S MANUAL 24V 8.0A Sealed Lead-Acid Charger Model No: 24BC8000T-4 SAFETY STANDARDS: UL, cUL, CE, GS, C-tick, SAA, FCC FCC STATEMENT This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference.
  • Page 17 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS: This manual contains safety and operating instructions for your charger. Before using your charger, read all instructions and cautionary markings on the battery charger, and the product using the battery. CAUTION: To reduce the risk of injury, charge only AGM or GEL Sealed Lead-Acid batteries. Other types of batteries may burst, causing personal injury and damage.
  • Page 18 FAULT CODES INDICATION CHARGE/FAULT - Red LED FAULT LED is off. No batteries - Voltage < 9V LED - continuous flashing 12 hour charge timed out LED - 1 flash every 3 seconds Battery voltage < 14V LED - 2 flashes every 3 seconds Batteries are connected in reverse polarity LED - 3 flashes every 3 seconds Overvoltage from batteries LED - 4 flashes every 3 seconds Overcurrent from charger THREE-STAGE CHARGE CYCLE: An Electronic Control Module (ECM) controls both the output voltage and current of the charger through three...
  • Page 19 TROUBLESHOOTING FAULT CONDITION CAUSE Charging will not start; 1) Batteries not connected Charge/Fault LED not on 2) Battery voltage less than 14V Charge Complete; (Green) LED is not on; 1) Charger is too small for batteries Fault (Red) LED is blinking continuously 2) Possible bad battery Charging doesn’t start;...
  • Page 20 Battery Maximizer Lead-Acid Battery Charger Instruction Manual EA1065-P 24 Volt VRLA / SLA / AGM / Gel Fully Automatic SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions.
  • Page 21 INTRODUCTION The Battery Maximizer EA1065-P 24 volt battery charger is a fully automatic, multi- stage full switching charger. It is designed to properly charge VRLA / SLA / AGM / Gel lead-acid batteries without having to worry about overcharging. It may be used in all parts of the world with its advanced universal AC input (110 or 220VAC).
  • Page 22 The charger will begin charging automatically. If the Green Power LED does not illuminate, check the connections. Note that if the battery voltage is less than 9VDC, then the charger will not charge. The batteries may not be connected correctly or have been over- discharged.
  • Page 23 IMPORTANT SAFETY INSTRUCTIONS Rev. F CAUTION: For use with LEAD-ACID batteries only VRLA, SLA, AGM, Gel For indoor use only. WARNING: To reduce risk of fire and electric shock, install in a temperature and humidity controlled indoor area, free from dust and conductive contaminants. Disconnect from AC power before cleaning. Make sure batteries are clean and properly connected.
  • Page 24 Battery Maximizer Lead-Acid Battery Charger Instruction Manual ELECHG1016 3 Amp off-board (Victory 10) EA24030-9C 24 Volt VRLA / SLA / AGM / Gel Fully Automatic SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions.
  • Page 25 INTRODUCTION The Battery Maximizer A24030-9C 24 volt battery charger is a fully automatic, multi- stage full switching charger. It is designed to properly charge VRLA / SLA / AGM / Gel lead-acid batteries without having to worry about overcharging. It may be used in all parts of the world with its advanced universal AC input (110 or 220VAC).
  • Page 26 Battery replacement may be necessary. Have the unit inspected by an authorized service center. INHIBIT FUNCTION The inhibitor pin of output connector will be low level for inhibit function when AC voltage applies to this charger. SPECIFICATIONS Input 100–240 VAC, 50/60Hz Output 24 Volt DC Battery Charger 3A charge current...
  • Page 27 IMPORTANT SAFETY INSTRUCTIONS Rev. F CAUTION: For use with LEAD-ACID batteries only VRLA, SLA, AGM, Gel For indoor use only. WARNING: To reduce risk of fire and electric shock, install in a temperature-controlled and humidity-controlled indoor area, free from dust and conductive contaminants. Disconnect from AC power before cleaning. Make sure batteries are clean and properly connected.
  • Page 28 HIGH POWER TECHNOLOGY (KunShan) INC Battery Charger Instructions HP0060W Series...
  • Page 29 HP006OW BATTERY CHARGER INSTRUCTIONS 1. OPERATING INSTRUCTIONS (1) Make sure the power cord, charger and battery connector are in good condition. (2) Make sure the output voltage of the charger is the same as the connecting battery. (3) Connect the plug of the charger with the battery, and then plug the AC power plug into an outlet.
  • Page 30 Specification of Li-ion Charger (Model NL07C-25HT) DESCRIPTION: NL07C-25HT is a smart charger specially designed for Li-ion battery pack composed cells in series. ELECTRICAL SPECIFICATIONS: 1. Input: I00-240VAC, 50/60 Hz. Output: 29.05V± 0.2V 2.5Adc ± 10% 2. Charger output: The charger is preset by factory for charging 7 cells Li-ion battery pack. Its charging mode: (1) Constant current (CC) mode : at beginning of charging, an 2.5Adc±10% (1(ave)) constant charging current to charge the pack until the pack voltage reaches to...
  • Page 31 MECHANICAL SPECIFICATION: 1. Dimension: 167*4*37 mm. 2. Weight: 410g approx. 3. Charger output: 3-pin connector (Pin 1-Positive; Pin 2-Negative; Pin 3-Negative). 4. AC socket: Standard 2-p oblong. 5. AC cable: National wall plug type upon request. OPERATION PROCEDURES: 1. Attention! Connect charger first to AC power before connecting the battery to the charger. Plug into AC main.
  • Page 32 Specification of Li-ion Charger (MODEL:LS-018C20-2402500) DESCRIPTION: LS–018C20-2402500 is a smart charger specially designed for Li-ion battery pack composed of cells in the series. ELECTRICAL SPECIFICATIONS: 1. Input: 100–240VAC, 50/60 Hz Output; 29.4V ± 0.2V 2.5Adc±10% 2. Charger output: The charger is preset by the factory for charging 7 cells in this Li-ion battery pack. Charging mode: (1) Constant current (CC) mode: at beginning of charging, an 2.5Adc±10% (l(ave)) constant charging current to charge the pack until the pack voltage reaches to...
  • Page 33 MECHANICAL SPECIFICATION: 1. Dimension: 160*86*55 mm. 2. Weight: 510g approx. 3. Charger output: 3-pin connector (Pin 1-Positive; Pin 2-Negative; Pin 3-XXX). 4. AC socket: Standard 2-p oblong. 5. AC cable: National wall plug type upon request. OPERATION PROCEDURES: 1. Attention! Connect charger first to AC power before connecting the battery to the charger. Plug into AC main.

  • Page 34: Aci Super Power 24V, 5.0A

    ACI SUPER POWER ™ Lead-Acid Class II Battery Charger Owner’s Manual Model: ACl245000 24V, 5.0A VALA / SLA / AGM / Gel Cell SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions.
  • Page 35 GENERAL INFORMATION ACl245000 battery charger ls-an automatic, three-stage battery charger. It is designed to properly charge VALA/ SLA /AGM /Gel Cell lead-acid batteries. With optimized algorithm that ensures the batteries receive optimum charging from the delivery of an accurate three-stage charge cycle, ACl245000 charger provides a lasting, safe and complete charge, without risk of over-charging and battery damage.
  • Page 36 SPECIFICATIONS INPUT 100 • 240VAC, 50/60 Hz, 170W OUTPUT OUTPUT 24 VDC, 5.0A DIMENSIONS Length 169.3 mm / 6.67 in Width 136.6 mm / 5.38 in Height 82.5 mm / 3.25 in Weight 0.96 kg / 2.12 lb SAFETY LISTINGS CE / ETL / C-Tick CHARACTERISTICS Universal AC Input...
  • Page 37 IMPORTANT SAFETY INSTRUCTIONS CAUTION For charging VALA, SLA, AGM, Gel/LEAD-ACID battery only Recommended for 18 - 55 Ah battery For indoor use only WARNING AND SAFETY NOTES To reduce the risk of the battery explosion and electric shock: • Follow these instructions and those published by the battery manufacturer and the manufacturer of mobility aid device.

  • Page 38: Battery Charger

    BATTERY CHARGER INSTRUCTIONS - ENGLISH APPEARANCE 1. Power Cord 2. Output Plug to Battery 3. Indicator: - Green Flash: Power On - Orange Flash: Pre-Charge - Orange: Charging - Green & Orange Flash: Charged 80% - Green: Full Charge - Red Flash: Defect SPECIFICATIONS ITEM BATTERY CHARGER (SWITCHING MODE)
  • Page 39 OPERATING INSTRUCTION (1) Make sure the battery charger output voltage is the same as the connecting battery. (2) Plug in the power cord. LED indicator flashes green when AC power on. (3) Connect the battery charger to the battery. (4) Start charging; please refer to 4, LED INDICATION. LED INDICATION (1) Green flash: power on (2) Orange: charging (3) Orange flash: precharge (4) Green & orange flash: charged 80%...

  • Page 40: Battery Charger For Iride Tm Scooter

    HIGH POWER TECHNOLOGY (KunShan) INC Battery Charger Instructions for iRIDE Scooter HP1202L3 (2A/1.5A)
  • Page 41 1. Operating Instructions (1) Make sure the power cord, charger and battery connector are in good condition. (2) Make sure the output voltage of the charger is the same as the connecting battery. (3) Connect the plug of the charger with the battery, and then plug the AC power plug into the electricity outlet.

This manual is also suitable for:

24bc2000t-224bc2000t-324bc2000t-424bc3500t-424bc5000t-424bc8000t-4 ... Show all