Do you have a question about the SDVoE EXT-PROMATRIXUSB and is the answer not in the manual?
Questions and answers
Summary of Contents for KanexPro SDVoE EXT-PROMATRIXUSB
Page 1
Flexible Matrix System transceiver powered by SDVoE w/ USB, POE & RS-232 All Right Reserved MPN: EXT-PROMATRIXUSB VER 1.0...
Page 2
SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, •...
1. INTRODUCTION The KanexPro SDVoE powered Modular Matrix system is the most versatile flexible video distribution solution. The system is composed of transceiver devices that can be configured as either video transmitters or receivers with a simple click of a mouse. The whole system is controlled and configured by a single control module which makes setup a snap.
2. APPLICATIONS • Video, Audio, LAN, IR, and USB extension • Hotel or convention center display • Multi-monitor broadcast • Distributed video matrix system • Distributed video wall system • Remote KVM system control 3. PACKAGE CONTENTS • 1x 4K UHD+ HDMI over IP Transceiver •...
optional IP Master (EXT-PROCTRL) Controller/control software) • Bi-directional IR, RS-232, USB 2.0, and Ethernet extension • Supports a special Simultaneous Mode for USB extension allowing • a host connected to a single transceiver to connect to up to 7 transceivers with USB devices connected (mass storage devices are not supported in this mode) •...
7. - (MINUS) BUTTON: Press to move up or adjust selections within OSD menus. When not in a menu, press to manually toggle between inputs (Receiver Mode only). 8. + (Plus) BUTTON: Press to move up or adjust selections within OSD menus. When not in a menu, press to manually toggle between inputs.
6. IR IN PORT: Connect to an IR Extender to receive IR control signals and extend them to devices connected to a connected transmitter/receiver. Ensure that the remote being used is within direct line-of-sight of the IR Extender. Note: Currently, only 38KHz IR signal extension is supported. 7.
6.4 RS-232 Bypass Pinout 6.5 OSD Menu All functions of this unit can be controlled by using the OSD (On Screen Display) which is activated by pressing the MENU button on the front of the unit. Use the + (PLUS), - (MINUS), and ENTER buttons to navigate the OSD menu.
Page 10
1. Display Information: Enable or disable the Information OSD. 2. Information Timeout: Set the display timeout for the Information OSD. 3. Menu Timeout: Set the display timeout for the OSD Menu. 4. Menu H Position: Set the horizontal position of the OSD Menu. Note: Independent values are saved for Transmitter and Receiver modes.
Page 11
1. HDMI EDID: Select the EDID to send to the HDMI input. This unit provides the following 6 internal EDIDs: FHD (2Ch) 1920x1080p@60Hz (170MHz) LPCM 2.0 8-bit color, LPCM 2.0 FHD (MCh) 1920x1080p@60Hz (170MHz) LPCM 7.1 & 8-bit color Bitstream UHD (2Ch) 3840x2160p@30Hz (300MHz) LPCM 2.0...
Page 12
DEVICE SETTING 2ND LEVEL 3RD LEVEL STATUS TRANSMITTER RECIEVER FAN MODE FOLLOW TEMP ALWAYS ON USB CONTROL MODE HOST DEVICE USB Virtual Hub (USB Device Mode only) Input INPUT 1 (Receiver Mode only) INPUT 2 Local Priority (Receiver mode only) 1.
Page 13
6. Local Priority: Enable or disable the priority auto switch mode for the HDMI input. When enabled, the unit will automatically switch to the HDMI input if a live signal is present. Note: Only available when the unit is in Receiver Mode. INFORMATION 2ND LEVEL 3RD LEVEL...
6.6 Basic AV Extension 6.6.1 Point-to-Point Configuration The most basic extension configuration available is a point-to-point system with a single unit in Transmitter Mode connected directly to a single unit in Receiver Mode. In this configuration the HDMI input on the Transmitter is transmitted to the connected Receiver without modification to the audio or video format.
6.7 Advanced AV Extension 6.7.1 IP Master (EXT-PROCTRL) Controller The IP Master (EXT-PROCTRL) Controller is a hardware solution designed to provide a unified and easy method to access and control all of the transmitters and receivers in a system. It provides a user-friendly, and operating system agnostic, web-based interface allowing easy control over all of the most critical functions within a distribution system.
6.7.2 Configuration Examples When combined with the IP Master (EXT-PROCTRL) Controller, and a 10 Gigabit Ethernet switch, this extension system gains a large number of additional configuration options including: multi-in/multi-out matrix switching with breakaway audio, video wall creation, and a multiview output mode. Audio extraction and embedding is fully controllable.
7. CONNECTION DIAGRAM HDMI Cable LAN Cable Extend up to 120 meters (495 feet) over CAT6a Encoder Mode Decoder Mode Sources Displays EXT-PROCTRL Projector NETWORK SWITCH 10G POE NETWORK SWITCH EXT-PROCTRL EXT-PROMATRIXE XT-PROMATRIX x1 RX in this case x9 RX in this case (for each screen) (for each screen) Multi Viewer...
8. SPECIFICATIONS 8.1 Technical Specifications HDMI Bandwidth 18Gbps Ethernet Bandwidth 10Gbps Input Port 1 x HDMI (Type-A) Output Port 1 x HDMI (Type-A) Bi-directional Port 1 x 10GbE LAN (RJ-45) Pass-through Ports 1 x Stereo Audio (3.5mm) 1 x RS-232 (3-pin Terminal Block) 1 x IR Extender (3.5mm) 1 x IR Blaster (3.5mm) 2 x USB 2.0 (Type A)
Page 24
LPCM Linear Pulse-Code Modulation Media Access Control On-Screen Display Personal Computer SDVoE Software Defined Video over Ethernet Signal-to-Noise Ratio Transmission Control Protocol THD+N Total Harmonic Distortion plus Noise 4K UHD 4K Ultra-High-Definition (10.2Gbps max) 4K UHD+ 4K Ultra-High-Definition (18Gbps max) UHDTV Ultra-High-Definition Television Universal Serial Bus...
Page 25
Remarks: For further assistance or solutions, please contact your local distributor, or email directly to us at support@kanexpro.com...
Need help?
Do you have a question about the SDVoE EXT-PROMATRIXUSB and is the answer not in the manual?
Questions and answers