Summary of Contents for Biological Controls MICROCON EXC7
- Page 1 MICROCON® EXC7 and EXC7-UV User Manual Read and Save these Instructions Manufactured by 749 Hope Road, Suite A- Eatontown, NJ 07724 USA Tel: 800-224-9768, 732-389-8922 Fax: 732-389-8821 www.biologicalcontrols.com 8/19/2010...
- Page 2 Copyright 2010 Biological Controls 8/19/2010...
- Page 3 CAUTIONS IN THIS MANUAL AND ATTACHED TO THE UNIT BEFORE STARTING INSTALLATION OR MAINTENANCE ACTIVITIES. IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE, MAINTENANCE, OR USE CAN CAUSE FIRE, ELECTRICAL SHOCK, OR OTHER CONDITIONS THAT MAY CAUSE PERSONAL INJURY OR PROPERTY DAMAGE. Copyright 2010 Biological Controls 8/19/2010...
- Page 4 Interconnect Cable Assembly Blower Module Filter Module Filter Module Control Panel Copyright 2010 Biological Controls 8/19/2010...
-
Page 5: Table Of Contents
Filter Module .................................13 10.2. Blower Module................................14 SCHEMATICS ................................15 11.1. Typical System 115V Schematic...........................15 11.2. Typical System 230V Schematic...........................15 11.3. Typical System 1/5 HP 2-Speed Motor Schematic .....................16 11.4. Remote Wall Switch Option Schematics........................16 EXC7 PARTS LIST...............................17 Copyright 2010 Biological Controls 8/19/2010... -
Page 6: Introduction
Interconnect Cable Assembly. When a controlled negative room-pressure is required, the system will include a ceiling diffuser and an exhaust control-duct (transition box with damper). Several low voltage (24V) remote power control and monitoring options are available. Copyright 2010 Biological Controls 8/19/2010... -
Page 7: Installation Mechanical
T-bar channels. Four (4) small brackets located on the top of the Filter Module chassis must be used to level and support the weight of the unit using approved cable, wire, or chain hardware. Copyright 2010 Biological Controls 8/19/2010... -
Page 8: Blower Intake Collar-Plate
They can be accessed and installed through the 12” duct opening in the side of the unit. If not, the bulbs can be accessed by removing the HEPA filter. Copyright 2010 Biological Controls 8/19/2010... -
Page 9: Blower To Filter Module Interconnect Cable Assembly
AC power source that will not be interrupted during normal activity. Note that the polarity ) of the power-module 24VDC must be observed as shown in the schematic for proper operation. The module positive (+) wire is marked with a white-ink dashed line. Copyright 2010 Biological Controls 8/19/2010... -
Page 10: Key-Switch (Optional)
For negative-pressure environments (see the System Applications Section), adjust the damper in the transition-box to achieve the desired room-pressure. (Note: A pressure monitor will be necessary for this procedure. Wall mount and portable units are available from Biological Controls.) Copyright 2010 Biological Controls 8/19/2010... -
Page 11: Maintenance Information
The UV lamps require change-out every 8000 hrs (approximately 1 year) of continued use. Log the Hour-Meter readings to determine the UV maintenance schedule. The UV view-port mounted on the control panel will glow blue when the UV bulbs are active. Copyright 2010 Biological Controls 8/19/2010... -
Page 12: Cleaning
When handling a new HEPA filter, hold it by its external frame without touching the media. Temporally place cardboard over the entire room-side face of filter to protect the media during the procedure. Remove the protective cardboard just before the filter clamps are fully tightened. Copyright 2010 Biological Controls 8/19/2010... -
Page 13: Uv Lamp Renewal
Never attempt to replace lighted UV lamps. When changing UV lamps, use approved UV eye and skin protection. UV lamps require renewal every 8000 hours (approx. 1 year) of operation. Check the Hour-Meter Log to determine a routine maintenance schedule. Copyright 2010 Biological Controls 8/19/2010... -
Page 14: System Applications
12 feet and the total duct-rise should not exceed 10 feet. Since the exhaust-air has been filtered it is possible to exhaust directly into an air-return area above a sealed ceiling. Copyright 2010 Biological Controls 8/19/2010... -
Page 15: Room Filtration Only
For units out of warranty, a written purchase order must be issued to Biological Controls prior to the return. The factory will NOT accept and will refuse any merchandise returned without proper authorization. The factory is not responsible for any damage to or loss of merchandise during return shipping. - Page 16 Manufacturer: TEL: 800-224-9768 BIOLOGICAL CONTROLS FAX: 732-389-8821 749 Hope Road Suite A WEB SITE: www.biologicalcontrols.com Eatontown, NJ 07724 Copyright 2010 Biological Controls 8/19/2010...
-
Page 17: Specifications
SPECIFICATIONS 9.1. Filter Module Feature Description 9.2. Blower Modules Copyright 2010 Biological Controls 8/19/2010... -
Page 18: Assembly Figures & Dimensions
ASSEMBLY FIGURES & DIMENSIONS Filter Module 10.1. Copyright 2010 Biological Controls 8/19/2010... -
Page 19: Blower Module
Blower Module 10.2. Copyright 2010 Biological Controls 8/19/2010... -
Page 20: Schematics
SCHEMATICS Typical System 115V Schematic 11.1. Typical System 230V Schematic 11.2. Copyright 2010 Biological Controls 8/19/2010... -
Page 21: Typical System 1/5 Hp 2-Speed Motor Schematic
Typical System 1/5 HP 2-Speed Motor Schematic 11.3. Remote Wall Switch Option Schematics 11.4. Copyright 2010 Biological Controls 8/19/2010... -
Page 22: Exc7 Parts List
1/5 HP wired for 115VAC 50/60 Hz EXC7BM1.20 EXC7-CBLASSY-10 (Standard) 10' Cable Assembly connecting the EXC7 Filter Module to the Blower Module EXC7-CBLASSY-(ft) (Custom Length) Cable Assembly (min 5’max 30’) Installation, Operation& Service Manual (Issue) EXC7 Manual (date) Copyright 2010 Biological Controls 8/19/2010...
Need help?
Do you have a question about the MICROCON EXC7 and is the answer not in the manual?
Questions and answers