During installation, make sure the inlet tube connections and gaskets remain fully engaged to ensure a watertight seal. Shut off the water supply. KALLISTA reserves the right to make revisions in the design of products without notice, as specifi ed in the Price Book. TOOLS AND MATERIALS Plus: •...
Page 3
The centerline of the stud pocket should intersect with the center of the waste outlet. The center of the waste outlet should be exactly 4” (102 mm) from the front edge of the framing. 1206758-2-C Questions? Problems? For additional assistance, please contact KALLISTA’s Customer Service Department at 1-888-4KALLISTA (1-888-452-5547) or kallista.com. 3 of 12...
Page 4
Raise the carriage 8” (203 mm) - 10” (254 mm) high, enough to allow room for a wrench and lag bolts over the feet. Tighten the nuts securing the legs to the carriage. 1206758-2-C Questions? Problems? For additional assistance, please contact KALLISTA’s Customer Service Department at 1-888-4KALLISTA (1-888-452-5547) or kallista.com. 4 of 12...
Page 5
Gently turn the lower locking screw (labeled “Lock”) clockwise until you hear a click to secure the waste pipe. 1206758-2-C Questions? Problems? For additional assistance, please contact KALLISTA’s Customer Service Department at 1-888-4KALLISTA (1-888-452-5547) or kallista.com. 5 of 12...
Page 6
Secure the feet of the carriage to the studs using 2” (51 mm) long (minimum) lag bolts (not supplied). Install the threaded rods several turns into the carriage. 1206758-2-C Questions? Problems? For additional assistance, please contact KALLISTA’s Customer Service Department at 1-888-4KALLISTA (1-888-452-5547) or kallista.com. 6 of 12...
Page 7
If a cast iron elbow is required, make the connections following all applicable codes. 1206758-2-C Questions? Problems? For additional assistance, please contact KALLISTA’s Customer Service Department at 1-888-4KALLISTA (1-888-452-5547) or kallista.com. 7 of 12...
Page 8
Secure the carriage to the support studs using 2” (51 mm) long (minimum) lag bolts (not supplied), one on each side. At the location of the inlet, drill a 2” (51 mm) hole. 1206758-2-C Questions? Problems? For additional assistance, please contact KALLISTA’s Customer Service Department at 1-888-4KALLISTA (1-888-452-5547) or kallista.com. 8 of 12...
Page 9
Install the water supply pipes, following all local codes. Connect the waste pipe following all applicable local codes. 1206758-2-C Questions? Problems? For additional assistance, please contact KALLISTA’s Customer Service Department at 1-888-4KALLISTA (1-888-452-5547) or kallista.com. 9 of 12...
Page 10
Install the fl ush shield in the fl ush valve opening using the four supplied screws. If it is not already installed, install the fl at panel in the fl ush valve opening. 1206758-2-C Questions? Problems? For additional assistance, please contact KALLISTA’s Customer Service Department at 1-888-4KALLISTA (1-888-452-5547) or kallista.com. 10 of 12...
Page 11
Finished Wall Use a utility knife to carefully trim the fl ush shield even with the fi nished wall. 1206758-2-C Questions? Problems? For additional assistance, please contact KALLISTA’s Customer Service Department at 1-888-4KALLISTA (1-888-452-5547) or kallista.com. 11 of 12...
Turn on the water supply and check the fl ow through the hose. Continue to investigate water path for obstructions. Clear any blockages. 1206758-2-C Questions? Problems? For additional assistance, please contact KALLISTA’s Customer Service Department at 1-888-4KALLISTA (1-888-452-5547) or kallista.com. 12 of 12...