Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Foshk HP3000
Summary of Contents for Foshk HP3000
- Page 1 TFT COLORFUL DISPLAY MULTIPLE-CHANNEL WEATHER STATION Operation Manual...
- Page 2 OVERVIEW 1. Inventory of contents 1) Base station 2) Five thermo-hygrometers 4) Power adapter 5) User manual Console Figure 1 Figure 2 Outdoor sensors Figure 3 2. Introduction...
- Page 3 Thank you for your purchase this professional weather station. This device can receive signals up to at most 8 outdoor sensors and. All the sensors measure temperature, humidity, heat index and dew point and transmit to the console and displayed in defined channels. This manual will guide you step-by-step through setting up your device.
- Page 4 Figure 5 4. Insert two AA batteries 5. Wait for seconds until temperature and humidity displayed on the LCD screen of sensors. 6. Verify the correct channel number (CH) and temperature units of measure are on the display, as shown in Figure 6. Figure 6 (1) Temperature (2) Temperature units ((℉or ℃)
- Page 5 display on the display console. 3. Wait 3 minutes or until the outdoor temperature is displayed in the weather station. Do not press any keys before outdoor sensor data received. 3.3 Radio Controlled Clock (RCC) After the remote sensor is powered up, the sensor will transmit weather data for 30 seconds, and then the sensor will begin radio controlled clock (RCC) reception.
- Page 6 Figure 9 1. Graph for Temperature/Dew point/heat index/humidity of sensors. 2. Date and time. 3. Outdoor Temperature/Dew point/heat index/humidity for channel 1 and other channels defined to be displayed in CH1 area in turn. 4. Outdoor Temperature/Dew point/heat index/humidity for channel 2 and other channels defined to be displayed in CH2 area in turn.
- Page 7 Figure 10 Icon Description Graph key Switch to display graph of Temperature/Dew point/heat index/humidity for all sensors Brightness control key Press this key to increase the brightness Brightness control key Press this key to decrease the brightness Menu Key Press this key to enter menu and scroll to different modes 5.2 Setup Mode Under Normal mode, press MENU key once to enter Setup Mode.
- Page 8 Scroll left key Press this key to scroll up/left. Mode key Press this key to enter to next mode CH Area1-5 Scroll to selected channel area, and press key to enter the setting interface as below: Icon Description Scroll right key Press this key to scroll down/up.
- Page 9 For example, press Setup Key of CH Area1 to enter the Area Section interface, you will find temperature of channel 1 is default selected. Move the red dot to choose temperature of channel 5, the temperature and humidity of channel 1 and channel 5 would be displayed on CH1 Area in turn.
- Page 11 Icon Description Scroll down/right key Press this key to scroll down/right. Selection/value increase key Press this key to select parameter and enter the calibration interface. Increase the value during calibration. Value Decrease key Decrease the value during calibration. Resume key Press this key to cancel the calibration and resume the data.
- Page 12 Icon Description Scroll down/right key Press this key to scroll down/right. Selection/value increase key Press this key to select parameter to check according max/min records. Switch on/off alarms and increase the value during alarm setup. Value Decrease key Decrease the value during alarm setup.
- Page 13 Humidity Max/Min interface Dew point Max/Min interface...
- Page 14 Heat index Max/Min interface High/Low alarm of Humidity setting To enter alarm setting interface, you need to select the alarm ON (default OFF): scroll to OFF key before Humidity alarm, and press key to switch on the alarm. Then scroll to Humidity alarm and press key to enter humidity alarm setting mode.
- Page 15 When an alarm condition has been activated, the specific alarm will sound and flash for 120 seconds, the alarm icon will turn to red color (high alarm) or blue color (low alarm). The alarm icon will show on display console until the weather condition doesn’t meet the user set level.
- Page 16 High alarm Red – grey - red Low alarm Blue – grey - blue High alarm & Low alarm both activated Red – grey – blue – grey – red Beep alarm stop grey High/Low alarm of Temperature setting To enter alarm setting interface, you need to select the alarm ON (default OFF): scroll to OFF key before Temperature alarm, and press key to switch on the alarm.
- Page 17 When an alarm condition has been activated, the specific alarm will sound and flash for 120 seconds, the alarm icon will turn to red color (high alarm) or blue color (low alarm). The alarm icon will show on display console until the weather condition doesn’t meet the user set level.
- Page 18 Factory reset: To reset the device to factory initial settings. Clear Max/Min: Clear Max/Min records of specified outdoor sensor. Re-register sensor：If the sensor display “-- --”, please scroll to it and enter to Re-register the sensor. About: Check version information.
-
Page 19: Specification
English: To switch language. Backlight: Set the automatically on/off time spot of back light. And adjust the brightness range. 6. Specification Transmission distance in open field : 100meter max. Frequency 868MHz/915MHz... - Page 20 Temperature measure range: -40 to 60C Resolution 0.1℃ Humidity measuring range: 10% to 99% Humidity accuracy +/-5% under 0-45℃ Alarm duration 120 sec Water proof level IPX3 Measuring interval Outdoor sensor channel 1 Outdoor sensor channel 2 Outdoor sensor channel 3 Outdoor sensor channel 4 Outdoor sensor channel 5 Outdoor sensor channel 6...
Need help?
Do you have a question about the HP3000 and is the answer not in the manual?
Questions and answers