Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Rittal CW 120-S
Summary of Contents for Rittal CW 120-S
- Page 1 Stationary busbar cutting unit CW 120-S 4055.710 Operating instructions...
- Page 2 Foreword Dear Customer, We thank you for choosing our Rittal product. Read these operating instructions carefully before using your new unit for the first time and retain them together with the supplied Product Control Card so they can be consulted when required.
-
Page 3: Table Of Contents
Commissioning ..............8 Cutting busbars ............. 10 Replacing the cutting blade ..........12 Maintenance and inspection ........... 13 Dismantling and disposal ..........15 Contacts ................ 16 Rittal stationary busbar cutting unit CW 120-S We reserve the right to make technical modifications. -
Page 4: Ce Labelling
1 CE labelling CE labelling Rittal GmbH & Co. KG confirms the conformity of the stationary busbar cutting unit with machine directive 2006/42/EC and with EMC directive 2014/30/EU. An appropriate declaration of conformity has been issued. It can be found at the end of this document, on the Rittal Homepage or accompanies the unit as separate document. -
Page 5: Personal Protective Equipment
– Safety work shoes: for all work on the unit – Safety goggles: for all work on the unit – Gloves: for loading and unloading the unit Rittal stationary busbar cutting unit CW 120-S We reserve the right to make technical modifications. -
Page 6: Residual Risks When Using The Unit
"Technical specifications"). Proper usage The "stationary busbar cutting unit CW 120-S" (Model No. 4055.710) is a single- acting high-pressure hydraulic unit for clean cutting copper or aluminium bars with a maximum width of 120 mm and a maximum height of 12 mm. The unit is not suitable for cutting structural steels or tool steels. -
Page 7: Available Accessories
The combination of supporting table (5), side guide plates (6) and retainers (4) ensures a reliable, perpendicular guiding of the busbars. The clamping screws Rittal stationary busbar cutting unit CW 120-S We reserve the right to make technical modifications. -
Page 8: Commissioning
Inspect the mains cable and plug of the hydraulic pump for damage. Do not use the electro-hydraulic pump should there be any damage! Place the unit secure and stable to ensure a safe positioning of the unit. We reserve the right to make technical modifications. Rittal stationary busbar cutting unit CW 120-S... - Page 9 7 Commissioning Note: Rittal recommends that the unit is fastened using the four holes in the frame on a worktable or workbench. Connect the hydraulic hose to the hydraulic connection (fig. 1, 3) and the elec- trical control cable to the electrical connection (fig. 1, 2) of the unit.
-
Page 10: Cutting Busbars
Loosen the clamping levers on the side guide plates (fig. 1, 6) of the supporting table and set the guide plates to the width of the busbar. We reserve the right to make technical modifications. Rittal stationary busbar cutting unit CW 120-S... - Page 11 To extend the service life of the laser, it should be switched off for longer machining pauses (> 10-15 minutes). To switch off the pump, turn the mains switch to the "0" position. Rittal stationary busbar cutting unit CW 120-S We reserve the right to make technical modifications.
-
Page 12: Replacing The Cutting Blade
(2) at the cutting unit so the cutter bar remains at the bottom position. Fig. 6: Dismantling the retainers Dismantle the two retainers (3) and the side protective inspection window (4). We reserve the right to make technical modifications. Rittal stationary busbar cutting unit CW 120-S... -
Page 13: Maintenance And Inspection
The maintenance intervals are classified in accordance with the recommended frequency. Rittal stationary busbar cutting unit CW 120-S We reserve the right to make technical modifications. - Page 14 … Replace the hydraulic hose. Maintenance, inspections and repairs must be performed by qualified electri- cians in accordance with the regulations valid in the associated country. We reserve the right to make technical modifications. Rittal stationary busbar cutting unit CW 120-S...
-
Page 15: Dismantling And Disposal
The "stationary busbar cutting unit" must be properly disposed of or recycled in accordance with the country-specific regulations. Rittal stationary busbar cutting unit CW 120-S We reserve the right to make technical modifications. -
Page 16: Contacts
– Phone: +49(0)2772 505-9052 – E-mail: info@rittal.com – Homepage: www.rittal.com For sales or service requests, please contact your local Rittal organisation which can be found at www.rittal.com/contact. We reserve the right to make technical modifications. Rittal stationary busbar cutting unit CW 120-S... - Page 17 Notes Rittal stationary busbar cutting unit CW 120-S We reserve the right to make technical modifications.
- Page 18 Notes We reserve the right to make technical modifications. Rittal stationary busbar cutting unit CW 120-S...
- Page 19 Notes Rittal stationary busbar cutting unit CW 120-S We reserve the right to make technical modifications.
- Page 20 ◾ Climate Control ◾ IT Infrastructure ◾ Software & Services You can find the contact details of all Rittal companies throughout the world here. www.rittal.com/contact RITTAL GmbH & Co. KG Postfach 1662 · D-35726 Herborn Phone +49(0)2772 505-0 · Fax +49(0)2772 505-2319...
Need help?
Do you have a question about the CW 120-S and is the answer not in the manual?
Questions and answers