Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for CHARGESPOT E15
- Page 1 PRODUCT MANUAL Last Updated: July 4, 2017...
- Page 2 PURPOSE STATED FOR THIS DOCUMENT, SUCH INSTALLER SHOULD IMMEDIATELY NOTIFY CHARGESPOT IN WRITING TO THAT EFFECT AND SHOULD NOT USE THIS DOCUMENT. PRICES AND OTHER TERMS AND CONDITIONS FOR SALE OF CHARGESPOT COMPONENTS TO ANY INSTALLER ARE GOVERNED BY SEPARATE DOCUMENTS ISSUED OR MADE AVAILABLE TO THE...
-
Page 3: Safety Information
Do not use the ChargeSpot with an extension cord or overloaded electrical outlet Do not place or leave metallic objects between the charging surface and device being charged It is recommended that the ChargeSpot be installed to provide 10 cm of separation from persons IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS –... -
Page 4: Fcc & Industry Canada Compliance
FCC & INDUSTRY CANADA COMPLIANCE NOTICE: Changes or Modifications made to this device not expressly approved by ChargeSpot Wireless Power Inc. may void the U.S. FCC and Canadian authorization to operate this device. This device complies with part 15 of the FCC Rules. Operation is subject to the following two... -
Page 5: During Installation
By proceeding with the installation of ChargeSpot components in OEM products, the OEM agrees that: (i) CHARGESPOT is not liable under any theory of contract, tort law, or otherwise for any loss, damage, death, personal injury, special, incidental, or consequential damages, or any other... -
Page 6: Warranty Information
In order to safely install and use CHARGESPOT products and components, full consideration of the work environment (e.g., location of electrical wiring, support members, surface thicknesses, and other electrical and structural components) is required. CHARGESPOT disclaims responsibility for improper use or installation of products or components and use or installation not consistent with the original manufacturer specifications and recommen- dations (if any) for such products or components. - Page 7 The OEM should conduct a “bench test” to verify that all electronic issues are resolved prior to installation: Make sure the ChargeSpot is operational with a Qi-certified or PMA-certified receiver device before being installed Check the Power Supply connection for proper fit 2017 CHARGESPOT WIRELESS POWER INC.
- Page 8 1/2”– #6 Wire Clips Machine Screws Machine Screws Wood Screws Power Adaptor 5 Single-Unit 15 Multi-Unit Power Supply Power Supply 2x Stickers/De- Sparks Decal cals Apple Lightning Placement Tool & mUSB (2 pieces) 2017 CHARGESPOT WIRELESS POWER INC. CONFIDENTIAL 8/13...
-
Page 9: Tooling List
Includes: Battery, Case. Caliper Measuring Length: 6”. Increments: 1/64”. Router jig Provided by ChargeSpot ChargeSpot Decal Provided by ChargeSpot Placement Tool ChargeSpot Test Provided by ChargeSpot Receiver For tooling overviews and set-up please see https://chargespot.wistia.com/projects/sg6zfb9w1v 2017 CHARGESPOT WIRELESS POWER INC. CONFIDENTIAL 9/13... - Page 10 44 - 51mm ( 1.7" - 2" ) 8-32 x 1 ½ " ( not included ) Table 1: Screw Length Selection Based on Substrate Thickness Figure A. ChargeSpot placed in mounting plate 2017 CHARGESPOT WIRELESS POWER INC. CONFIDENTIAL 10/13...
-
Page 11: Installation Instructions
Figure 2a. Measure the table and jig thickness together. that could be damaged. CALIPER ROUTER AFTER INSTALLATION Test the installed ChargeSpot to ensure that it is Figure 1a. underside of table working properly. File these instructions in a safe place and refer to ¼” (6mm) them when performing maintenance or re-installing. - Page 12 ChargeSpot (Figure 2b). DECAL PLACEMENT Remove table surface if possible Figure 5. Power supply jack on the ChargeSpot A er cutting the pocket from the underside Ensure ChargeSpot unit fits into each hole use the ChargeSpot decal placement tool...
- Page 13 If the ChargeSpot transmitter is not flush up within 1 second against the under of the substrate, use a Philips Figure 6b. The screw heads of the ChargeSpot should be head screwdriver to loosen the corresponding placed in the holes of the mounting plate.