Summary of Contents for Vanco Evolution EVOIPLITE
- Page 1 EVO-IP HDMI® OVER IP Transmitter/Receiver Vanco Part Number EVOIPLITE HDMI over IP Transmitter/Receiver www.vanco1.com • 800.626.6445...
- Page 2 DEAR CUSTOMER Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. This product is 100% inspected and tested in the United States to verify HDMI performance parameters.
-
Page 3: Package Contents
INTRODUCTION The Evolution by Vanco EVOIPLITE HDMI over IP Transmitter/Receiver is a complete audio, video, and control product over ethernet system. As a whole, the system has the ability to send multiple sources to multiple displays along with IR and RS232 pass-through, analog and digital audio breakout in TX mode, video up to 1080P@60Hz, with POE up to 100m when connected to a POE enabled switch off of a single Cat6 cable. -
Page 4: Specifications
SPECIFICATIONS HDMI Compliance ............HDMI HDCP Compliance ............Yes Video Bandwidth ............Single-link 225MHz [6.75Gbps} Video Support ............Up to 1080p@60Hz HDMI over UTP transmission [24-bit] ......Full HD (1080p)-100m(330ft) [CAT.X] Audio Support ............Stereo Digital Audio Input TMDS signal ............1.2 Volts [peak-to-peak] Input DDC signal ............ -
Page 5: Panel Description
PANEL DESCRIPTION EVOIPLITE 1. +5V DC: Connect to 5V DC power supply (optional) 2. LED Indicator: Power LED indicator 3. Micro USB: for F/W update 4. Receiver/Transmitter Selection: Sets unit as either a transmitter or receiver [Left]: configures as a receiver [Right]: configures as a transmitter RS-232 (terminal block format): The order of RS-232 pin are TX, RX, GND (from the left to the right): S/PDIF Output (Digital Optical Output) Will only output in TX mode only... - Page 6 PANEL DESCRIPTION EVOIPCTL (Control Box Sold Separtely) 5V Power Port (necessary as this unit requires external power) Status Indicator Light (lights up when communicating with the system) Power Indicator Light (lights up when powered up by included power supply) HDMI OUT (connect to local display to show system IP information) RJ45 Port: Connects to an approved ethernet switch, for a list of approved ethernet switches, please visit www.vanco1.com, under the “downloads and documents”...
-
Page 7: Connect And Operate
Before connecting and setting up EVOIPLITE, please enable settings within your ethernet switch that will allow you get the best performance possible. For additional information on which switches are recommended by Vanco please visit the product page at ww.vanco1.com. Source... - Page 8 Connect power to the EVOIPCTL1 and turn on the ethernet switch. If your ethernet switch is not capable of POE (power over ethernet), connect the provided 5v power supplies to each EVOIPLITE unit. Using a computer that is connected to the same network, type in www.evo-ip.local into a web browser to get to the GUI.
- Page 9 Make sure that all changes and settings are saved and applied 10. Within the SETUP tab, make sure you back up your system by exporting the configuration file to your computer for future reference WHEN USING EVOIPLITE & EVO-IP ON THE SAME NETWORK EVOIPLITE can be on the same network with the EVOIPTX1 and EVOIPRX1 units, so that all EVO-IP products can be accessed under the same GUI.
-
Page 10: Limited Warranty
If repairs are needed during the warranty period the purchaser will be required to provide a sales receipt/sales invoice or other acceptable proof of purchase to the seller of this equipment. The seller will then contact Vanco regarding warranty repair or replacement. -
Page 11: Technical Support
TECHNICAL SUPPORT In case of problems, please contact Vanco Technical Support by dialing 1-800-626-6445. You can also email technical support issues to techsupport@vanco1.com. When calling, please have the Model Number, Serial Number (affixed to the bottom of the unit) and Invoice available for reference during the call. - Page 12 ® Vanco International 506 Kingsland Drive Batavia, Illinois 60510 call: 800.626.6445 fax: 630.879.9189 visit: www.vanco1.com...