Advertisement
Quick Links
Advertisement
Summary of Contents for Lapp Structures YardCraft 12x12 Pavilion
- Page 1 12x12 Pavilion Assembly Manual...
- Page 2 12x12 Pavilion Assembly Manual Congratulations on purchasing your new Pavilion. Thank You for your purchase and Welcome to the YardCraft Famiy. This manual is designed to simplify the assembly process, however we recommend having an experienced carpenter involved in the project. Please read through the entire manual before starting! The Pavilion put together for this manual was a 12x12 Pavilion.
-
Page 3: Parts List
Parts List 2 1/2” Screws 2” Panhead Screws 1 1/4” Screws 3/8”x10 1/2” Bolts, Wash- 3/8”x6” Lag Bolts ers, and Nuts 3 1/8” GRK Lags 3/8”x3 1/2” Threaded Rods 3/8”x4” Bolts with 1” Pancake Screw 3/4” Rubber Waher Screws with Washers & Acorn Washers &... - Page 4 Parts List Continued Post Left Outside Header Piece Right Outside Header Piece Inside End Header Piece Inside Center Header Piece Center Rafter Left Side Fascia Piece Right Side Fascia Piece Left Side Hip Rafter Right Side Hip Rafter Right Side Jack Rafter Left Side Jack Rafter...
- Page 5 Long Purlin Piece Short Purlin Piece Left Side Metal Pieces Right Side Metal Pieces Drip Edge Ridge Clip Ridge Cap...
- Page 6 Inside Center Inside End Header Piece Header Piece Right Outside Left Outside Header Piece Header Piece Fasten the Inside End Header Piece to each Fasten the Left Outside Header Piece to the side of the Inside Center Header Piece with Right Outside Header Piece with 1 1/4”...
- Page 7 Second Post Bracket Align the Post Bracket with the bottom of the Post First Post Bracket Turn the post around and install the second Install the Post Brackets on the bottom of the Post Bracket. Using previous steps, Install the Post.
- Page 8 If Anchoring to Concrete, Use either (2) Tapcon If Anchoring to Wood, Use either (2) 1/4” Screws Screws or (1) 1/2”x4” Powers Wedge Bolt. These or (1) 1/2”x4” Lag. These are not Provided. Follow are not Provided. Follow the Manufactures the Manufactures recommendations on installing recommendations on installing these fasteners.
- Page 9 3/8” Washer 3/8” x6” Lags Using your own 1/4”x6” Drill Bit, Pre-Drill through Using a 9/16” Socket, Turn the 3/8”x6” Lag Through the hole into the Post. the Pre-Drilled hole into the post. Repeat on the opposite side of the Header. 3/8”...
- Page 10 Fasten to the inside of the Header with 3 1/8” GRK Install the Corner Braces. There are 4 Left Hand, and 4 Screws. Right Hand Braces. They are notched and made to fasten on the outside of the post, and the inside of the header as shown.
- Page 11 Install the last 2 Post Boot Pieces as shown. Using Previous steps, Install the Post boots on all the remaining Posts, as shown in previous steps. Left Fascia Board Right Fascia Board You are now ready to assemble the roof Panel. Start by Locating one (1) Left and one (1) Right Fascia Board.
- Page 12 Bevel Cut on the Fascia Align the Center Rafter Bevel cut with the top of the Center Rafter Fascia Be sure to align the Bevel cut on the Fascia with Measure from the Center Rafter out to the end of the Fascia Boards.
- Page 13 Do not Fasten Here now Left Hip Rafter Left Jack Rafter Fascia Install the Left Jack Rafter. Center the Jack Rafter on Install the Right Jack Rafter the same way as shown in the previous steps for the Left Jack the Pre-Drilled Holes in the Fascia and fasten with Rafter.
- Page 14 3 Rafter Bracket Locations Bracket is Flush with outside of Fascia Fasten the Rafter Bracket to the Fascia and Rafter Install the rest of the Rafter Brackets at the Center with 2” Pan Head Screws. Rafter and Jack Rafter Locations. 3”...
- Page 15 Second Piece First Piece Install the second Drip Edge. Push against the first Fasten the second Drip Edge Piece with 1” Drip Edge as shown. Pancake Screws through Pre-Drilled Holes. Ridge Clip Make Flush Center Rafter Locate and place the Ridge Clip onto the Hip Make the Ridge Clip flush with the end of the Rafter.
- Page 16 After all 4 Roof Panels are assembled, You are ready to install the Roof Panels on top of the Header and Post assembly. Assembly three (3) more Roof Panels, using the previous steps shown. Align with Headers This is how your Pavilion should look with the First Install the Hip Rafter Brackets.
- Page 17 Lift the first Roof Panel in Place. Place the Hip Rafter of the Roof Panel into the Hip Rafter Bracket. Hip Rafter Hip Rafter 2 Screws into Rafter 2x4 Roof Prop Fasten your own 2x4 into the Center Rafter with Place both Hip Rafters Against the Hip Rafter 2 1/2”...
- Page 18 Rafter Bracket Locations Fasten the rest of the Rafter Brackets to the Prepare the 3 1/2” Threaded Rods. Place a 3/8” Header with 2” Panhead Screws. Washer and one (1) Acorn Nut on one end of the 3 1/2” Threaded Rod. Prepare all the 3 1/2” Thread- ed Rods before going to the next step.
- Page 19 3 1/2” Threaded Rod Locations Insert another 3 1/2” Threaded Rod into the other 3 1/2” Threaded Rod Locations Pre-Drilled Hole in the Hip Rafters, as shown in previous step. Hip Rafter 3/8”x4” Bolt And Washer Hip Rafter Bracket Insert a 3/8”x4” Bolt with a 3/8” Washer into the Hip Place a 3/8”...
- Page 20 Install the rest of the Roof Panels using the Locate the Roof Cap Assembly. fasteners as shown in the previous steps. Remove the 3/8” Nut and Washer. Also Remove the Wood Block. Install the Roof Cap Assembly in through the peak Slide the Roof Cap through the hole between the of the Roof Panels.
- Page 21 Roof Cap This is what your Roof Cap should look like at Install the Fascia Corner Brackets. this point. Push the Fascia Corner Brackets against the Install the Fascia Corner Brackets on each Corner, Fascia both ways. Slide it in between the Fascia and as shown in previous steps.
- Page 22 Align this point of the Metal with the splice in Drip Edge 3/4” Rubber Washer Screws Align the metal with the splice in the Drip Edge as Align the Metal With the Drip Edge. Fasten into shown here. Pre-Drilled Holes with 3/4” Rubber Washer Screws. Screw Locations Keeping the Metal Aligned with the Drip Edge,...
- Page 23 Screw Locations Screw Locations Align the Metal Piece with the Drip Edge and Install the next Right Side Metal piece as shown Fasten through Pre-Drilled holes with 3/4” Rubber in the previous steps Washer Screws. Screw Locations Install the Smallest Right Side Metal Piece. Install the next Left Side Metal Piece.
- Page 24 This piece overlaps on top. Screw Locations Slide this piece under the other piece Slide the smallest Left Side Metal Piece into Install the Metal on the remaing 3 sides, as shown place, as shown in the previous steps. in the previous steps. Ridge Clip Ridge Cap Locate the Ridge Cap.
- Page 25 Fasten the block to each Rafter with 2 1/2” Screws. Place the 3/8” Washer and 3/8” Lock Nut onto the Bolt. Tighten just enough to pull the Roof Cap snug against the Metal Roof on top. YardCraft.com Info@YardCraft.com 191 Jalyn Drive New Holland PA 17557 1-844-442-1615...