Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for SAMsync C2D900+
Summary of Contents for SAMsync C2D900+
- Page 1 User Manual C2D900+ Smallest pBTX Desktop...
- Page 2 C2D900+ is a high quality, highly scalable basis for your computing needs. You will find that the C2D900+ System has the following advantages Ultimate small and quiet C2D900+ is designed in the size that just enough for pBTX motherboard and LFX power supply unit; no space wasted inside the chassis.
- Page 3 Copyright Copyright © SAMSYNC Corporation 2005. All right reserved. Disclaimer: SAMSYNC Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use this product.
- Page 4 WARNING: This equipment is designed for connection to a grounded (earthed) outlet. The grounded type plug is an important safety feature. To reduce the risk of electrical shock, damage to your equipment, or loss of data, do not disable this feature. General Guidelines ♦...
- Page 5 To reduce the risk of fire, use at least No. 26 AWG wire for the telecommunication line cord. Always disconnect all telephone lines & all power cords from the wall outlet before servicing or disassembling this product. And, refer it for servicing to qualified service personal under the following conditions: a.
- Page 6 Electrical Restrictions WARNING: This equipment is designed for connection to a grounded (earthed) outlet. The grounding type plug is an important safety feature. To reduce the risk of electrical shock, damage to your equipment, or loss of data, do not disable this feature. Power Cord Set Requirements The power cord set (appliance coupler, flexible cord, and wall plug) you received with the computer meets the requirements for use in the country where you purchased the...
- Page 7 5. Danish Lithiumbatteri- Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kum ske med batteri af samme fabrikat og type. Lever det brugte batteri tilbage til leverandoren. 6. Norwegian Ekspolsjonsafe ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabriknten.
- Page 8 Television antenna connectors protection (for system TV tuner card) External television antenna grounding If an outside antenna or cable system is to be connected to the product, make sure that the antenna or cable system is electrically grounded to provide some provide some protection against voltage surges and static charges.
- Page 9 cable shield to the grounding system of the building, as close to the point of cable entry as practical. TV Antenna The TV antenna supplied with any TV Tuner module is intended for Indoor use only. Please do not use your TV Tuner module outdoors.
-
Page 10: Table Of Contents
Table of Contents Chapter1 Unpacking Checklist:......................11 Chapter2 System Overview Front Panel..................... 12 Rear Panel ..................... 13 Chapter3 Assembling / Disassembling Removing the Case Cover ................16 Removing of Hard Disk Rack ................. 17 Removing of ODD & Card Reader Frame............18 Removing the VGA Card................ -
Page 11: Chapter1
Before unpacking the C2D900+ System, prepare a suitable workspace for your computer. Provide a steady, level and clean surface, near an electrical wall outlet. Also ensure that the computer has enough space around it to allow for airflow, especially at the rear of the computer near the fan. -
Page 12: Chapter2
Front Panel The features in the front panel are shown in Figure 2.1, and are described as following. Figure 2.1 Power switch: Let’s turn the C2D900+ System on or off. When power on, this LED embedded in Power switch will light blue. If the button is held down for one second, the unit will enter Suspend mode, and if held down for four seconds, unit power will switch off. -
Page 13: Rear Panel
Assembling / Dissmebling IEEE1394 Connector 1394 devices can be connected via these ports. Air Inlet This inlet allows air inside or outside chassis to be inhaled and exhaled for better air-flow. ODD device: Insert DVD-ROM into this drive for enjoying multimedia data. 8-in-1 Card Reader: Allows users to access and read a variety of memory cards directly from front panel. - Page 14 Line In jack (blue): Connect audio sources such as tape players to this jack for recording on your computer or playback through the Line Out device. Line Out jack (green) Connect audio devices such as headphones or speakers to this jack. Microphone jack (pink): Plug the microphone into this jack for recording or voice-control functions.
- Page 15 Assembling / Dissmebling Chassis Lock: A hardware security mechanism, when you place the switch in lock position, the chassis cover cannot be opened. Kensington Lock: A hardware security mechanism, which locks the chassis to prevent hardware from being stolen. Pad Lock: A hardware security mechanism, which can lock up the chassis with lock to prevent being opened.
-
Page 16: Chapter3
Removing the Case Cover CAUTION: C2D900+ is design 100% tool less with a special disassemble knob. Please reference to this lable to open the chassis. Lay the unit flat face the rear panel of the unit. Switch the Chassis Lock to unlock cover position, as shown in Figure 3.1 Figure 3.2 Figure 3.1 iii. -
Page 17: Removing Of Hard Disk Rack
Assembling / Dissmebling Removing of Hard Disk Rack Before removing the whole hard disk rack from the main body, please disconnect the flat cable and power cord of the hard disk, as shown in Figure 4.1, and Figure 4.2. Figure 4.1 Figure 4.2 Switch the Chassis Lock to HDD unlock position, as shown in Figure 4.3. -
Page 18: Removing Of Odd & Card Reader Frame
Removing of ODD & Card Reader Frame Remove the front cover with disengaging metal tab that hook on bottom and move it forward to open it. Figure 5.1 ii. Before removing ODD & Card Reader frame from the main body, you must first disconnect the card reader connector, SATA port and power connector, as shown in Figure 5.2 Figure 5.2... -
Page 19: Removing The Vga Card
Assembling / Dissmebling iii. Hold up the shield plate (as indicated by below drawing circle) and pull forward, you may totally opened the ODD & card reader rack, as shown in Figure 5.3. Figure 5.3 Removing the VGA Card Lift up the VGA board shield plate from the main braket, as shown in Figure 6.1. Figure 6.1... -
Page 20: Removing The Power Supplier
Disengage metal tab that stepped with main bracket as indicated in step1, and slightly move the VGA board to right side as indicted in step 2 to unhook the board from staple. Figure 6.2 Perform the above steps in reverse order to install the VGA card. Removing the Power Supplier Pull up the switch to unlock the power supplier, as shown in Figure 7.1. -
Page 21: Installing/Uninstalling The Hard Disk Drive
Assembling / Dissmebling Figure 7.2 Installing/Uninstalling the Hard Disk Drive (Only for Office / Premium SKU) Hook your hands inward onto the plastic holder (as indicated in below drawing step 1) and then lift it upward from the hard disk rack (as indicated in below drawing step 2), as shown in Figure 8.1. -
Page 22: Installing/Removing The Cpu
Pull the plastic holder outward a bit for removing the hard disk, as shown in Figure 8.2. Figure 8.2 iii. Fix the hard disk rack in position by simply placing it back to main frame, as shown in Figure 8.3. Figure 8.3 Installing/Removing the CPU Remove the CPU heat sink before removing the CPU. - Page 23 Assembling / Dissmebling CPU_Fan Sys_Fan Connector Connector Power Connector Figure 9.1 Unscrew the heat sink from motherboard, as shown in Figure 9.2. Figure 9.2 iii. Orient the CPU with the socket, place the CPU on socket, it should slide into place without the use of force.as shown in Figure 9.3.
- Page 24 Figure 9.3 iv. Pull down the socket lever and click it into its latch at the side of the socket, as shown in Figure 9.4 above, to lock the CPU in position. Figure 9.4 Place the heatsink back to motherboard, and screw each side of the heatsink, there are 4 holes in total, as shown in Figure 9.5 below.
-
Page 25: Installing Foot Stand
Assembling / Dissmebling Installing Foot Stand The footstand is intended for the C2D900+ to stand securely in the upright position. Please assemble it on the chassis, as shown in Figure 10.1 and Figure 10.2 Figure 10.1 Figure 10.2 C2D900+ System with the foot stand which can keep the C2D900+ up and stable during use. -
Page 26: Appendix
Product Features • Slim Super Multi x 1 Drive bays • 3.5” standard HDD drive x 1 • Card Reader drive x 1 • Switches: Power Button Front Panel • Creative Window: USB port x 2 IEEE1394 port x 1 Line out jack x 1 Microphone jack x 1 •... -
Page 27: Technical Specifications
Assembling / Dissmebling Technical Specifications • 320mm (D) x 290mm (H) x 85mm (W) Dimensions • Standard LFX 220W with PFC Power Supply F/F • Socket 775 Slots & Sockets • DIMM Sockets x 2 • PCI Express X16 Slots x 1 •... -
Page 28: Motherboard Placemenet Chart
Motherboard Placemenet and Specification... - Page 29 Assembling / Dissmebling Project Name PTC-Q965 - Type Socket 775 processor - Model Smithfield (95W) / Conroe (65W) - Vendor Intel - VRM Mainstream FMB (65W) FMB 2006 Mainstream: FMB(06B)、65W Option: FMB(05B) 、130W - FSB 1066/800/533 MHz Chipset - Vendor Intel - North Bridge Intel Broadwater Q965...
- Page 30 - Audio/Gameport - LAN (RJ45) RJ45 - Modem (RJ11) - 1394 - Diagnosis LED LAN Activity, Follow SAMSYNC default Front I/O - Front USB Port (2x5) 2 ports/2 x Pin Header - Front Memory Stick - Front Audio(2x5) Yes (Mic-in, Headphone) HD Audio...
- Page 31 Assembling / Dissmebling - Front Panel (2x5) - HDD Activity LED - ON/OFF/Suspend LED on Front Panel - Single/Dual Color LEDs definition - PCIe Pin header - Jumpers CLR_CMOS (1-2: Normal, 2-3: Clear CMOS) - LPC (2x7) for BIOS debug ITP/XDP 1 (not stuff) debug...