Related Manuals for Toro 79216
Summary of Contents for Toro 79216
- Page 1 Form No. 3329-283 48in Snow Blade TimeCutterE Z Riding Mower Attachment Model No. 79216—Serial No. 230000001 and Up Operator’s Manual Original Instructions (EN, GB) Register your product at www.Toro.com...
-
Page 2: Table Of Contents
Authorized Service Dealer or Toro Customer Service and have the model and Caution signals a hazard that may cause minor or serial numbers of your product ready. Figure 1 illustrates... -
Page 3: Installation
Flat washer, 3/8 inch Flange nut, 3/8 inch Lift mount assembly Installing the snow blade Lift rod Clevis pin Cotter pin, 3/4 inch Shoulder bolt, Operator’s manual Read before installing the snow blade Registration card Fill out and return to Toro... -
Page 4: Removing The Mower
Removing the Mower 7. Remove the hairpin cotter and washer at the mower leveling brackets (Fig. 3) on each side of the mower. Note: Retain all parts for installing the mower on the 8. Slide the brackets off of the mounting pin. traction unit in the future. - Page 5 4. Attach the skids to both sides of the blade with 4 carriage bolts (3/8 x 1 inch), flat washers (3/8 inch), and locknuts (3/8 inch) (Fig. 5). 2, 3, 4 m–5559 Figure 5 m–5567 1. Skid 3. Flat washer, 3/8 inch Figure 6 2.
-
Page 6: Preparing The Traction Unit
Preparing the Traction Unit 6. Remove the front bolt and nut in the base of the gas tank plate and set aside (Fig. 9). 1. Move the lift lever into the lowest position to install 7. Remove the upper screw in the gas tank plate and the lift arm (Fig. -
Page 7: Installing The Snow Blade
12. Secure the rear spring mount to the gas tank plate Note: The snow blade is in position when the rear shaft of using a bolt (1/4 x 3/4 inch) and lock nut (1/4 inch) the frame assembly has moved past the lift arm and is (Fig. - Page 8 Connecting the Lift Rod 5. Remove the foot plate to access the existing holes in the traction unit frame (Fig. 14). 1. Move the lift rod into position beneath the traction unit and above the frame assembly (Fig. 15). m–7048 Figure 15 1.
-
Page 9: Operation
Adjusting the Blade Angle Operation There are five positions for the side to side angle of the Important This snow blade should be used for blade. To change the blade angle, perform the following plowing snow only. procedure: 1. Raise the blade. Caution 2. -
Page 10: Setting The Blade Height
Setting the Blade Height Adjusting the Blade Trip Springs Set the operating height using the following procedure. The blade trip springs can be mounted in four positions. 1. Move the lift lever into the second lowest position. The top hole provides the greatest scraping pressure and 2. -
Page 11: Maintenance
Maintenance Recommended Maintenance Schedule Maintenance Service Maintenance Procedure Interval Grease the channel pivot. 25 hours Oil the linkages. Grease the channel pivot. Oil the linkages. Yearly/Storage Service Examine the scraper for wear and replace if necessary. Paint any chipped surfaces. Caution If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. -
Page 12: Reversing The Scraper
Reversing the Scraper Removing the Blade Periodically inspect the scraper blade for wear. Reverse Note: Retain all parts for installing the snow blade on the the scraper blade when it becomes worn and before the traction unit in the future. working surface contacts the housing. -
Page 13: Storing The Blade
5. Paint all scratched or bare metal surfaces. Paint is available from your Authorized Toro Dealer. 6. Store the blade in a clean, dry garage or storage area. 7. Cover the machine to protect it and keep it clean.