Royal Well Red Leaf RW2362 Manual

ycarbonate glazing: note the cover is on the outside of the
Do not yet remove the protective covers on the
nels.

Before You Start

polycarbonate glazing: note the cover is on the outside of the

Assembly Instructions

panels.
emble the back and side frames, and front braces (parts A, Montagehandleiding / Instructions de montage /
Please check that all components are present and read through
C2 & C3) using the large screws (H) and the pre-drilled
Assemble the back and side frames, and front braces (parts A, these instructions carefully.
Montageanleitung / Manual
Wooden growhouse
es in the frame (See Fig 1).
C1, C2 & C3) using the large screws (H) and the pre-drilled
Assembly
holes in the frame (See Fig 1).
Red Leaf
the base plates (G) on the underside of two corners as
1. Check all screws are tight in the ready-made frame sections
uired using screws (J). Fix the base plates (G) on the underside of two corners as
but avoid over-tightening.
required using screws (J).
d the shelves (K) to the shelf supports.
Before You Start
2. Do not yet remove the protective covers on the
Add the shelves (K) to the shelf supports.
polycarbonate glazing: note the cover is on the outside of the
90 L x 50 W x 37/45 H cm
ce the lid (B) in position so that the hinges are at the back
Please check that all components are present and read through
W
panels.
H
Place the lid (B) in position so that the hinges are at the back
d are facing downwards. Line up the lid with the frame
these instructions carefully.
L
and are facing downwards. Line up the lid with the frame
es and hold firmly whilst attaching the hinges to the back 3. Assemble the back and side frames, and front braces (parts A,
Assembly
sides and hold firmly whilst attaching the hinges to the back
Nr. C1, C2 & C3) using the large screws (H) and the pre-drilled
nel (A) using screws (I) (see Fig 3).
panel (A) using screws (I) (see Fig 3). holes in the frame (See Fig 1).
1. Check all screws are tight in the ready-made frame sections
1
assemble the lid support arms:
but avoid over-tightening.
4. Fix the base plates (G) on the underside of two corners as
To assemble the lid support arms:
Pass the washers over bolts (F) and insert the bolts, from
required using screws (J).
2. Do not yet remove the protective covers on the
a. Pass the washers over bolts (F) and insert the bolts, from
the outside, through the slots in the support arms and
2
polycarbonate glazing: note the cover is on the outside of the
the outside, through the slots in the support arms and
5. Add the shelves (K) to the shelf supports.
into the pre-drilled holes in the sides (C). Screw in part
panels.
into the pre-drilled holes in the sides (C). Screw in part
way to secure them (see Fig 5).
6. Place the lid (B) in position so that the hinges are at the back
3 3. Assemble the back and side frames, and front braces (parts A,
way to secure them (see Fig 5).
and are facing downwards. Line up the lid with the frame
C1, C2 & C3) using the large screws (H) and the pre-drilled
The wing bolt can be tightened when the lid is in the
sides and hold firmly whilst attaching the hinges to the back holes in the frame (See Fig 1).
b. The wing bolt can be tightened when the lid is in the
4
required position.
panel (A) using screws (I) (see Fig 3).
required position.
4. Fix the base plates (G) on the underside of two corners as
required using screws (J).
ach the doors (D) in the same way as the lid in point 6 7. To assemble the lid support arms:
Attach the doors (D) in the same way as the lid in point 6
a. Pass the washers over bolts (F) and insert the bolts, from
ove, lining up the doors with the frame and attaching with
5. Add the shelves (K) to the shelf supports.
above, lining up the doors with the frame and attaching with
the outside, through the slots in the support arms and
ews (I) (see Fig 5).
screws (I) (see Fig 5).
6. Place the lid (B) in position so that the hinges are at the back
into the pre-drilled holes in the sides (C). Screw in part
and are facing downwards. Line up the lid with the frame
way to secure them (see Fig 5).
ach one door latch (P) to the centre of the top bar so that
Attach one door latch (P) to the centre of the top bar so that
sides and hold firmly whilst attaching the hinges to the back
atches both doors and the other to the outside of one
it catches both doors and the other to the outside of one
panel (A) using screws (I) (see Fig 3).
b. The wing bolt can be tightened when the lid is in the
or as shown.
door as shown.
required position.
7. To assemble the lid support arms:
a. Pass the washers over bolts (F) and insert the bolts, from
8. Attach the doors (D) in the same way as the lid in point 6
0. To complete the assembly, peel off the protective sheet from
complete the assembly, peel off the protective sheet from
the outside, through the slots in the support arms and
above, lining up the doors with the frame and attaching with
the polycarbonate panels and site the Growhouse in good
polycarbonate panels and site the Growhouse in good
into the pre-drilled holes in the sides (C). Screw in part
screws (I) (see Fig 5).
light but out of prolonged fierce sunlight. Use the corner base
way to secure them (see Fig 5).
ht but out of prolonged fierce sunlight. Use the corner base
plates to peg or bolt down the Growhouse if extra security
tes to peg or bolt down the Growhouse if extra security
9. Attach one door latch (P) to the centre of the top bar so that
b. The wing bolt can be tightened when the lid is in the
is required.
it catches both doors and the other to the outside of one
equired. required position.
door as shown.
8. Attach the doors (D) in the same way as the lid in point 6
Care & maintenance
are & maintenance
above, lining up the doors with the frame and attaching with
10. To complete the assembly, peel off the protective sheet from
screws (I) (see Fig 5).
the polycarbonate panels and site the Growhouse in good
Extra coatings of wood preservative will prolong the life of
ra coatings of wood preservative will prolong the life of
light but out of prolonged fierce sunlight. Use the corner base
the product but be sure to use one that is harmless to plants.
9. Attach one door latch (P) to the centre of the top bar so that
product but be sure to use one that is harmless to plants.
plates to peg or bolt down the Growhouse if extra security
it catches both doors and the other to the outside of one
Avoid constant contact with wet soil by mounting the frame is required.
door as shown.
oid constant contact with wet soil by mounting the frame
on bricks, slabs or wooden battens.
10. To complete the assembly, peel off the protective sheet from
Care & maintenance
bricks, slabs or wooden battens.
the polycarbonate panels and site the Growhouse in good
elpline Number
light but out of prolonged fierce sunlight. Use the corner base
• Extra coatings of wood preservative will prolong the life of
ine Number
plates to peg or bolt down the Growhouse if extra security
the product but be sure to use one that is harmless to plants.
you have any problems or queries with this product please call our helpline on
is required.
ave any problems or queries with this product please call our helpline on
• Avoid constant contact with wet soil by mounting the frame
44 (0)1406 372227 between the hours of 9am to 5.30pm Monday to Friday.
Care & maintenance
1406 372227 between the hours of 9am to 5.30pm Monday to Friday.
on bricks, slabs or wooden battens.
• Extra coatings of wood preservative will prolong the life of
Helpline Number
the product but be sure to use one that is harmless to plants.
If you have any problems or queries with this product please call our helpline on • Avoid constant contact with wet soil by mounting the frame
+44 (0)1406 372227 between the hours of 9am to 5.30pm Monday to Friday. on bricks, slabs or wooden battens.
Helpline Number
If you have any problems or queries with this product please call our helpline on
+44 (0)1406 372227 between the hours of 9am to 5.30pm Monday to Friday.
x Nr.
1
5
1 6
1
7
1
8
3
1
Gardman Limited, High Street, Moulton, Spalding, Lincolnshire PE12 6QD
Gardman Limited, High Street, Moulton, Spalding, Lincolnshire PE12 6QD
5
Gardman Limited, High Street, Moulton, Spalding, Lincolnshire PE12 6QD
Gardman Limited, High Street, Moulton, Spalding, Lincolnshire PE12 6QD
8
Parts & Fittings Supplied
Parts & Fittings Supplied
RW2362
x Nr.
A
1
1 B
C
1
D
1
E
F
7
2
1
08896
x
8
M5x50
2
M3x40
4
M3x20 (zwart)
2
4
M5x60
2
4
6