Subscribe to Our Youtube Channel
Related Manuals for EINHELL Expert TE-TS 1825 U
Summary of Contents for EINHELL Expert TE-TS 1825 U
- Page 1 TE-TS 1825 U Original operating instructions Table Saw - . t : . r - . I : . r Anl_TE_TS_1825_U_SPK7.indb 1 21.01.13 09:17...
- Page 2 21 17 - 2 - Anl_TE_TS_1825_U_SPK7.indb 2 Anl_TE_TS_1825_U_SPK7.indb 2 21.01.13 08:51 21.01.13 08:51...
- Page 3 27 28 41 40 39 38 13 15 41,36 39,36 - 3 - Anl_TE_TS_1825_U_SPK7.indb 3 Anl_TE_TS_1825_U_SPK7.indb 3 21.01.13 08:51 21.01.13 08:51...
- Page 4 41,36 41,36 - 4 - Anl_TE_TS_1825_U_SPK7.indb 4 Anl_TE_TS_1825_U_SPK7.indb 4 21.01.13 08:51 21.01.13 08:51...
- Page 5 39 35 39,36 40,36 40,36 40,36 40,36 40,36 40,36 39,36 - 5 - Anl_TE_TS_1825_U_SPK7.indb 5 Anl_TE_TS_1825_U_SPK7.indb 5 21.01.13 08:51 21.01.13 08:51...
- Page 6 3-5 mm - 6 - Anl_TE_TS_1825_U_SPK7.indb 6 Anl_TE_TS_1825_U_SPK7.indb 6 21.01.13 08:51 21.01.13 08:51...
- Page 7 45° - 7 - Anl_TE_TS_1825_U_SPK7.indb 7 Anl_TE_TS_1825_U_SPK7.indb 7 21.01.13 08:52 21.01.13 08:52...
- Page 8 - 8 - Anl_TE_TS_1825_U_SPK7.indb 8 Anl_TE_TS_1825_U_SPK7.indb 8 21.01.13 08:52 21.01.13 08:52...
- Page 9 Caution - Read the operating instructions to reduce the risk of injury Wear ear-muff s. The impact of noise can cause damage to hearing. Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials.
-
Page 10: Safety Regulations
25. Strut for length extension table Important! 26. Connecting plate for guide rails 27. Stop rail for angle stop cautions must be observed to avoid injuries and 28. Angle stop damage. Please read the complete operating 29. Push stick instructions and safety regulations with due care. 30. -
Page 11: Proper Use
• Splitter Please note that our equipment has not been de- • Saw blade guard signed for use in commercial, trade or industrial • Stop rail (parallel stop) applications. Our warranty will be voided if the • Parallel stop machine is used in commercial, trade or industrial •... -
Page 12: Technical Data
4. Technical data Keep the noise emissions and vibrations to a minimum. • a i l Mains voltage......230-240 V ~ 50Hz king order. Power P ....S1 1500 W S6 40% 1800 W • a i l . y l Idle speed n ........6,000 min •... - Page 13 6. Assembly 6.2.2 Width extension table (Fig. 17-18) • Loosely fasten the width extension table (8) to the saw table using the Allen screws (38) and Important. Always screw together the connections the washers (37). Use the rear holes closer to which have self-locking nuts (see.
-
Page 14: Operation
6.4 Fitting the saw blade guard (Fig. 1, 22) condition before you begin working with the • Fit the saw blade guard (4) in the oval hole saw again. (y) in the splitter. Fasten the saw blade guard using the screw (x) and tighten the screw only enough to allow the saw blade guard to move 7. - Page 15 8. Operation on the purpose. • The parallel stop is set at right-angles to the guide rail at the factory. It can be readjusted Important!! • using two Allen screws (in the parallel stop). After every new adjustment we recommend you to make a trial cut in order to check the 7.3.2.
-
Page 16: Replacing The Power Cable
10. Cleaning, maintenance and 8.1.3. Cutting very narrow workpieces (Fig. 31) ordering of spare parts • Be sure to use a push block when making longitudinal cuts in very narrow workpieces Always pull out the mains power plug before star- with a width of 30 mm and less. -
Page 17: Disposal And Recycling
11. Disposal and recycling The equipment is supplied in packaging to pre- vent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. -
Page 18: Warranty Provisions
Warranty provisions Einhell Australia o ment of the equipment in accordance with the overview below. Statutory guarantee claims are unaff ec- ted. Defect with regard to material or 24 months construction Wear parts* V-belt, carbon brushes, table 6 months insert, push stick mediate defect (24 hours after purchase / date on the bill) * Not necessarily included in the scope of delivery! - Page 19 The guarantee provided in this Guarantee Certificate is given by Einhell Australia Pty Limited ACN 134 632 858 of 6/166 Wellington Street, Collingwood, Victoria (Telephone number 1300 922 271) (Einhell Express Guarantee). CERTIFICATE GUARANTEE Dear Customer, All of our products undergo strict quality checks. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee certificate.
- Page 20 Wartungsheft_Benzinmaeher_BS_SPK7:_ 06.09.2012 17:20 Uhr Seite 28 EH 03/2013 (01)
Need help?
Do you have a question about the TE-TS 1825 U and is the answer not in the manual?
Questions and answers