Summary of Contents for Ejoin Charger 22kW
- Page 1 Charger 22kW ejoin Charger 7kW ejoin Wallbox 22kW ejoin Wallbox 7kW Manual Copyright © 2019 ejoin. s.r.o. - All rights reserved 1/24...
- Page 2 Copyright This document and information contained herein are the intellectual property of ejoin s.r.o. (hereinafter the ‘Author’), based in the Slovak Republic and subject to copyright laws. The Author reserves all right to reproduce and distribute this document. No part of it may be reproduced, copied, or processed in any way without the express permission of the Author.
-
Page 3: Contact Information
Contact Information Address: ejoin s.r.o., Hviezdoslavova 1168, 018 63 Ladce, Slovakia E-mail: info@ejoin.eu Internet: http://www.ejoin.eu Info Line: +421,424,111,111 Current contact information and contact points for other EU countries are available on the Author’s website (see above). 3/24... -
Page 4: Introductory Information
Introductory Information Congratulations on your purchase of the charging station. We believe that its use will bring you a lot of positive experience with charging your electric car. During the development of the station we made sure that its operation was as simple and safe as required by the applicable EU- and world- wide standards and legislations. - Page 5 Who Can Install the Charging Station? Since the charging station is an electrical device that operates under voltages hazardous to human health, and whose top cover has to be removed during installation exposing the live parts inside, it is essential that a qualified electrical engineer performs the installation with a valid professional license in electrical engineering.
- Page 6 Pedestal Charger 6/24...
- Page 7 Wallbox Charger Figure What Are the Power Supply Requirements? The charging station can be plugged to a three-phase power supply unit of 3x400V/ 230V/50Hz only via 3P+N+PE connection, which means that in addition to the L1, L2, and L3 three-phase wiring, a neutral (N) and protective earthing (PE) conductor must be supplied separately.
- Page 8 What Equipment Is Required to Install the Charger? Mandatory Equipment PH2 Screwdriver (for screwing the charger’s lid) Screwdriver flat 4.0 (for screwing lead wires onto the terminal board) Screwdriver long, type depending on the bolt used Miscellaneous Equipment Screwdriver flat 3.0 (for screwing signal wires onto the terminal block) Metering instrument to make a safe detection of AC supply voltage of 400V/230V/50Hz.
- Page 9 When Can I Start Using the Charger? The charger can be used once all the installation steps have been performed successfully; however, please note that before the final commencement, it is required to obtain an authorization that the system is fit for purpose from an electrical engineer with a valid license (Electrical Inspector).
- Page 10 Charger Station Assembly Warning and General Information Before installation, make sure that the power cord is not live. In addition, prevent other people from handling the switchgear of the upstream power cord to avoid accidental start-up. Remove any and all people from the area that could compromise the safety of anyone involved, such as kids, people with disabilities, the elderly, people suffering from mental disorders that are at a risk of unpredictable behaviour, people under the influence of alcohol, psychotropic substances, or narcotic...
- Page 11 Instructions - 1. Pedestal Installation Lead the power and communication lines through holes in the pedestal, Mount the pedestal on an assembled concrete base, fix it firmly and ground it (by connecting the grounding conductor and terminal - e.g. of the SP 1 type - to the ground nut).
- Page 12 the control unit (CCU1) and tighten the yellow-green protective conductor to the cabinet lid (which you disconnected in step 2). 8. Screw the lid onto the charging station. Before that, however, check the sealing rubber that must be inserted and not twisted in its groove inside the charger’s lid, whose both end points must slightly overlap and be placed from the bottom of the charger.
- Page 13 Red colour - continuous or flashing - indicates an error. Inform the station owner of this situation We recommend that you try to charge your vehicle at another ejoin charging station to identify the source of the error (station or car).
- Page 14 Turn it on again once you re-assemble the lid on the charging station. If the red light is on continuously, contact ejoin to arrange further actions. If the red light is flashing, turn off the power supply, remove the lid, and make sure that the right connector with wires leading to the X2 terminal is connected to the BI1 residual current monitor.
- Page 15 Servicing To maintain the highest safety standards and avoid personal injuries and damage to adjacent property, it is necessary to service the charging station at regular intervals. Some of the listed actions may only be performed by a person with a valid license in the given field, and they can be done during a regular inspection.
-
Page 16: Warranty
(as indicated on the receipt). The warranty can be claimed directly at the ejoin company, which will contact you to arrange further actions. The manufacturer reserves the right to reject warranty and shall not be held... -
Page 17: Product Designation
Afterwards, contact your vendor or the original manufacturer and arrange further actions. !!! Never try to repair the equipment by yourself!!! Product Designation All ejoin Charging Stations bear a label (Product Label) in line with the following template: 17/24... - Page 18 Regular Inspection Specific Instructions The charging station must undergo regular inspections and testing in line with the applicable standards and regulations by a person possessing a mandatory license and qualification. Information contained in this section are for professionals only. Power Cable Insulation Resistance Test In a voltage-free state, switch off the FI1 residual current circuit breaker and the FA1 circuit breaker.
-
Page 19: Technical Information
Technical Information Mechanical Information Working Position Vertical Assembly Pedestal Wallbox Vertical Means of Anchorage 4x Screws Charging Cable Placement Winded Around the Charging Station Charging Station Height Height Between 1 - 1.5m Adjacent Objects Minimum Distance At Least 20cm From Edges Instrument Cabinet Material Aluminium Minimum Post-Installation IP Protection... - Page 20 Earthing Recommendation: SP 1 Terminal Attached to the Pedestal Power Specifications Power Supply System 22kW Version: 3x400V/230V/50Hz TN-C-S/TN-S/TT/IT 7kW Version: 230V/50Hz TN-C-S/TN-S/TT/IT Power Supply Connection Type 22kW Version: 3P+N+PE 7kW Version: 1P+N+PE Supply Voltage Tolerance Supply Voltage Frequency Tolerance Maximum Charging Current / Power 22kW Version: 32A/22kW 7kW Version:...
- Page 21 breaking capacity in line with the properties of the power system. Breaking Capacity (If Applicable) Integrated Circuit Breaker Properties and Rated Current (If Applicable) Protection Class Integrated Electricity Meter (If Included, the Type May Vary) Electricity Meter Type EASTRON SDM630-Modbus V2 Meter Certificate CE, MID-Compliant Meter Settings...
- Page 22 Modbus Output (RS485) Output to X3 Terminal (If Applicable) Data Sheet, Manual, Communication Protocol Meter Documentation Specifications - Available at the Manufacturer’s Website Charging Remote Switch (If Applicable) Connection Two-Wire (Relay Coil Controls) on X3 Terminal Working Voltage / Current 24V/13mA Single-Core Relay Coil Diode Integrated;...
- Page 23 Final Information Warning According to STN EN 61851-1 Pursuant to STN EN 61851-1, it is forbidden to use an extension cord or a secondary cable set to the charging cable. Charger Station Disposal To protect the environment, the charging station shall not be disposed of along with the municipal waste.
- Page 24 Country of Origin Information The ejoin charging stations are products that have been designed and manufactured in the Slovak Republic (EU). 24/24...