1. Manuals
  2. Brands
  3. DARTSLIVE Manuals
  4. Game Console
  5. DARTSLIVE3
  6. Instruction manual

DARTSLIVE DARTSLIVE3 Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

BEFORE USING THE PRODUCT, BE SURE TO READ
THE FOLLOWING:
● Perform work in accordance with the instructions herein stated.
Instructions for work are explained by paying attention to the aspect of accident
prevention. Failing to perform work as per the instructions can cause accidents.
In the case where only those who have technical expertise should perform the
work to avoid hazardous situation, the instructions herein state that the technical
personnel should perform such work.
● Always turn off the power before working on the machine.
Be sure to turn off the power and unplug the power cable before carrying out any
work that requires direct contact with the interior of the product. If the work is to
be performed in the power-on status, this manual always states so.
● Be sure to ground the earth terminal.
This product is equipped with the earth terminal. When installing the product,
make sure that the earth wire is grounded, and connect the terminal to the wire.
Unless the product is grounded appropriately, people can be subject to an electric
shock. After performing repair, etc. for the control equipment, ensure that the earth
wire is firmly connected to the control equipment.
● Ensure that the power supply used is equipped with an earth leakage breaker.
Using a power supply which is not equipped with the earth leakage breaker can
cause a fire when earth leakage occurs.
● Specification changes not designated by DARTSLIVE are not allowed.
The parts of the product include warning labels for safety, covers for personal
protection, etc. It is very hazardous to operate the product by removing parts and/
or modifying the circuits. Doing so may cause fire or electric shock. Should doors,
lids and protective parts be damaged or lost, refrain from operating the product,
and contact your product retailer.
DARTSLIVE shall not be held responsible for any accidents or compensation for
damage to a third party, resulting from the specifications not designated by
DARTSLIVE.
● Be sure to check for electrical specifications.
Ensure that the product is compatible with the power supply voltage and
frequency requirements of the location.
The product has a nameplate on which electrical specifications are described.
Using any electrical specifications different from the designated specifications can
cause a fire and an electric shock.
● Install and operate the product in places where appropriate lighting is available,
allowing warning labels to be clearly read.
To ensure safety for the customers, labels and printed instructions describing
potentially hazardous situations are applied to places where accidents can be
caused. Ensure that where the product is operated has sufficient lighting allowing
the warnings to be read. If any label is peeled off, apply it again immediately.
Please place an order with your product retailer.
● Be sure to adjust the monitor properly.
Do not operate the product leaving on-screen flickering or blurring as it is. Using
the product with the monitor not properly adjusted may cause dizziness or a
headache to the players and the people around them.
BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING:
i

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DARTSLIVE3 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for DARTSLIVE DARTSLIVE3

  • Page 1 DARTSLIVE shall not be held responsible for any accidents or compensation for damage to a third party, resulting from the specifications not designated by DARTSLIVE. ● Be sure to check for electrical specifications. Ensure that the product is compatible with the power supply voltage and frequency requirements of the location.
  • Page 2 INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION Normally, at the time of shipment, DARTSLIVE products are in a status allowing for usage immediately after transporting to the location. Nevertheless, an irregular situation may occur during transportation. Before turning on the power, check the following points to ensure that the product has been transported in a satisfactory status.

  • Page 3: About This Instruction Manual

    ABOUT THIS INSTRUCTION MANUAL This manual provides information on the operation of the software of this product DARTSLIVE3 and explains it in detail. Note that the shapes illustrated in the photos and pictures in this manual may be different from the actual unit.

  • Page 4: Definition Of Site Maintenance Personnel Or Serviceman

    Definition of Site Maintenance Personnel or Serviceman WARNING Procedures not described in this manual or marked as to be carried out by “Site Maintenance Personnel” or “Serviceman” should not be carried out by personnel without the necessary knowledge and skills. Work carried out by unqualified persons may cause serious accidents, including electrocution. For safety reason, if there is no one with knowledge or skill, ask your product retailer to carry out necessary operation. Part replacement, maintenance and inspection, and handling of abnormalities should be performed by Site Maintenance Personnel or Serviceman. This manual instructs especially dangerous work to be performed by Serviceman with expert knowledge.

  • Page 5: Warning Signs

    Warning Signs Make sure you fully understand the meaning of and notes on the warning signs indicated on this manual and the cabinet, and operate the product in proper and safe manner. Explanations that require particular attentions are classified and specified as DANGER, WARNING, or CAUTION, depending on severity of the potential hazard.

  • Page 6: Table Of Contents

    TABLE OF CONTENTS BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: ABOUT THIS INSTRUCTION MANUAL Definition of Site Maintenance Personnel or Serviceman Warning Signs TABLE OF CONTENTS Overview 1 - 1 Name of Parts 1 - 2 Overview 1 - 3 Components How to Play 2 - 1 How to Operate 2 - 1 - 1 Procedure to Start a Game ■...

  • Page 7: Table Of Contents

    4 - 2 Initial Setup / Activation of New Machine 4 - 3 Activation for Taking Over Registration (From Old I/O Board to New I/O Board) Maintenance Menu 5 - 1 Device Settings ■ 5 - 1 - 1 Monitor Settings 5 - 1 - 2 Select Camera ■ 5 - 1 - 3 Select Sensor ■ 5 - 1 - 3 - 1 Target Sensor 5 - 1 - 3 - 2 Impact Sensor 5 - 1 - 3 - 3 Speed Sensor 5 - 1 - 3 - 4 Card Reader Sensor...
  • Page 8 5 - 6 - 2 Online Settings ■ 5 - 6 - 2 - 1 Change Registered Shops 5 - 6 - 2 - 2 Cancel Network Service 5 - 7 Machine Info Troubleshooting 6 - 1 Overview of Network 6 - 1 - 1 Network Structure ■...

  • Page 9: Overview

    1 Overview For details on the dart machine other than software, such as cabinets and components, see another document, "DARTSLIVE3 INSTRUCTION MANUAL". 1 - 1 Name of Parts Upper monitor Player camera / Target camera Target Target sensor (Full bit sensor)

  • Page 10: Overview

    1 - 2 Overview "DARTSLIVE3" has a function to interconnect shops (location where dart machine is installed), DARTSLIVE CARD (hereinafter, IC card), customers (mobile phones and PCs), and "TouchLive". It has elements to provide more enjoyable darts experience by using the network.

  • Page 11: Components

    1 - 3 Components DARTSLIVE CARD (hereinafter, IC card): Using IC card, you can view and manage personal data stored on the "DARTSLIVE Server" (hereinafter, server). You can manage score information such as flights and ratings, stats, and number of wins and loses with one card.

  • Page 12: How To Play

    2 How to Play 2 - 1 How to Operate You can select the buttons on the screen by touching it. 2 - 1 Fig. 01 2 - 1 - 1 Procedure to Start a Game ■ STEP Insert the IC card into the card reader. To play doubles, stack two cards together and insert them into one reader.

  • Page 13: Using Ic Card

    In addition, you can register and authenticate various data in cooperation with the client machine (hereinafter, machine). ・ You can check data by accessing the member site in "DARTSLIVE" website (from PC or mobile phone).
  • Page 14 SINGLES Insert the cards into the slot at the top of the card reader. There are four slots to insert IC card. They can support up to eight cards by stacking two cards together. In singles mode, they are P1, P2, P3, and P4 in order from the left. When the machine recognized the IC card, the name of the player appears at the bottom of the screen.
  • Page 15 You can check the data by inserting IC card and selecting "CARD DATA" after "INFO" on the home menu. The following data stored on the server are available: nickname, name, home shop, rating, flight, stats, RANGE (mm), CORK (mm), and data for DARTSLIVE APP Play Data.

  • Page 16: Help

    2 - 3 Help Description of Games ■ Images of the games have magnifying glass icon. When you touch the image, the description of the game appears. Magnifying glass icon 2 - 3 Fig. 01 2 - 3 Fig. 02 How to Play...

  • Page 17: Game Settings And Optional Game Settings

    2 - 4 Game Settings and Game Option Setting 2 - 4 - 1 Selecting Game ■ When you select a category in the home menu, the game selection screen appears. Select the game you want to play and tap NEXT. Swiping the screen gives you the same effect as tapping NEXT.
  • Page 18 2 - 4 - 3 Game Option Setting ■ When you tap GAME OPTION, it will open the setting screen. GAME OPTION 2 - 4 - 3 Fig. 01 IN : Specify the first target to hit in the game. OPEN：No specific target to hit first.
  • Page 19 ＜ Availability of Option Settings for Each Game ＞ CRICKET MEDLEY ● ● ● ● BULL ● ● CUT THROAT ● THROWING ORDER ● FULL LEG ● MANUAL CORK ● ● ● 2 - 4 - 3 Fig. 03 * MANUAL CORK setting is only available in PvP for two players or two teams. 2 - 4 - 4 Handicap Setting ■...

  • Page 20: Game Menu

    2 - 5 Game Menu When you tap the game menu button displayed on the touch screen monitor, the item window appears. Game menu 2 - 5 Fig. 01 2 - 5 - 1 Game Menu ■ Game Rules： You can check the rules of the game you are playing. Back to the Prev Player：...
  • Page 21 2 - 5 - 2 Darts Position Correction in Game Result ■ When you tap the result menu button displayed on the touch screen monitor, the window for Darts Position Correction function appears. Result menu 2 - 5 - 2 Fig. 01 2 - 5 - 3 Darts Position Correction in MEDLEY LEG Result ■...

  • Page 22: Preparation For Starting Up Online

    3 Preparation for Starting up Online To use DARTSLIVE3 online (using a network), you need to prepare the network environment in advance. In addition, you need to register (application and review) the shop. Contact DARTSLIVE Co., Ltd. for details on how to register the shop.

  • Page 23: Connecting To Network / Normal Connection

    Wait about one minute, and turn on the power at ③ . * If you do not turn on their power in correct order, "DARTSLIVE3" will not be updated properly. * You can power on ③ "DARTSLIVE3" in any order.

  • Page 24: Connecting Multiple Units To Network / Using Hub

    When connecting five or more "DARTSLIVE3", you should prepare a HUB. When using a HUB, connect the router and the HUB with a LAN cable. You will connect the router and "DARTSLIVE3" via HUB. Turn on their power in order of ① , ② , ③ , and ④ .

  • Page 25: Checking Connection Status With Router

    If it does not lit up, check the connection of the LAN cable, and then condition of the network. LAN： While it is connected to "DARTSLIVE3", the indicators LAN 1 to 4 lit up or blink. The numbers correspond to each of the connected "DARTSLIVE3"...
  • Page 26 ・ Check the connection of LAN cable between the router and HUB. ・ HUB may be freezing. Restart it. ● All "DARTSLIVE3" in all areas do not come online. ・ Check the indicator on the router. If it is not lit, restart the router.

  • Page 27: Starting Up New Machine Online (Initial Setup)

    4 Starting up New Machine Online (Initial Setup) IMPORTANT Do not turn off the power when it is downloading data. It may cause a failure. ＜ Operation at Machine Startup ＞ If the machine is connected online, it checks for the latest program and data at startup. When there is a download progress bar at the bottom of the screen as shown below, it is downloading the data.

  • Page 28: What Is Activation

    Registered Dealer ID： ID issued by DARTSLIVE Co., Ltd. at the time of dealer registration. Dealer PASS (PIN) ： PIN issued by DARTSLIVE Co., Ltd. at the time of dealer registration. Registered Shop ID： Shop ID provided to you when setting up the network connection.

  • Page 29: Initial Setup / Activation Of New Machine

    4 - 2 Initial Setup / Activation of New Machine Execute procedure to register and set up a new "DARTSLIVE3" in the initial state and make it available for online use. STEP Connect "DARTSLIVE3" to the network and power it on.
  • Page 30 STEP The dealer name and shop name to register appear on the screen. Check the information to register. Tap "Yes" to complete the registration. 4 - 2 Fig. 03 STEP Tap "OK" to move to the home menu in the online mode. 4 - 2 Fig.

  • Page 31: Activation For Taking Over Registration

    " DA R T SL I V E3" to " DA R T SL I V E", " DA R T SL I V E2" to " DA R T SL I V E3", " DA R T SL I V E3" to "DARTSLIVE2", "DARTSLIVE" to "DARTSLIVE2", or "DARTSLIVE2" to "DARTSLIVE", since they have different I/O boards.
  • Page 32 If you turn on the power with the cable disconnected from the router, it starts in offline mode and you cannot perform activation registration. Contact DARTSLIVE Co., Ltd. for more detail. ＜ To Change the Registered Setting ＞...

  • Page 33: Maintenance Menu

    Happy Hour Credit setting. Be careful when installing dart machines with different price settings in the same shop. ● Changes to the settings in the maintenance menu will take effect when you tap "End" after making the changes. ● The I/O board connected to "DARTSLIVE3" is exclusive for "DARTSLIVE3". It cannot be used for "DARTSLIVE2", "DARTSLIVE", or "TouchLive". Operations of the system maintenance menu include the operations inside the machine while power is on. Pay more than enough cautions as careless work may result in electric shock or short circuit.
  • Page 34 Launching the Maintenance Menu Stand at the front of the cabinet. Open the right side door and press "TEST" button. TEST button 5 Fig. 01 Touch monitor Insert coin ON/OFF Maintenance items Exit 5 Fig. 02 5 Fig. 03 Switch operation monitor Switch monitor Insert coin ON/OFF：...

  • Page 35: Device Settings

    5 - 1 Device Settings You can perform setting and adjustment on the devices. ・Monitor - Refer to "5-1-1 Monitor Settings". ・Camera - Refer to "5-1-2 Select Camera". ・Sensor - Refer to "5-1-3 Select Sensor". ・Target - Refer to "5-1-4 Target". ・Light - Refer to "5-1-5 Light".
  • Page 36 5 - 1 - 2 Select Camera ■ 5 - 1 - 2 Fig. 01 Target Camera： You can check the display of the camera (5-1-2 Fig. 03) aimed at the target (the board) by performing a display test (5-1-2 Fig. 02). 5 - 1 - 2 Fig.

  • Page 37: Target Sensor

    5 - 1 - 3 Select Sensor ■ You can make adjustment on the sensors. ・Target sensor - Refer to "5-1-3-1 Target Sensor". ・Impact sensor - Refer to "5-1-3-2 Impact Sensor". ・Speed sensor - Refer to "5-1-3-3 Speed Sensor". ・Card reader sensor - Refer to "5-1-3-4 Card Reader Sensor". 5 - 1 - 3 Fig.

  • Page 38: Impact Sensor

    Calibration： Make adjustments so that the target sensor properly sense the position where the dart hits on the target. Follow the instructions in order to perform the test. Note：Start work with nothing stuck in the target. Use a straight tip. Be sure to check with one tip.

  • Page 39: Speed Sensor

    5 - 1 - 3 - 3 Fig. 02 Machine Environment Test： Test whether the speed sensor works properly at the shop where the DARTSLIVE3 is installed. STEP You should run the air conditioner installed in the shop at high mode.
  • Page 40 5 - 1 - 3 - 3 Fig. 06 STEP If it is an inappropriate location, try the following: Action to Take： Move the installation location of DARTSLIVE3 by 5 cm or more, and perform the Machine Environment Test again. Maintenance Menu...

  • Page 41: Card Reader Sensor

    5 - 1 - 3 - 4 Card Reader Sensor You can check whether the card reader is working properly or not. When you insert the card into the card reader, the displayed word "NO CARD" changes to the number of the ID card.

  • Page 42: Light

    Reaction Test for Membrane Switch： You can perform reaction test by pressing at each area on the target. If the positions are displayed on the touch screen monitor when you press the target, the devices and wiring of the input system are normal.

  • Page 43: Side Led

    5 - 1 - 5 - 1 Side LED You can test the display and adjust the brightness on the side LED. 5 - 1 - 5 - 1 Fig. 01 Display Test： You can perform the display test of the side LED. The side LED switches in order of red, green, blue, and white.

  • Page 44: Standing Navi Led

    5 - 1 - 5 - 2 Standing Navi LED Brightness Adjustment： You can adjust the brightness of the Standing Navi LED. You can adjust it in steps 0 to 20. 0 turns it OFF. The smaller the number, the darker it gets; the larger the number, the brighter it gets.

  • Page 45: Number Led

    5 - 1 - 5 - 4 Number LED Brightness Adjustment： You can adjust the brightness of the Number LED on the target (the board). You can adjust it in steps 0 to 3. 0 turns it OFF. The smaller the number, the darker it gets; the larger the number, the brighter it gets.

  • Page 46: Coin Credit Administration 38

    5 - 2 Coin Credit Administration You can check and configure various coin credit settings. ・ Counter Management - Refer to "5-2-1 Counter Management". ・ Insert Coin Settings - Refer to "5-2-2 Insert Coin Settings". ・ Coin Chute Credit / Free Play Settings - Refer to "5-2-3 Coin Chute Credit / Free Play Settings". ・...

  • Page 47: Counter By Credit

    5 - 2 - 1 - 1 Counter by Credit You can check the Counter by Credit from the day the machine was started and the number of Counter by Credit from the date the counter was reset. Reset： It resets the counter to zero that has been counted from the day it was last reset until today.

  • Page 48: Reset All Counter Administration Data

    5 - 2 - 1 - 3 Reset All Counter Administration Data You can reset all functions at once which can be reset in both Counter by Credit and Counter by Credit. 5 - 2 - 1 - 3 Fig. 01 5 - 2 - 2 Insert Coin Settings ■...
  • Page 49 5 - 2 - 3 Coin Chute Credit / Free Play Settings ■ Coin Chute Credits： You can set the number of credit to increase for each coin inserted. Free Play Settings： You can activate Free Play Settings by turning it ON. * It automatically turns OFF Insert Coin Settings while Free Play Settings is enabled.

  • Page 50: Time Settings

    5 - 2 - 5 - 1 Game Credit Settings Settings for Happy Hour Free Play： You can enable Free Play during Happy Hour by turning this ON. Credit Settings for all： By turning this ON, it will reflect the Credit Settings for all during Happy Hour.

  • Page 51: Game Settings

    5 - 3 Game Settings You can configure if to display specific games, change the number of rounds and the number of Back to the Prev Player/ Darts Position Correction. ・Settings by Category / by Game - Refer to "5-3-1 Settings by Category / by Game". ・Basic Settings - Refer to "5-3-2 Basic Settings".

  • Page 52: Advertise Settings 44

    * In some cases, Language Settings is not available. 5 - 6 Network Settings In Network Test on DARTSLIVE3, you can test the status of network operation. In Online Settings, you can change registered shops and cancel the network services.

  • Page 53: Change Registered Shops

    5 - 6 - 1 Network Test ■ When it is operating normally, it displays "OK" on the item. When it is having an error, it displays "ERROR" on the item having the error. 5 - 6 - 1 Fig. 01 5 - 6 - 2 Online Settings ■...

  • Page 54: Cancel Network Service

    It displays names of the dealer, the old shop, and the new shop. Verify the changes. Tapping "Yes" will complete the change of registered shop. (5-6-2-1 Fig. 02) After changing the registered shop, DARTSLIVE3 needs to be restarted. Please restart DARTSLIVE3. (5-6-2-2 Fig. 03) 5 - 6 - 2 - 1 Fig.

  • Page 55: Machine Info

    Machine ID ： Identification unique to the machine. Sub Machine ID ： Sub-identification unique to the machine. Shop Name： Name of the shop where DARTSLIVE3 is installed. Date and time： Current date and time. * The time is automatically adjusted when online.

  • Page 56: Troubleshooting

    6 Troubleshooting If the network does not operate normally, take the following steps first. * Before turning off the power of "DARTSLIVE3", be sure to restart the modem and router. Not doing so may clear the stored data. * If the network is operating normally, online symbol appears at the network operation status.
  • Page 57 Restart the modem. ERROR. Check the wiring again for disconnected connectors. Restart the router. * Do not turn off the power of "DARTSLIVE3". It may clear the stored data. * The line may be under construction. Contact your ISP. It displays ROUTER Check the wiring for disconnected connectors.

  • Page 58: Overview Of Network

    6 - 1 Overview of Network 6 - 1 - 1 Network Structure ■ The network connection for "DARTSLIVE3" is structured as the following. Modem Router DARTSLIVE3 6 - 1 - 1 Fig. 01 6 - 1 - 2 Supplemental Terminology ■...
  • Page 59 6 - 1 - 3 Network Operation Status ■ At the top right corner on the screen of the "DARTSLIVE3", you can check the status of the network. Operation status are classified into the following six types. Network operation status 6 - 1 - 3 Fig.

  • Page 60: Network Trouble

    ■ Is the LAN indicator on the router lit on? → If it is not lit, the cable between the router and "DARTSLIVE3" is not connected properly. 　Is the cable from the router connected to the "DARTSLIVE3"? Is it firmly connected? Is the cable from the "DARTSLIVE3"...
  • Page 61 　Are the power of the modem and other devices connected? ■ Is the LAN indicator on the router lit on? → If it is not lit, the cable between the router and "DARTSLIVE3" is not connected properly. 　Is the cable from the router connected to the "DARTSLIVE3"? Is it firmly connected? 「s the cable from the "DARTSLIVE3"...
  • Page 62 For general inquiries: DARTSLIVE Support Desk https://www.dartslive.com * Please note that this support desk is not accepting inquiries regarding the machine and the parts. Please contact the retailer for such inquires. DARTSLIVE Co.,Ltd. Sumitomo Fudosan Osaki Garden Tower, 1-1-1 Nishi-Shinagawa, Shinagawa-ku, Tokyo 141-0033, Japan http://www.dartslive.com/corp/jp/contact/...

Table of Contents