Precision ULTRA 900 Homeowner's Manual

Smart wi-fi garage door opener

Hide thumbs

Table of Contents

Quick Links

Homeowner's Manual

Smart Wi-Fi Garage Door Opener

DC motor with LED lighting and belt or chain-drive rail

Battery Back-Up Capable (Ultra 900)

Battery Back-Up Included (Ultra 900B)

• Please read this manual and included safety information carefully.

• After the opener is installed and working properly, use your smart phone

to download and activate the Linear Smart Garage Door app (page 11).

ULTRA 900 / 900B

WARNING

To reduce the risk of injury to persons - Use this

opener only with sectional residential overhead doors.

Do not use on one piece or swing doors.

Important Safety Information ............................... page 1

Using the Garage Door Operator ........................ page 2

Manual Disconnect .............................................. page 3

Testing the Safety Beam ..................................... page 4

Adjusting the Open and Close Limits .................. page 5

Automatic Door Force Setup ............................... page 6

Safety Reversal System Test ............................... page 6

Programming Remote Controls ........................... page 7

Programming Keypad Codes .............................. page 8

Setting Up the Wall Station ................................. page 9

Maintenance ...................................................... page 11

Installing/Replacing the Battery Back-Up .......... page 12

Troubleshooting ................................................. page 13

Warranty ............................................................ page 14

Installer's Contact Information:

Manufactured by:

Nortek Security & Control LLC

USA & Canada (800) 421-1587 & (800) 392-0123

www.nortekcontrol.com

10019144 B

Table of Contents

Summary of Contents for Precision ULTRA 900

Page 1: Table Of Contents
Manufactured by: Nortek Security & Control LLC DC motor with LED lighting and belt or chain-drive rail USA & Canada (800) 421-1587 & (800) 392-0123 Battery Back-Up Capable (Ultra 900) www.nortekcontrol.com Battery Back-Up Included (Ultra 900B) WARNING To reduce the risk of injury to persons – Use this opener only with sectional residential overhead doors.
Page 2: Important Safety Information
IMPORTANT SAFETY INFORMATION Important Safety Information will CAUTION WARNING follow the words CAUTION and This type of warning note is This type of warning note is used WARNING which are used to used to indicate the possibility to indicate possible mechanical emphasize potentially hazardous of damage to the garage door or hazards that may cause serious...
Page 3: Using The Garage Door Operator
USING THE GARAGE DOOR OPERATOR Opening the Door 1 With the door in view, press the wall station’s UP/DOWN ARROW button, the button assigned WALL STATION to the opener on the remote control, or enter a PRESS THE valid access code and press on a wireless WALL STATION’S keypad.
Page 4: Manual Disconnect
Vacation Lock for Additional Security 1 Open the wall station’s cover to access the Programming FLIP THE LARGE COVER UP TO ACCESS Buttons. Press the LOCK ( ) button to prevent remote PROGRAMMING BUTTONS. controls from opening the door after the door is completely closed.
Page 5: Testing The Safety Beam
TESTING THE SAFETY BEAM WARNING • Photo beams MUST be installed on the garage door to prevent serious injury or death. • This required safety reversing sensor MUST NOT be disabled at any time. • Photo beams should be installed no higher than 6” above the floor. The safety beam has two components, a sender and a receiver.
Page 6: Adjusting The Open And Close Limits
ADJUSTING THE OPEN AND CLOSE LIMITS The limit settings control how far the door will open or CAUTION close. The limits should be set so the door opens even Set the open and close limits carefully. Setting with door opening, and closes at the floor level. the limits beyond the distance that the door can travel could cause damage to the door, the If required, use the following steps to adjust the limits.
Page 7: Automatic Door Force Setup
AUTOMATIC DOOR FORCE SETUP – normally not used The opener automatically measures the door force throughout the entire travel of the door each time the opener cycles. The opener will automatically adjust to changing door hardware conditions over time due to weather and wear.
Page 8: Programming Remote Controls
PROGRAMMING REMOTE CONTROLS The opener is supplied with a three-button remote control (the second and third buttons can be used to control additional openers or gates). Additional single and multi-button remote controls can be purchased. The short wire on the back of the opener serves as an antenna for the remote controls. Do not cut off the wire or the remote controls will not operate well.
Page 9: Programming Keypad Codes
PROGRAMMING WIRELESS KEYPAD CODES The optional Linear wireless keypad is designed for use with automatic garage door and gate openers. To Add or Remove a Wireless Keypad Code 1 Press the opener’s LEARN button. The ADDING OR REMOVING A KEYPAD opener’s light and red light will flash once and turn on for about 15 seconds.
Page 10: Setting Up The Wall Station
SETTING UP THE WiFI WALL STATION This Wall Station allows operation of the light and door using the buttons, and when paired with the Android or iOS application you can operate garage doors, manage your family’s access, controls lights and it informs you of people coming and going, from any location.
Page 11 LINEAR APP Use your smart phone to visit the app store and install the LINEAR application. On initial use you’ll be asked to register and create an account. 4:21 PM CARRIER Once complete, sign in with your new account information. New Account Create a Mighty Mule Account First Name...
Page 12: Maintenance
MAINTENANCE Weather conditions may affect the door operation which could require some re-setting of the opener’s adjustments. Doors may swell and become heavier during wet periods, door hinges and rollers might bind during cold periods. To insure safe operation of the door, perform the following tests, including any additional test steps described.
Page 13: Installing/Replacing The Battery Back-Up
6 Reposition and secure the LED panel. 7 Replace the operator housing and tighten the four (4) screws to secure the housing. * Includes battery box and screws. Sold separately for Ultra 900. ** Battery sold separately for Ultra 900.
Page 14: Troubleshooting
TROUBLESHOOTING Flash/Beep Problem Cause Remedy Trouble Code Remote control entered No Problem Add any additional remote controls into memory Check wall station wires. Be sure both are connected to the Door won’t operate Shorted wall station wires terminal screws. Check for a staple in the wall station wires. Remove any staples compressing the wire.
Page 15: Warranty
This product is warranted to the original consumer against defects in material and workmanship for the periods mentioned above. Precision Door Service, LLC will repair, or at its option, replace, any device that it ﬁnds requires service under this warranty. This warranty does not apply to damage to the product from negligence, abuse, abnormal usage, misuse, accidents, normal wear or tear or due to failure to follow Seller’s instructions, or arising from improper...

This manual is also suitable for:

Ultra 900b