Table of Contents
Advertisement
5. Panic
Alarming
6. Car-Jacking
Alarming
7. Car Locator
6 Chirps
E. ACTIVE ARMING – LOCK & ARM:
button
1. Press
on the transmitter.
2.
The siren will chirp once and parking light will flash once indicating that the system is now armed. The vehicle's
doors will lock upon arming if interfaced with the security system.
DEFECTIVE SENSOR REMINDER: If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar.
SILENT ARMING / DISARMING: Press the transmitter
security system, No chirp sound will be heard, arm / disarm confirmation will be through the vehicles parking lights
only.
SENSOR BY-PASS:
The sensor bypass feature is programmed to activate for one arming cycle only. The security system will
return to normal operation during the next arming cycle.
Sensor By-Pass : Press
times within 5 seconds will arm the security system and by-pass the sensor (shock sensor).
HIDDEN ALARM FUNCTION:
Press
button while
the
button to activate the hidden alarm function. The security system will arm and with "Hidden Alarm
Function" The siren / horn will be silenced even if the sensor is triggered in the armed status.
indication will only appear on the LCD.
F. PASSIVE ARMING
Active arming / disarming is controlled by your security system via the remote transmitter. This security system is
equipped with an optional Passive Arming feature, which allows the security system to arm 30 seconds after the last
door is closed. Operation is as follows.
1. Turn the ignition to the "OFF" position and exit the vehicle.
2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you reopen any door / hood /
trunk, the security system LED will stop flashing. It will begin flashing again once all vehicle entrances are closed.
3. After 30-second timer has elapsed, the security system will automatically "ARM". The siren will chirp [1] time and the
parking lights will flash [1] time.
PASSIVE ARMING WITH PASSIVE DOOR LOCKING
The vehicle doors will automatically lock after the passive arming cycle has been completed.
PASSIVE ARMING BY-PASS: While the system is disarmed, Press the
with [1] chirp and LED will turn "ON". The security system will remain in this temporary state for as long as you wish.
To exit passive by-pass, press the transmitter
G. ACTIVE DISARMING – UNLOCK & DISARM:
1. Press
button on the transmitter.
2. The siren will chirp twice and the parking lights will flash twice indicating that the security system is now disarmed.
The vehicle's doors will unlock and the dome light will turn on for 30 seconds upon disarming. (Note: Power door
locks and dome light must be installed with the security system.)
TAMPER DISARMING: If the alarm is triggered upon disarm, the system's siren will chirp 4 times, and the parking
lights will flash 3 times.
PATHWAY ILLUMINATION: When receiving an unlock /disarm signal, this feature will turn the parking lights "ON" for
30 seconds and for 10 seconds upon the lock signal.
TWO STEPS DOOR UNLOCK: This feature will independently unlock the driver's door only when disarming the
security system. Pushing the
AUTOMATIC RE-ARM: If this feature is selected, the security system will automatically re-arm itself in 60 seconds
after disarming with remote transmitter. Automatic rearm will cancel if any door is opened before the 60 seconds timer
has elapsed.
H. DISARMING WITHOUT A TRANSMITTER
OVERRIDES THE ALARM WITHOUT PASSWORD PIN CODE:
(Factory Default Setting)
The Override function may be used if the remote transmitter is lost or inoperative.
1. Enter the vehicle and turn the ignition switch to 'ON' position.
2. (Alarm will sound.)
3. Within 10 seconds push and release the valet switch. The alarm will stop sounding and enter the disarm mode. You
can now start and operate the vehicle normally.
OVERRIDE THE ALARM WITH PASSWORD PIN CODE:
Unlike valet switch easily found, and defeated, this security system allows the consumer to program a password pin
code. Offering a higher level of security.
1. Enter the vehicle and turn the ignition switch to 'ON' position. (Alarm will sound.)
2. Within 5 seconds, enter your chosen first digit code by pressing and releasing the Valet Switch. (When finished
Flashes
Flashes
12 Flashes
button while "PASS " icon flash (see Table 1) or press the
icon flash (see Table 1) or press the
or
button a second time within 3 seconds will unlock the other doors.
Flashes
Disable
Flashes
Locking
and
buttons at the same time will arm or disarm your
button twice, the system will respond
buttons and the system will return to normal status.
6
button first; within 3 seconds press
button two
Alarm
Advertisement
Table of Contents
