Table of Contents
Advertisement
Quick Links
StagePRO KBDS‐01D DJ Stand
Parts List
1
2 Feet
2
1 Leg #2
3
1 Leg #3
4
2 Adjustable Cross Members
5
1 Upper Support Bracket #5
6
1 Upper Support Bracket #6
7
1 Expandable Table
8
1 Velcro Safety Strap
9
2 Optional Mounting Clamps
10
Hardware
A 4 Cross Members Tensioning Knobs
B 2 Expandable Table Tensioning Knobs
C 2 Wing Nuts for Expandable Table Tensioning Knobs
D 4 Screws with Plastic Washers (quantity shipped may vary)
E Foam Cushions
Required Tools
1
Phillips Screw Driver
Step 1
Place Feet on flat surface with raised section facing up.
Place slots in short angled section of Leg #2 over holes in Foot. Long section of Leg #2
should be pointing up with flat surface to the outside.
Place 2 Plastic Washers on 2 Screws and insert Screws through slots on Leg #2 and
into holes on Foot.
The ends of the Foot and Leg #2 should be flush.
Tighten screws
Repeat process for second Foot and Leg #3.
Step 2
Place assemblies in front of you so the long sections of the Feet are facing away
and the back of the DJ Stand is facing you. The long flat sections of the
Legs #2 and #3 should be to the outside.
Ensure both Cross Members are adjusted to the same length.
Place threaded ends of one Adjustable Cross Member in center notch of each Leg.
Attach and tighten a Cross Member Tensioning Knob to the Leg on left side
(this will provide stability for assembly and will be removed in a later step).
Assembly Instructions
Advertisement
Table of Contents
Summary of Contents for StagePro KBDS-01D
- Page 1 StagePRO KBDS‐01D DJ Stand Assembly Instructions Parts List 2 Feet 1 Leg #2 1 Leg #3 2 Adjustable Cross Members 1 Upper Support Bracket #5 1 Upper Support Bracket #6 1 Expandable Table 1 Velcro Safety Strap 2 Optional Mounting Clamps Hardware A 4 Cross Members Tensioning Knobs B 2 Expandable Table Tensioning Knobs C 2 Wing Nuts for Expandable Table Tensioning Knobs D 4 Screws with Plastic Washers (quantity shipped may vary) E Foam Cushions Required Tools Phillips Screw Driver Step 1 Place Feet on flat surface with raised section facing up. Place slots in short angled section of Leg #2 over holes in Foot. Long section of Leg #2 should be pointing up with flat surface to the outside. Place 2 Plastic Washers on 2 Screws and insert Screws through slots on Leg #2 and into holes on Foot. The ends of the Foot and Leg #2 should be flush. Tighten screws Repeat process for second Foot and Leg #3. ...
- Page 2 Step 3 Place the Upper Support Bracket #5 on Leg on right side so that the top of Upper Support Bracket #5 angles in. The threads of the Adjustable Cross Member should be extending through slot of the Upper Support Bracket #5. Rotate the Adjustable Cross Member so its adjustment knob is facing up. Attach a Cross Member Tensioning Knob to Adjustable Cross Member threads and tighten 3 revolutions only. Raise the Upper Support Bracket #5 until slot stops against the thread of knob and then fully tighten knob. Step 4 Place the second Adjustable Cross Member so the threaded ends are resting in top notch of Legs #2 and #3. The threads on right side of the top Adjustable Cross Member should be extending through slot of the Upper Support Bracket #5. The knob in the center of the Adjustable Cross Member should be facing up. Attach and tighten a Cross Member Tensioning Knob to right side of top Adjustable Cross Member. Step 5 Remove Cross Member Tensioning Knob on left side (the first knob attached). Place the Upper Support Bracket #6 on outside of Leg #3 so that the top of the Upper Support Bracket #6 angles to the inside. Attach Cross Member Tensioning Knobs to both Adjustable Cross Members threads on left side and tighten 3 revolutions only. Raise the Upper Support Bracket #6 until slot stops against the threads of bottom Knob; then fully tighten knob. THREADS OF ADJUSTABLE CROSS MEMBERS MUST BE RESTING IN NOTCHES OF LEGS WHEN CROSS MEMBER TENSIONING KNOBS ARE TIGHTENED. Step 6 On left side, insert the Expandable Table Tensioning Knob so threads are resting on Notch (2 from top) of Leg #3 then attach an Expandable Table Wing Nut tightening only three revolutions. Repeat process on right side. ...
- Page 3 Step 8 Separate the Velcro Hook and Loop Safety Strap. Press two inches of Hook onto end of Loop then thread one end through slots on sides of Expandable Table bringing ends together above table to support electronics. Place Foam Bumpers on arms of Support Brackets and Feet as desired. To adjust the width of the DJ Stand, loosen center knobs of Adjustable Cross Members and two knobs on underside of Expandable Table. Adjust width as desired and re‐tighten knobs. Two Optional Mounting Clamps can be used for clamping DJ stand to a table or coffin. To use, remove four screws from Feet and attach Mounting Clamps. ...
Need help?
Do you have a question about the KBDS-01D and is the answer not in the manual?
Questions and answers