Advertisement
Quick Links
\\Ads4\verwaltung\INDUTHERM\Produktunterlagen\Begleitblaetter\WORD\86196800_handling_after_transport_VTC800V_GB.doc 08.07.2016 p 1
Documentation for INDUTHERM no. :
86196800 after transport VTC800V
Thank you for buying our product. Attached is a short installation process,
before you start your serial production.
Before you start:
1.) Please check, if your machine has any damages from the transport.
Inside and outside of the machine is a tilting sensor to detect, if the
machine was tilted (not allowed) the blue liquid will be seen on the tip of
the sensor #84400010
Sensor #84400010
2.) Remove the red transport safety bar T shaped.
Keep the bar after transport!
Attention!
There are two sensors. One outside of the box. Check the
outside sensor while the truck driver is there. One is
inside the machine.
Responsible
INDUTHERM technician:
Klaus Schmidt
ks@indutherm.de
Tel: +49-7203-9218-12
if the machine was tilted
Unscrew and remove the
red plate and the bar!
Remove the 4 screws.
Advertisement
Related Manuals for Indutherm VTC800V
Summary of Contents for Indutherm VTC800V
- Page 1 \\Ads4\verwaltung\INDUTHERM\Produktunterlagen\Begleitblaetter\WORD\86196800_handling_after_transport_VTC800V_GB.doc 08.07.2016 p 1 Responsible INDUTHERM technician: Documentation for INDUTHERM no. : Klaus Schmidt ks@indutherm.de 86196800 after transport VTC800V Tel: +49-7203-9218-12 Thank you for buying our product. Attached is a short installation process, before you start your serial production. Before you start: 1.) Please check, if your machine has any damages from the transport.
- Page 2 \\Ads4\verwaltung\INDUTHERM\Produktunterlagen\Begleitblaetter\WORD\86196800_handling_after_transport_VTC800V_GB.doc 08.07.2016 p 2 3.) Measure the amount of water that comes out of your machine (see last page) Water in (check with manometer if possible the water input pressure, min. 2.5 bars) Water out tube 4.) Adjust feet of the machine, so that the vacuum chamber is exact...
- Page 3 \\Ads4\verwaltung\INDUTHERM\Produktunterlagen\Begleitblaetter\WORD\86196800_handling_after_transport_VTC800V_GB.doc 08.07.2016 p 3 5.) The press plate must be inside the flask holder 6.) Attached is the setup for the machine. The starter kit that comes with the machine is shown inside the manual chapter...
- Page 4 \\Ads4\verwaltung\INDUTHERM\Produktunterlagen\Begleitblaetter\WORD\86196800_handling_after_transport_VTC800V_GB.doc 08.07.2016 p 4 Technical background for fast heating cycles For optimum heating speed the filling of crucible is very important Big nuggets will melt very fast, if the are inside the middle of the coil. So fill in material like described below: a.) Start with 2-3 cm loose drillings or turnings on the crucible bottom...
- Page 5 \\Ads4\verwaltung\INDUTHERM\Produktunterlagen\Begleitblaetter\WORD\86196800_handling_after_transport_VTC800V_GB.doc 08.07.2016 p 5 Place pyrometer (removed for safe transport) back inside the holder. If the machine is on and you press the small yellow button on the pyrometer you see a red laser dot. This dot should view into the centre of the window and the crucible.
- Page 6 \\Ads4\verwaltung\INDUTHERM\Produktunterlagen\Begleitblaetter\WORD\86196800_handling_after_transport_VTC800V_GB.doc 08.07.2016 p 6 10.)To achieve support additional information and support about your machine you are free to sign in into our INDUTHERM web shop 10.) If you use a RCD (Residual Current Device) the RCD might switch to off position. This happens if you plug in the mains plug into the wall.
- Page 7 5.) The pyrometer laser point is right in the centre of the glas [ ] 6.) The melting time of the rod is _ _ _ seconds 7.) INDUTHERM should enable your web shop access with the following e-mail address...