Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Co2meter TecPen MAP
Summary of Contents for Co2meter TecPen MAP
- Page 1 TecPen MAP Oxygen Analyzer User Manual Version 11...
-
Page 2: Table Of Contents
Contents Quick Start Guide ............................3 Perform a measurement ........................3 Introduction ............................... 4 Package Contents ............................. 4 Layout & Controls............................5 Operation ..............................6 Before You Begin ..........................6 Turning the TecPen On ........................6 Taking a Measurement ........................6 Saving a Measurement ........................ -
Page 3: Quick Start Guide
Quick Start Guide Perform a measurement 1. Acclimatize the device to the surrounding temperature (1-2 hours). 2. Press ON/OFF to switch on the TecPen. 3. The PWR LED will light up green. 4. The TecPen will indicate the battery status and oxygen level with ****%. 5. -
Page 4: Introduction
Introduction The TecPen Handheld MAP Sensor is designed to provide fast, accurate measurements of gas concentrations in closed or pierce-able containers. It uses an optical gas sensor with OLED display as well as USB connectivity. This makes it an excellent tool for: ... -
Page 5: Layout & Controls
Layout & Controls 1. Start Device - Press button: start measurement / stop measurement 2. OLED Display 3. PWR (Power) LED - Lights up when the device is switched on 4. BT LED – Lights up when charging and turned on 5. -
Page 6: Operation
Operation IMPORTANT! If the device is taken to a room with a significantly different ambient temperature, an acclimatization period of 1-2 hours is required. Before You Begin The TecPen can be charged with any 5V USB cable and adapter. Full charging takes place in under 2 hours. -
Page 7: Menu Display
Menu Display In normal use the TecPen has 5 screens that can be viewed by pressing and holding the SAVE button. It is not possible to switch through the screens in reverse order. Screen 1 battery level measured value Main screen Temporary: Memory/Log Indicator Indicator for current... -
Page 8: Menu Options
Menu Options In addition to the main screen the TecPen has 6 menu options screens that can be accessed by pressing and holding the SAVE button. Change Data File Format (Recipes) 1. Hold the SAVE button for 2 seconds to access the menu. 2. -
Page 9: Saving Data
Saving Data Default Operation After each measurement is completed and the pump stops running, the currently displayed measured value can be stored in the internal memory of the TecPen by briefly pressing the SAVE button. By default, a new data file is created each day using the date as the file name and the measured oxygen level and a time stamp as data. -
Page 10: Customizing The Output Data File
Customizing the Output Data File The Product_Number, Product_Name and Product_EAN fields can be customized so that multiple Tec Pens can be used and all will have different names in their data files. The TecPen can be further customized by selecting different “recipes” from the menu depending on the job. To get started, you need to modify a file named Rezepte.csv loaded on in TechPen’s internal memory. -
Page 11: Maintenance
If error codes 1, 2, 4 or 5 appear, switch off the device, wait a few moments and then switch it back on. If the same error message appears after switching it back on, contact the manufacturer immediately If the TecPen displays error code 3 during operation turn off the device and contact CO2Meter immediately. -
Page 12: Troubleshooting Guide
**** after a sample oxygen in fresh air (21%). 2 The PWR lights do not light up Does the display show the main screen? after switching on The LED light may be broken, but unless there is an error on the LCD in most cases the device is not charged. The Display shows BATT Battery is uncharged. 3 The Display remains black after Charge the device and try to switch it on again 4 switching it on Did you disconnect your device properly from the Computer the last time? Yes: The battery might be empty. No/ I do not know: Contact CO2Meter. 6 The device is connected to the If the device is switched off while connected to a power power supply, but the BT light outlet, the BT light does not light up while the device is does not light up charging. The device is connected to the You must switch on the device before connecting to the 7 Computer, but I cannot find it computer. If the device is switched on but you cannot find it, check for available COM ports. 8 The measured value is not saved Did you press the LOG button? Did you observe the LOG sign on the display? If yes, contact CO2Meter. 9 The log file shows a wrong date ... -
Page 13: Specifications
Specifications TS‐System TecPen MAP O2 Measurement range 0‐5% Range Accuracy 0‐0.5% ± 2% Mev** 0.5‐2.5% ±3% Mv* 2.5‐5% ±5% Mv* Resolution 0.001% Response time at 25°C/ 77°F <150ms Pump flow max. 67 mL ‐10°C/ +60°C Temp. range Min./Max 14°F/140°F Medium Gas Power supply 5V USB and LiPo battery Rechargeable battery lifetime > 3 hours per charge Data Interface USB 10‐30°C Temperature compensation 50‐86 °F Display OLED Display Cleaning housing no organic solvents. 40% EtOH Parts touching sample St.1.4404/ PTFE/ Glas Case ... -
Page 14: Support
The sensor comes with a 1-year warranty starting from the date it was shipped to the buyer. The TecPen sensor cap comes with a 90 day warranty. For more information visit our website: https://www.co2meter.com/pages/terms-conditions Contact Us If the troubleshooting guide above does not help you solving your problem or for more information, please contact us using the information below.
Need help?
Do you have a question about the TecPen MAP and is the answer not in the manual?
Questions and answers