Download Print this page
Hud-son Oscar 330 Pro Operator's Manual

Hud-son Oscar 330 Pro Operator's Manual

Sawmill

Advertisement

Quick Links

WWW.HUD-SON.COM

Advertisement

loading
Need help?

Need help?

Do you have a question about the Oscar 330 Pro and is the answer not in the manual?

Questions and answers

Summary of Contents for Hud-son Oscar 330 Pro

  • Page 1 WWW.HUD-SON.COM...
  • Page 2 2 ....... . .A note from Hud-Son 3 .
  • Page 3 INTRODUCTION - Purchaser Agreement By accepting the delivery of your sawmill by Hud-Son Forest Equipment you agree that you will not modify your mill from it’s original assembly. This will VOID any warranty from Hud-Son Forest Equipment. Please fill out the information for quick reference: Dealer: ___________________________________________________________ Phone Number: ____________________________________________________...
  • Page 4: Safety Guidelines

    Please use good judgement and keep safety in mind when operating Hud-Son machinery. Please read and follow ALL the instructions in this manual before operating the Hud-Son Mill safely at all times. These instructions were produced for your benefit. Your ability to understand and follow the instructions is essential for the safe operation of this product.
  • Page 5 Hud-Son Forest Equipment is not liable for damage to property or personal injury due to the failure of any person and/or operator to follow the instructions and recommendations set forth in this manual or any other instructions or recommendations contained in other literature issued by other vendor manuals in the owner's kit.
  • Page 6: Unpacking Unit

    2. Move unit to operator's site, lower unit and remove unit from forks. Before operating the Hud-Son Saw Mill the following procedures need to be performed: 1. Check oil and fuel levels washer fluid (usually blue in color) If there 2.
  • Page 7 Steps for Setting-Up the Hud-Son Saw Mill A. Machine Set-Up (ground track unit) 1. For best results and easier set-up, the mill location should be level and free of obstructions. 2. A level cement pad is the best option, but square timbers also work well. You will need to support the track at each joint and under each cross member.
  • Page 8 5. To saw a board accurately, the track needs to be straight and flat. To obtain this, use a string tied tight from end to end or a level. If the track/trailer has a crown or dip, you will not be able to saw a straight board. Correct Track Incorrect Dipped Track...
  • Page 9: Setup And Operation

    Correct head placement; Operators side is on side Squaring arm on right, adjustable dog on left. with the scale stick. Pictured is a close-up of the guide It shows all the bolts and bearings that can possibly be adjusted. Note how the teeth are outside of the guide. Set-Up and Operation E.
  • Page 10 By debarking and cleaning your log it will extend the life of your blade. 1. Adjust the Hud-Son guides so that they are slightly (no more than 2 inches) wider than the maximum width of the log.
  • Page 11 Guide location - log width Debark the log. (Note: as you cut slabs, boards or squares you may need to adjust the guide to ensure the best performance and quality cuts) 2. Find the top of the log with the blade. Remember, that you may have dogs or back stops in place so be sure these are clear when making the first cut.
  • Page 12 Place flat side, flush against squaring pin to Adjustable dog, set at an angle so that log can be ensure a square cant. sawed without interference. H. Cutting Dimensional Lumber You can cut down to a 1" thick bottom board. To achieve this you will use the moveable side of the dog and the short squaring pins welded in the track.
  • Page 13 4. De-tension the band blade after each day of cutting. 5. Never operate the mill without the guards in place. The Hud-Son Forest Equipment, Inc sawmill comes with a band blade and we have an excellent re-sharpening program for your band blade.
  • Page 14 7. Make sure that all nuts and bolts are tightened firmly. N. Using the Lumber Scale 1. All Hud-Son sawmills are equipped with a Lumber Scale. The scale is used to make the dimensioning process simple. The scale incorporates 4 separate scales with the blade kerf factored in for each increment.
  • Page 15 8/4 Scale Row = 2” Actual Blade Height Lumber Used For Scaling 6/4 Scale Row = 1 - 1/2” Lumber Regular Inch Scale 5/4 Scale Row = 1 - 1/4” Lumber 4/4 Scale Row = 1” Lumber...
  • Page 16: Transport Instructions

    1 inch off deck (when the head is completely down). Transport Instructions Follow all the steps to safely transport the Hud-Son Saw Mill Trailer Model 1. Lock head into travel position. 2. Raise extension legs and lock in upright positions.
  • Page 17 Care and Maintenance Hud-Son Saw Mills require a certain amount of care and maintenance, so that it may continue to perform at its best. If you are not confident in your ability to perform the maintenance that is required, please look into having a professional come in and per- form the work for you.
  • Page 18: Maintenance Schedule Chart

    Make sure all nuts are tightened. Check to see any damage that may need to be repaired before further damage occurs. Routinely checking the equipment and proper maintenance will help in keeping the Hud-Son Saw Mill running to the best of its ability.
  • Page 19: Parts And Warranty

    Part Number Warranty See Engine Manufacturer’s Gasoline Engine Manual for Warranty 1 Years - call your servicing Electric Motor Hud-Son Dealer. 6 Years - call your servicing 1.5" Pillow Block Bearing, BEA-01-24 Hud-Son Dealer. BEL-01-24, BEL-02-58-077, 1 Year - call your servicing...
  • Page 20 TUB-20-XXX 2 Years (XXX=LENGTH IN INCHES) 2 Years - call your servicing Bolt for Track Wheel Hud-Son Dealer. 3 Year - call your servicing TE-30/36 Hud-Son Dealer. 1 Year - call your servicing Hud-Son Dealer. WIN-01-2000, WIN-02-2500 1 Years - call your servicing...
  • Page 22 Item No Description Part Number Oscar 236 pro cage weldment MIL-02-236 LIFT TUBE TUB-20-56 OSCAR HEAD WELDMENT MIL-01-236 3/8 ZHN HAR-25-06 1 1/2" Angle Bracket w/Hole SS0012 BATTERY BOX TENSIONER BOLT ASSEMBLY MIL-06-3036 ENGINE MOUNT BRACKET SS0024 LUBE FILL PORT OSC-40034 LUBE PORT OSC-40035...
  • Page 23 GUIDE PIN MIL-10-0000-001 OSCAR 30/36 BLADE GUARD MIL-03-3036-01 DRIVE BELT GUARD MIL-03-3036-03 EXTENSION HANDLE ASSEMBLY MIL-10-3036-003 BRIGGS MUFFLER EXH-01-23H, EXH-01-16H Saw Blade Guard "HUD-SON" MIL-03-3036-02 SITE GLASS ASSEMBLY KIT-001 ADJUSTABLE SCALE STICK MIL-04-3036 MINI-VALVE FIT-03-03-04 BARB FITTING FIT-03-01-04 90 DEGREE PLASTIC FITTING...
  • Page 24 "SIMPLIFIED BLADE GUIDE LHS ASSEMBLY" BLG-02-01 1/2-18 X 4 Z EYEBOLT HAR-09-06-64 1/2 Z FW HAR-50-08-1250-063 1/2 ZSW HAR-56-08-1250-063 1/2-18 X 2 1/4 X 1 1/2 ZHB HAR-02-08-36 1/2-18 X 4 1/2 X 1 1/2 ZHB HAR-02-08-70 ELECTRIC WINCH WIN-02-2500 5/16 Z FW HAR-50-05-875-063 5/16 Z SW...
  • Page 29 OSCAR 330 PRO LIFT CABLE INSTALLATION INSTRUCTIONS Your Oscar 330 Pro Saw Mill comes with a manual winch lift system. This system is spooled with a 5/32" steel cable that is used in combination with the winch to lift and lower the saw mill cutting head. The pictures below will help you in the event you need to re-install a cable.
  • Page 31 Item No Part No Description 071025BE BLACK EPA FUEL TANK HOU0279 TANK STRAP UCP205-10B 1" PILLOW BLOCK BEARING LIFT BALE-330 OSCAR 30 CABLE LIFT TUBE T2000 Brake Winch 1500 F-93392 3/8 Z FW F-59758 3/8 ZHNN 976-026 WINCH SHOULDER BOLT F-93480 3/8 Z SW F-58952...
  • Page 32 GUIDE PIN DH-1053-B OSCAR 30/36 BLADE GUARD DH-1052 DRIVE BELT GUARD O30-005-01 EXTENSION HANDLE ASSEMBLY 80796516HP BRIGGS MUFFLER DH-2500 Saw Blade Guard "HUD-SON" O36-002-15 ADJUSTABLE SCALE STICK 0427029 MINI-VALVE AP012518SA25N BARB FITTING AP03518MFE518N 90 DEGREE PLASTIC FITTING F-42927 1/2-18 X 2 1/2 ZHB...
  • Page 33 44075 KEY SWITCH TUB-20-50 LIFT TUBE MIL-07-3036 LUBE TANK MIL-02-330 OSCAR 30 CAGE F-42800 1/4-20 X 1/2 ZHB F-58010 ZERK FITTING SIMPLIFIED BLADE GUIDE 976-072 LHS ASSEMBLY SK-1-1/2 Q BUSHING BOLT 976-006 1/2-18 X 4 Z EYEBOLT F-94854 Cable, 5/32 HOS-02-04-21 LUBE HOSE CC-1/8...
  • Page 37 4. If the problem is deemed to severe to be fixed in the field by the customer, then the customer must bring the saw mill, at the owner's expense, to the closest Hud-Son Dealer/Distributor for repair. If the Dealer/Distributor is not qualified to make the repairs, then the equipment must be returned to Hud-Son Forest Equipment, Inc at the customer's expense.
  • Page 38 ALWAYS CALL YOUR SERVICING DEALER FIRST!! Dealers/Distributors carry parts and are very knowledgeable with the inner workings of your sawmill. Remember that modifying your mill or using parts that are Not Hud-Son Forest Equipment Inc approved, can void your warranty.
  • Page 40 Thank you for choosing We have an onsite technician available to answer any questions...

This manual is also suitable for:

Oscar 336 pro