Advertisement
Table of Contents
- 1 Table of Contents
- 2 Safety Care
- 3 Specification
- 4 Each Part Description
- 5 Reparations before Use
- 6 Pairing
- 7 Single Operation Mode
- 8 Functions of Throttle Lever and Reverse Lever
- 9 Method of Adjustment of Output
- 10 Accessories
- 11 Buzzer Sounds and Led Lighting Patterns
- 12 Troubleshooting
- Download this manual
Battery system wrenches with built-in angle sensor
Instruction Manual
Thank you for purchasing YOKOTA
Before use, please read this Instruction Manual carefully and use the product
properly after fully understanding the Manual.
Please be sure to keep this Instruction Manual.
YOKOTA INDUSTRIAL CO., LTD
Head Office/Factory
5-55 Nishiiwata 3-chome, Higashiosaka City, 578-0947 Osaka, Japan
TEL.: +81-6-6788-1381
YS-e Instruction Manual 76-QD0444EN-00Y01-00.doc
YS-e600
YS-e800
YS-e900
YS-e950
FAX. +81-6-6781-4519
http://www.yokota-kogyo.co.jp
1
products.
Advertisement
Table of Contents
Related Manuals for Yokota YS-e600
Summary of Contents for Yokota YS-e600
- Page 1 YS-e600 YS-e800 YS-e900 YS-e950 Instruction Manual Thank you for purchasing YOKOTA products. Before use, please read this Instruction Manual carefully and use the product properly after fully understanding the Manual. Please be sure to keep this Instruction Manual. YOKOTA INDUSTRIAL CO., LTD...
-
Page 2: Table Of Contents
YS-e Instruction Manual 76-QD0444EN-00Y01-00.doc Table of contents SAFETY CARE ........................3 SPECIFICATION ........................10 EACH PART DESCRIPTION ....................12 REPARATIONS BEFORE USE ..................... 14 PAIRING ..........................15 SINGLE OPERATION MODE ....................17 FUNCTIONS OF THROTTLE LEVER AND REVERSE LEVER ..........18 METHOD OF ADJUSTMENT OF OUTPUT ................ -
Page 3: Safety Care
・In cases where you lost this Instruction Manual or the warning label affixed to the product or made it dirty, immediately contact us or your YOKOTA representative to obtain the Manual or the warning label, and then properly retain the Manual or replace the warning label. - Page 4 YS-e Instruction Manual 76-QD0444EN-00Y01-00.doc ・ 【Noise might be regulated under laws and regulations of the country or regions where the product is used.】 The tool must be used at noise levels below those prescribed by them. Install sound insulation walls, depending on the necessity.
- Page 5 YS-e Instruction Manual 76-QD0444EN-00Y01-00.doc ・If you do not use the product, unplug the battery charger. Wipe out dust or stain accumulated on the power plug or receptacle with a dry cloth. Failure to do so may result in electric shock or fire. ・Do not insert or remove the power plug of the battery charger from the receptacle with wet hand.
- Page 6 Note that unsecure installation may cause damage on the attachment and/or early malfunction of the product as well as accidents. ・Use socket stoppers specified by Yokota or socket makers. Do not use wire, a nail and others as a substitute for a socket stopper, which can cause serious accidents.
- Page 7 ・If you feel uneasiness during the use, stop using the tool immediately and ask repair and inspection to YOKOTA or YOKOTA-authorized or designated servicing factory via the sales outlet or sales representative. If any accident or problem occurs due to the customer’s intended action such as disassembly of this product, we shall not be liable for such trouble.
- Page 8 Do not use the chlorinated solvent, gasoline, thinners and the like, which work to melt the plastic. ・Ask repair and inspection to YOKOTA or YOKOTA-authorized or designated servicing factory via the sales outlet or sales representative where you bought the product. If any accident or problem occurs due to the customer’s intended action such as disassembly of this product, we shall not be liable for such...
- Page 9 1.6. Other Cautions Caution ・Use protector only specified by YOKOTA for prevention of wounds. ・Do not touch the oil plug of the tool except repairing. It causes early oil leakage. ・Using a tool which has been in storage for more than 6 months may cause oil leakage because of damage to the seal part on the impulse mechanism.
-
Page 10: Specification
YS-e Instruction Manual 76-QD0444EN-00Y01-00.doc 2. Specification ・Tool Model YS-e600 YS-e600A YS-e800 YS-e800A YS-e900 YS-e950 Suitable size of screw M6～M8 M6～M8 M8～M10 Torque adjustment range (*1) 7 to 20Nm 5 to 18Nm 15 to 35Nm 10 to 30Nm 30 to 50Nm 40 to 60Nm incl. - Page 11 YS-e Instruction Manual 76-QD0444EN-00Y01-00.doc ・Battery Pack Model BPL-1820 Nominal voltage Rated capacity 2.0Ah External dimensions 76mm(W) × 119mm (D) × 45mm(H) Weight 0.41kg Ambient operating temperature 0～40℃ ・Battery Charger Model BC0075G Rated input voltage AC100～240V±10% 50/60Hz Rated charging current External dimensions 200mm(W) ×...
-
Page 12: Each Part Description
YS-e Instruction Manual 76-QD0444EN-00Y01-00.doc 3. Each part description ⑧ ⑦ ・Tool ③ ④ ⑥ ⑤ ② ① ⑨ Lever to start or stop the rotation of the main shaft of the tool. ① Throttle lever Lever to switch the rotation direction (right/left) of the main shaft of ②... - Page 13 YS-e Instruction Manual 76-QD0444EN-00Y01-00.doc ① ・Battery Pack ② ④ ③ ⑤ ① Terminal part Terminal for connection with the tool. Air intake for cooling the inside of the battery pack during charging. ② Ventilation opening When PUSH button is pressed, the LED(s) light up and indicate the ③...
-
Page 14: Reparations Before Use
YS-e Instruction Manual 76-QD0444EN-00Y01-00.doc 4. reparations before use Since the battery pack you purchased is not fully charged, fully charge it before use. 4.1. Before charging Place the battery charger in a location at 0 to 40℃. The cooling fan in the charger operates or stops depending on the temperature of the battery pack. -
Page 15: Pairing
YS-e Instruction Manual 76-QD0444EN-00Y01-00.doc 5. Pairing To operate the tool, pairing with the wireless unit (initial connecting action) is required. After turning on the wireless unit, carry out pairing according to the following steps. 5.1. Install the battery pack to the tool. 5.2. - Page 16 YS-e Instruction Manual 76-QD0444EN-00Y01-00.doc 5.6. Press the pairing button of the tool. Press the button with the flat face of TF pin 2 x 90 until it beeps and the LED of the tool blinks fast in yellow. *Do not continue to press the pairing button after the buzzer beep and fast blinking of the LED.
-
Page 17: Single Operation Mode
YS-e Instruction Manual 76-QD0444EN-00Y01-00.doc 6. Single operation mode The tool can be operated alone by the following steps. *In single operation mode, the tool does not shut off automatically. The set values cannot be changed and all data such as tightening results, tightening waveforms are not stored. -
Page 18: Functions Of Throttle Lever And Reverse Lever
YS-e Instruction Manual 76-QD0444EN-00Y01-00.doc 7. Functions of throttle lever and reverse lever Throttle lever When the throttle lever is pulled after insertion of RIght the battery pack or during SLEEP status, the tool is activated. When the throttle lever is pulled again after the tool is activated, the main shaft of the tool Left rotates. -
Page 19: Accessories
YS-e Instruction Manual 76-QD0444EN-00Y01-00.doc 9. Accessories Item When mounted Protector *1 For YS-e600: White For YS-e800: Blue For YS-e900: Black At installation TF pin 2×90 *1 *1: For protector and TF pin 2×90, use the parts specified by us. -
Page 20: Buzzer Sounds And Led Lighting Patterns
YS-e Instruction Manual 76-QD0444EN-00Y01-00.doc Buzzer sounds and LED lighting patterns Buzzer sound Condition LED lighting pattern pattern When the tool is activated Repeating OFF - orange ON - orange OFF (slow (pairing is not done or WU-1 is The buzzer beeps blinking) OFF after pairing is done) When the tool is activated... - Page 21 YS-e Instruction Manual 76-QD0444EN-00Y01-00.doc State LED lighting pattern Battery pack Repeating blueON and OFF ・・・ Remaining amount Warning-Alarm warning (Restore to the Purple rapid flashing former state or Motor return to the Overheat alarm ・・・ former state Rapid flashing of purple and white Driver after the Overheat alarm...
-
Page 22: Troubleshooting
YS-e Instruction Manual 76-QD0444EN-00Y01-00.doc Troubleshooting Before asking repair, carry out the following checks. If the trouble cannot be solved by the following actions, or if other trouble occurs, stop using this product immediately, and be sure to ask us or our qualified (designated) servicing factory via your sales outlet or sales agent. - Page 23 YS-e Instruction Manual 76-QD0444EN-00Y01-00.doc When the throttle lever is released during no-load Operating sound of the brake when stopping. It is not a trouble. Continue the use. rotation, you hear a stop sound. Abnormal temperature Use the tool having proper tightening capability The load on the tool is big.