Advertisement
TI02-134ENG-REV4
SIRCHIE
Products • Vehicles • training
Catalog Nos. FPT-Series and PFT-Series (all inclusive)
INTRODUCTION
Use these instructions for assembly of all SIRCHIE fingerprint
benches. Note: Inspect all cartons for damage. If damage is found,
contact the delivery carrier immediately.
Carefully unpack the carton(s) and check for all parts against the list
at the end of these instructions to insure that you have everything
needed for assembly. If a part is found to be missing, please contact
the factory for prompt service. Assembly should be done on a clean,
soft cloth or other nonabrasive surface.
PROCEDURE
For All Bench Assemblies
1. Assemble divider insert to center divider with four 6-32 x 1/4"
pan head screws (Fig. 1).
Ph: (919) 554-2244, (800) 356-7311 • Fax: (919) 554-2266, (800) 899-8181 • Web: www.sirchie.com • Email: sirchieinfo@sirchie.com
®
TECHNICAL INFORMATION
Fingerprint Bench Assembly
100 HUNTER PLACE, YOUNGSVILLE, NC 27596 USA
1 of 8
Copyright© 2011 by SIRCHIE
All Rights Reserved.
SFL1009
Divider Insert
SFL1008
SFL225
Center
Divider
FIGURE 1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for SIRCHIE FPT-Series
- Page 1 1. Assemble divider insert to center divider with four 6-32 x 1/4" pan head screws (Fig. 1). FIGURE 1 100 HUNTER PLACE, YOUNGSVILLE, NC 27596 USA Ph: (919) 554-2244, (800) 356-7311 • Fax: (919) 554-2266, (800) 899-8181 • Web: www.sirchie.com • Email: sirchieinfo@sirchie.com 1 of 8...
- Page 2 TI02-134ENG-REV4 2. Assemble center divider as- sembly to bottom with three 6-32 x 1/4" pan head screws (Fig. 2). SFL1008 Center 3. Lay the top upside down on Divider the work surface. Attach the end caps with two 6-32 x SFL1007 3/8"...
- Page 3 TI02-134ENG-REV4 SFL121 SFL118 SFL1011 Assembled End/Right SFL1006 Bottom SFL1010 Subassembly End/Left SFL100 End Cap SFL1001 SFL1001 FIGURE 3 For Column Mount Benches (FPT400S, FPT400SPIP, FPT500S, FPT500SPIP, FPT200P, FPT200PPF, FPT200PCM, FPT300P, FPT300PPF, FPT300PCM) Note: The column must be assembled prior to the next step. Refer to the bench pedestal assembly in- structions on Page 5.
- Page 4 TI02-134ENG-REV4 SFL2091 SFL1002 SFL225 SFL225 Assembled Bench SFL1000 SFL225 Assembled Bench SFL225 SFL225 Wall Mount Option FIGURE 4a Assembled Column SFL115 SFL115 FIGURE 4b SFL2146 *When ordering a Top Subassembly, you MUST include the Model Number of your fingerprint bench. 4b.
- Page 5 TI02-134ENG-REV4 BENCH PEDESTAL ASSEMBLY INSTRUCTIONS Note: Check for damage upon receipt of Fingerprint Bench Pedestal and report any to delivering carrier. Open all boxes and carefully remove contents. Check against list on back page for all necessary parts to construct the base. If any parts are missing, contact the factory for prompt service. 1.
- Page 6 TI02-134ENG-REV4 FIGURE C—Secure rods through bottom of base. FIGURE B—Attach mounting plate to column. 6 of 8...
- Page 7 TI02-134ENG-REV4 FPT274A, FPT274PIP, FPT275A, FPT400S, FPT400SPIP, FPT500S, BENCH PEDESTAL CONTENTS: FPT275APIP, PFT100A, PFT100APF, FPT500SPIP, FPT200P, FPT200PPF, 1- SFL136 Base PFT100ACM, PFT200A, PFT200APF, FPT200PCM, FPT300P, FPT300PPF, 1- SFL828 Column PFT200ACM CONTENTS: FPT300PCM CONTENTS: 1- SFL2160 Column Mount 1- SFL? Top Sub-Assembly* 1- SFL? Top Sub-Assembly* 2- SFL829 Threaded Rods 1- SFL1006 Bottom 1- SFL1006 Bottom 4- SFL176 3/8" Lock Washer 1- SFL1007 Back 1- SFL1007 Back 2- SFL174 3/8"-16 Hex Nut 1- SFL1008 Center Divider 1- SFL1008 Center Divider 2- SFL173 3/8"-16 Acorn Nut 1- SFL1009 Divider Insert 1- SFL1009 Divider Insert...
- Page 8 TI02-134ENG-REV4 SIRCHIE ® PRODUCTS • VEHICLES • TRAINING 100 Hunter Place, Youngsville, nc 27596 usa 919-554-2244 • 800-356-7311 www.sirchie.com 8 of 8...
Need help?
Do you have a question about the FPT-Series and is the answer not in the manual?
Questions and answers