Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Purkeys SafeFreight
- Page 1 DELIVERY TRUCK ALARM INSTALLATION GUIDE 300-6 Doc 3.01...
-
Page 3: Table Of Contents
12 Volt Power and Buzzer Installation .............7 Main Harness/Sensor Power Routing ..............8 Key Switch Installation ..................9 Key Switch/Door Sensor Wiring ..............10 Door Limit Switch ....................11 LED Alarm Logic .....................12 Part List ......................15 Limited Commercial Warranty Policy ............19 P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net... -
Page 4: General Information
GENERAL INFORMATION The Purkeys SafeFreight delivery truck alarm system provides an audible alarm if the roll-up door on a vehicle is opened without authorization. -
Page 5: Diagram
SAFEFREIGHT INSTALLATION GUIDE DIAGRAM P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net... -
Page 6: Module Installation
MODULE INSTALLATION Step 1: Locate a spot behind the driver seat to mount the control module. Step 2: Use mounting screws to fasten the module to the truck. Installation Complete. MAIN HARNESS ROUTING Step 1: Lift up the door trim that runs along the driver door. - Page 7 SAFEFREIGHT INSTALLATION GUIDE Step 3: All wires with exception of the LED wires and Ignition wire will travel through the firewall. LED Wires Ignition Wire Harness pushed through firewall grommet already on truck. Installation Complete. P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net...
-
Page 8: Led/Ignition Installation
LED/IGNITION INSTALLATION Step 1: Locate a spot on the dashboard of the vehicle where the driver can see the LED, but not be distracted by it while driving. Drill an appropriate hole to place the LED. Step 2: Plug the LED wires into the connector as shown. -
Page 9: 12 Volt Power And Buzzer Installation
Step 3: Connect the buzzer ground to the truck battery ground and the positive to the main harness (quick connector). Installation Complete. P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net... -
Page 10: Main Harness/Sensor Power Routing
MAIN HARNESS/SENSOR POWER ROUTING Step 1: Take the jacketed two-conductors and connect one end to the truck batteries. Remove fuse from fuse holder until after installion of the door sensor. After doing so, take the conductor and group it with the wires that are left to be routed from the main harness (key switch wires, and door sensor wire). -
Page 11: Key Switch Installation
Step 1: Find a good spot on the side of the truck near the back where the door access key will be installed. Step 2: Drill a hole that the key switch can be mounted through. Step 3: Install the key switch in the hole. Installation Complete. P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net... -
Page 12: Key Switch/Door Sensor Wiring
KEY SWITCH/DOOR SENSOR WIRING Note: All wires have been preterminated to eliminate crimping. Extra terminals have been supplied in case terminals are damaged during wire/ cable routing. Step 1: If wiring was routed from inside of the box of the truck, bring the wiring down to the bottom of the box. -
Page 13: Door Limit Switch
Step 5: Crimp the orange wire from the main harness to the orange wire on the door switch. Crimp the red wire from the black conductor to the red wire on the door switch. Solder and heat shrink each connection. Installation Complete. P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net... -
Page 14: Led Alarm Logic
LED LOGIC... - Page 15 SAFEFREIGHT INSTALLATION GUIDE P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net...
-
Page 17: Part List
Harness, Main for SafeFreight Alarm Sytstem Part # 800-24 Bag Kit, SafeFreight Alarm System Terminal/Connectors Part # 800-25 Harness, Door Sensor Power and Ground Part # 800-26 Assembly, SafeFreight Buzzer with Pigtail Power and Ground P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net... - Page 18 Part # 800-27 Assembly, Keyswitch for SafeFreight Alarm Part # 800-29 Asembly, Dashboard LED for SafeFreight Alarm Part # 800-80 Module, SafeFreight Part # 800-100 Sub Assecbly, SafeFreight Plunger Style Limit Switch w/Wires and Brackets...
- Page 19 SAFEFREIGHT INSTALLATION GUIDE Part # 800-106 Bag Kit, SafeFreight Cable Routing and Mounting Part # 300-6 Guide, Installation, Delivery Truck Alarm System P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net...
- Page 20 NOTES...
-
Page 21: Limited Commercial Warranty Policy
Product or failure of a part not manufactured by Purkeys. This warranty shall not apply if any Purkeys product is used for a purpose for which it is not designed or is in any way altered without the specific prior written consent of Purkeys. ANY... - Page 23 SAFEFREIGHT INSTALLATION GUIDE P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net...
Need help?
Do you have a question about the SafeFreight and is the answer not in the manual?
Questions and answers