Advertisement
Quick Links
Advertisement
Summary of Contents for Mega Pool Saver MPS-1100
- Page 1 MPS-1100 Programming Guide Mega Pool Saver Ltd 1 ...
- Page 2 MPS‐1100 Programming Guide Contents 1. Introduction ................................ 2 2. Manual Mode ................................ 2 3. Backwash Mode ................................ 4 4. Setting System Clock .............................. 5 5. Setting Auto Mode Timers and Speeds ........................ 6 6. Auto Mode ................................ 11 1. Introduction The mps‐1100 has two run modes, manual mode and auto mode. Manual mode is used when you are connecting to a pool chlorinator or timer. The system time settings are not required to run in this mode. Auto mode is used when there is no chlorinator or timer and includes up to 4 separate timers with individual speed options. This is ideal for when you want to run your pool pump at different times and speeds to take advantage of the different electrical tariffs. 2. Manual Mode In off mode press the FUNCTION button once. The display will now show MANUAL, SPEED 1 and the speed in rpm. www.megapoolsaver.co.uk Page 2 of 11 ...
- Page 3 MPS‐1100 Programming Guide Press the up or down buttons to select the speed. Alternatively press one of the systems, preset speed buttons MEGA SAVE, HIGH SAVE, MEDIUM SAVE. Press the ON OFF button to put it into on mode, this will start the pump. When the chlorinator timer turns off, the MPS‐1100 will store the speed and resume at that speed when switched on again. To stop the pump simply press the ON/OFF button again. www.megapoolsaver.co.uk Page 3 of 11 ...
- Page 4 MPS‐1100 Programming Guide 3. Backwash Mode In off mode press the FUNCTION button once. The display will now show MANUAL, SPEED 1 and the speed in rpm. Press the BACKWASH button. The display will now show SPEED 4 and the rpm. Press the ON OFF button to put it into on mode, this will start the pump. Press the ON OFF button to stop the pump. If previously set in manual mode you will need to follow the manual mode instruction to set it again. If previously in Auto mode you will need to put the MPS‐1100 to auto mode all other settings are not affected. www.megapoolsaver.co.uk Page 4 of 11 ...
- Page 5 MPS‐1100 Programming Guide 4. Setting System Clock In off mode press and hold FUNCTION button for five seconds. The display will then show the hour digits flashing. Press the UP or DOWN buttons to select the hours. Press the FUNCTION button to step over to minutes. The display will then flash the minutes digits. www.megapoolsaver.co.uk Page 5 of 11 ...
- Page 6 MPS‐1100 Programming Guide Press the UP or DOWN button to select the minutes. Press the FUNCTION button to store the time. The display will now show the current time with flashing cursor and the word Now shown at the top. Please note if the mps‐1100 loses power the system clock settings will be lost. 5. Setting Auto Mode Timers and Speeds In off mode press the FUNCTION button 3 times. The display should show START, TIMER 1 and the stored time with hours digits flashing. This is the start time for TIMER 1. www.megapoolsaver.co.uk Page 6 of 11 ...
- Page 7 MPS‐1100 Programming Guide Press the up or down button to select the hours. Press the FUNCTION button to step over to minutes. The display will then flash the minutes digits. Press the up or down button to select the minutes. www.megapoolsaver.co.uk Page 7 of 11 ...
- Page 8 MPS‐1100 Programming Guide Press the FUNCTION button to store the time and step to STOP time. The display will now show STOP, TIMER 1 and the stored time with hours digits flashing. This is the stop time for TIMER 1. Press the up or down button to select the hours. Press the FUNCTION button to step over to minutes. The display will then flash the minutes digits. Press the up or down button to select the minutes. www.megapoolsaver.co.uk Page 8 of 11 ...
- Page 9 MPS‐1100 Programming Guide Press the FUNCTION button to store the time and step to SPEED setting. The display will now show SPEED 1‐ 4, TIMER 1 and rpm. This is the speed for TIMER 1. Press the up or down button to change motor speed. Alternatively press one of the systems preset speed buttons MEGA SAVE, HIGH SAVE, MEDIUM SAVE. Press the FUNCTION button to store the speed and step over to TIMER 2. The display will now show TIMER 2, START and the stored time with the hours digits flashing. www.megapoolsaver.co.uk Page 9 of 11 ...
- Page 10 MPS‐1100 Programming Guide Repeat steps above to set speed, start and stop times for TIMER 2 3 and 4. Pressing the FUNCTION button after selecting the speed for TIMER 4 will finalize the timer settings. The display will go blank and return to off mode with the current set time displayed. Alternatively if you only require one time period per day press the FUNCTION button to cycle through time a speed settings of the remaining TIMERS ensuring all start and stop times are set to zero's or to the same time period as TIMER 1+. Please note all settings for TIMER 1 to 4 will be retained in the event of power loss. www.megapoolsaver.co.uk Page 10 of 11 ...
- Page 11 MPS‐1100 Programming Guide 6. Auto Mode After all timers have been set. In off mode press the function key twice. The display will now show AUTO, EVERYDAY and current system time. The MPS‐1100 will then start and stop the pump at set times and speeds. Warning if power is lost system time will need to be set again. The unit will also have to be switched to auto mode. www.megapoolsaver.co.uk Page 11 of 11 ...
Need help?
Do you have a question about the MPS-1100 and is the answer not in the manual?
Questions and answers