Related Manuals for Munch Machine Mother Bucker MB1
Summary of Contents for Munch Machine Mother Bucker MB1
- Page 1 Mother Bucker Model: MB1 Operator’s Manual Please read the operator’s manual and all included warnings carefully and make sure you fully understand the instructions before using the machine 181213...
-
Page 2: Table Of Contents
Table of Contents Warnings & Precautions Introduction Machine overview Operator Safety Training Operation Machine Controls Control Panel (Exterior) Control Panel (Interior) Roller Tension System Applying Roller Tension Removing Roller Tension Hood Hood Removal Hood Installation Direct Contact Surfaces Face Plate Die Plates Catchment System Machine Transport... -
Page 3: Warnings & Precautions
Mother Bucker by Munch Machine. • WARNING – This product is a piece of power equipment that if used in ways other than described by this instruction manual can result in operator injury or even death •... -
Page 4: Introduction
Introduction Thank you for your purchase of the Mother Bucker built by MUNCH Machine. Welcome to the best bucking team around! Our products are designed around years of real-world use and optimized for maximum reliability and durability. Every product we bring to market is designed, tested and manufactured 100% in the USA. -
Page 5: Machine Overview
Machine overview 1. Frame 15. Indicator Light 33. Shaft Coupler 2. Face Plate SS 16. Speed Dial 34. Flex Element 3. Die Plate - Rounds 5 17. Divider Strap 35. Nylon Cover hole 18. Cam Strap 36. 5R Coupler .75” 4. -
Page 7: Operator Safety
Operator Safety Training Operators must be properly trained in the correct use of this machine before taking part in any operation. It is up to the facility to determine guidelines based on these instructions for use. It I sup to the organizations management structure to implement training programs, written procedures, and supervision that are compliant to local regulations. -
Page 8: Machine Controls
Machine Controls Control Panel (Exterior) Power Selector Switch OFF / FWD / REV Mode selection switch allowing the user to turn the machine on (FWD), turn the machine OFF and to reverse (REV) the machine to clear any blockage. Variable speed control Adjusts the Roller revolutions per minute to allow the user to balance throughput and quality. -
Page 9: Control Panel (Interior)
If this breaker continues to trip please contact Munch Machine Customer service team immediately as it may indicate a larger problem. -
Page 10: Roller Tension System
§ ATTENTION – Do not make any adjustments to the tensioning system of the machine, the tension has been preset and will not need adjustment unless otherwise directed by MUNCH Machine. Hood The hood of this machine is designed to protect the user from moving internal parts of the machine, while allowing access for cleaning and maintenance. -
Page 11: Hood Removal
Hood Removal Unplug the machine. Approach from the back side and locate the two thumb screws on the top of the hood. Also locate and note the position of the hood mount pegs, located on the lower left and lower right sides of the hood. Loosen and fully remove the two thumb screws one at a time while supporting the hood with the opposite hand. -
Page 12: Direct Contact Surfaces
Lift the hood keeping the 4 holes upwards and away from your body, the curvature on the back of the hood should be the closest point to your body. Tilting the top edge of the hood slightly forward, align the Roller Tension Bolts with the top 2 holes on the Hood but do not set the hood down on the Force Cap. -
Page 13: Die Plates
The face plate has eight ¼ - 20 holes threaded into it. Four of these holes have a button head bolt installed and serve as a placeholder for accessory options. The other four holes closest to the center cutout are for Die Plate installation. Die Plate §... - Page 14 § WARNING – This machine is capable of pulling body parts, hair, clothing, gloves, etc. into the feed holes of the installed Die Plate. Use extreme caution to prevent unintended items from entering the feed holes of installed Die Plates. Accessory available for purchase Blank Plate This die plate has no feed holes so that you can build a plate that best suits your needs.
-
Page 15: Catchment System
This cam strap is designed to secure bins and buckets around their circumference to the frame of the machine. Conveyors Please reach out to the MUNCH Machine customer service team if you intend to attach a conveyor to your machine. Machine Transport... -
Page 16: Machine Guarding
This machine has two handles built into the frame: one is located on the right side of the machine, and the other is on the left side of the machine wrapping around the lower end of the control panel. Only these two handles and the lower frame are to be used for moving the machine. -
Page 17: Operation
WARNING – Operation of equipment without the proper guarding installed could result in serious injury and possibly death Contact MUNCH Machine Customer Service if you need further assistance. Machine Operation Daily Inspection o Check that the hood is installed properly o Die plate is clean and free of debris. -
Page 18: Daily Shut Down
o Continuously monitor the outfeed of the machine to prevent the stem pile from reaching the height of the upper frame tube. At this point the machine needs to be unplugged and the stem pile needs to be removed from behind the machine. §... -
Page 19: Maintenance
Pressure Washers The entire machine may be washed using water from a hose. The Rollers, Faceplate, Die Plate, and Frame may be cleaned using a high-pressure washer. Do not direct a high- pressure stream at any electrical components, Control Buttons, Motor, Cables or the Bearings. - Page 20 With high wear the green Flex Element should be replaced. One additional Flex Element is included with each machine, and additional Flex Elements can be purchased from MUNCH Machine Customer Service. It is recommended to keep a spare Flex Element on hand at all times.
-
Page 21: Compliance
FCC and ICES Compliance (110V model) The MUNCH MACHINE Mother Bucker, Model MB1-120V has been third party tested and meets the requirements of FCC Part 15 and ICES-003 for Type A unintentional radiators : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. -
Page 22: Storage
A Suppliers Declaration of Conformity may be obtained from the manufacturer. EU Compliance (230V model) The MUNCH MACHINE Mother Bucker, Model MB1-230V is in conformity with the relevant Community harmonization legislation and is CE marked. The EU Declaration of Conformity is provided with the shipping documents, and may be provided upon request. -
Page 23: Technical Specifications
Technical Specifications Machine Dimensions Height 52” 133 cm Width 40” 102 cm Depth 32” 81cm Weight 300 lbs 136 kg Power Requirements 110V Model (US/CAN) Volts / Hz / Circuit / Amp Draw 110V / 60Hz / 15A / +/- 3 Amps 230V Model Volts / Hz / Circuit / Amp Draw 230V / 50Hz / 10A / +/- 3 Amps... -
Page 24: Declaration Of Conformity
Munch Machine Model MB1-230V Serial number 180917-2 The manufacturer: Frazer Industries, LLC doing business as: Munch Machine 160 4th Street West, Suite 1 Ketchum, ID 83340 U.S.A. This declaration of conformity is issued under the sole responsibility of the manufacturer.
Need help?
Do you have a question about the Mother Bucker MB1 and is the answer not in the manual?
Questions and answers