Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for sylber SOL R-7,5M
- Page 1 INSTALLATION AND MAINTENANCE MANUAL SOLAR STATION SOL R - 7,5M...
-
Page 2: Table Of Contents
Thank you again, and keep up the good work, This product must only be used for the purpose Sylber for which it is designed and made, as specified by declines all responsibility, contractual or CONTENTS... -
Page 3: Precautions
GENERAL INFORMATION PRECAUTIONS SAFETY AND CONTROL DEVICES The operation of any appliance that uses electrical power The solar station security is assured by a security valve with demands that a number of fundamental safety precautions intervention pressure of 6 bar. be respected. -
Page 4: System Layout
GENERAL INFORMATION SYSTEM LAYOUT TECHNICAL SPECIFICATIONS return solar DESCRIPTION station Maximum working pressure Maximum operating temper- °C ature Dimensions LxHxP 264x362x215 2 3 4 Net weight with insulation Power supply 230~50 V~Hz Min/max electrical current 0,04 ÷ 0,48 draw Min/Max power consumption 2 ÷... -
Page 5: Installation
INSTALLATION UNPACKING THE PRODUCT 10 ASSEMBLY - Remove the front insulation (1) Package content - Mark mounting points (F) on the wall and drill - Insert blocks (not supplied) 1 Solar Station In a plastic bag, the following material is also supplied: 2 Instruction manual 3 Logo. -
Page 6: Water Connections
INSTALLATION 11 WATER CONNECTIONS 12 PUMP CONTROLLER The circulator is produced with maximum idraulic head configuration of 7,5 meter. USER INTERFACE The user interface consists of a push-button (1), a red/ green LED (2) and four yellow LEDs (3). When necessary, the user interface provides access to: - Functioning (performance display) mode. - Page 7 INSTALLATION Alarm display Direct speed control mode. If the pump detects one or more alarm conditions, LED 1 changes from green to red. When an alarm is active, the LEDs indicate the type of alarm as shown in the following Yel- Yel- Curve 1 (4,5m)
-
Page 8: Electrical Connections
INSTALLATION 13 ELECTRICAL CONNECTIONS - connect the cables as shown in the figure. The following is mandatory: - have an omnipolar magneto-thermal circuit breaker and a disconnecting switch compliant with the pre- PWM CONNECTOR vailing standards of the installation country - respect the polarity of the L1 (Phase) - N (Neutral) connections - use cables with insulation and cross section con-... -
Page 9: Commissioning And Maintenance
COMMISSIONING AND MAINTENANCE 14 SYSTEM FLUSHING PWM input signal With a low input value (<5 % PWM), the pump cannot start. The pump stops when input signal is 5 to 8% of PWM signal Before filling the system with mixture of water and glycol, it or when PWM signal is not present, for safety reasons. -
Page 10: System Filling Cock
COMMISSIONING AND MAINTENANCE If copper piping has been used and joints have been To fill the system, proceed as follows: hot brazed, flush out the system to remove any braz- - Verify the flow-meter (C) is completely open ing residues. Seal test the system after you have - Connect the filling pump (PC) as shown flushed it out. -
Page 11: Device Cleaning And Maintenance
COMMISSIONING AND MAINTENANCE 16 DEVICE CLEANING AND - Disconnect circulator power by removing connectors (D) and (E) MAINTENANCE - Move away any wiring and electric devices below to protect them against any leakage of heat transfer fluid - Close the valve (VR) by turning the handle 90° clock- Service the system at least once a year and carry out wise the inspections specified in the relevant manual. - Page 12 Via Risorgimento, 23 A 23900 - Lecco (LC) www.sylber.it The manufacturer strives to continuously improve all products. Appearance, dimensions, technical specifications, standard equipment and accessories are therefore liable to modification without notice.
Need help?
Do you have a question about the SOL R-7,5M and is the answer not in the manual?
Questions and answers