Advertisement
Quick Links
Fitting instructions for Lynx R & S Fairings
Thank you for purchasing the Lynx fairing
• 1 x Fairing
• 1x Screen
• 2x 35mm thumbscrews threaded into two plastic sliders and Nylock nuts.
• 2x 16mm M6 screws
• 2x 30mm M6 screws
• 2x 30mm M6 Flange bolts
• 2 x plastic washers
• 2 x M6 Flange Nuts
• 2 x 10mm aluminum Spacers
• 1 x Black Aluminum Support Plate
• 1 x Aluminum bottom bracket with threaded bolt, washer and Nylock nut
• 1 x ABS Dash.
• 1 x Wiring Harnes
Removing the OEM parts
• Secure the Motorcycle in a vertical position.
• Remove the seat
• Remove OEM fairing and unplug the headlight terminal
• Unplug the speedo terminal and remove your OEM instrument unit from it's
mounting. You will be re-using the 2 screws and rubber grommets to attach the
instrument to the Lynx Dashboard.
• Unplug and remove the triangular ABS warning light
• Remove the three indicator lights. The small bulbs just pull out of the bottom of the
white section on each indicator housing, but mark them to make sure you know which
light goes into the correct indicator lense.
!
– KTM 690 2019 model on
!
Advertisement
Summary of Contents for Britannia Lynx R
- Page 1 Fitting instructions for Lynx R & S Fairings – KTM 690 2019 model on Thank you for purchasing the Lynx fairing • 1 x Fairing • 1x Screen • 2x 35mm thumbscrews threaded into two plastic sliders and Nylock nuts.
- Page 2 Modifying the OEM Backing plate In order for the Lynx fairing to fit, you will need to carry out some cutting and trimming to the OEM black plastic backing plate. This will not prohibit the OEM headlight from being refitted if required. •...
- Page 3 • Drill an ‘access’ hole’ through the backplate in the ‘hatched’ area as shown in the photo. This hole is used later to access the low beam height adjuster screw. Fitting the bottom bracket The aluminum bottom bracket bolts to the bottom triple clamp in front of the front fender as shown here : •...
- Page 4 Before you fit the dashboard to the motorcycle, it is easier to relocate the three indicator lamps and ABS triangle into the pre drilled holes in the dashboard. Each indicator lamp has a small raised area in the 12 o’clock position on the side of the lens. Use a knife or small file to cut a ‘slot’...
- Page 5 If you have purchased the optional Fuse box and accessory kit, read those separate instructions carefully now, before proceeding further here. You will now have a good idea how the dashboard looks and the most important part of your installation is the fitment of your instruments. Although the dashboard comes pre cut for the re location of the ABS and indicator lights, there are many different configurations open to you to customize your instrumentation as you see fit.
- Page 6 only be used for a low power accessory or you could overload your lighting circuit • Plug the white Hitachi terminal into your OEM headlight terminal Fitting the screen • Fit the screen into the tracks on the front of the fairing inserting a thumbscrew on each side and screw into the black slider on the back of the fairing.
- Page 7 Adjusting the lights High Beam Lynx R and S: The LED is attached to the frame with a bolt on each side ( see photo). To adjust the lamp, you can normally push the top or bottom outer rim of the lamp from the front and it will move a little.
- Page 8 right and make height adjustments using a Philips screwdriver ( see photos) through the access hole you drilled earlier. Turn CLOCKWISE to lower the beam height, ANTI CLOCKWISE to Raise the beam height. LYNX S Low Beam The Lynx S Low beam is adjusted using the thumbscrew at the bottom of the lamp. Turn Clockwise to lower the Beam height...
- Page 9 Application is the same as most decals and is best done by wetting the fairing surface first and then using a squeegy to smooth any air bubbles out. Manufactured by : Britannia Composites Ltd 5084 242...