CFM AIR TIGHT WOOD STOVE Owner's Manual

High efficiency air tight wood stove

Advertisement

HIGH EFFICIENCY
AIR TIGHT WOOD STOVE
IF THIS WOOD BURNING APPLIANCE IS NOT PROPERLY
INSTALLED, A HOUSE FIRE MAY RESULT.
FOR YOUR SAFETY, FOLLOW THE INSTALLATION
DIRECTIONS.
CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT
RESTRICTIONS AND INSTALLATION INSPECTION
REQUIREMENTS IN YOUR AREA.
THIS UNIT IS NOT MOBILE HOME APPROVED.
made in
CANADA
OWNERS MANUAL
CFM Corporation

SAFETY NOTICE

6" FLUE REQUIRED
SAVE THIS MANUAL FOR FUTURE REFERENCE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AIR TIGHT WOOD STOVE and is the answer not in the manual?

Questions and answers

Alvin symms
July 16, 2025

Need to replace fire stone in oven also the size fire stone I need.for all nighter big moe Wood stove

Summary of Contents for CFM AIR TIGHT WOOD STOVE

  • Page 1: Safety Notice

    HIGH EFFICIENCY AIR TIGHT WOOD STOVE SAFETY NOTICE IF THIS WOOD BURNING APPLIANCE IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT. FOR YOUR SAFETY, FOLLOW THE INSTALLATION DIRECTIONS. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION REQUIREMENTS IN YOUR AREA.
  • Page 2: Before Installation Of Your Appliance

    After reading these instructions, if you have any doubt about your ability to complete your installation in a professional like manner you should obtain the services of an installer versed in all aspects as to the correct and safe installation. Do not use temporary makeshift compromises during installation. BEFORE INSTALLATION OF YOUR APPLIANCE 1.
  • Page 3 WHY THE CORRECT FLUE SIZE IS IMPORTANT - 6" Draft is the force which moves air from the appliance up through the chimney. The amount of draft in your chimney depends on the length of the chimney, local geography, nearby obstructions, and other factors. Too much draft may cause excessive temperatures in the appliance.
  • Page 4: Installation

    1. Remove all parts from inside the stove body. 2. Select the proper location for the stove. These appliances must not be installed any closer than the minimum clearance to combustible materials shown in Figure A (on diagram sheet). The stove must be installed on a non combustible surface as shown in Figure A (on diagram sheet).
  • Page 5: Floor Protector

    Installation on a Concrete Floor An appliance mounted on a concrete floor does not require floor protection. Carpeting and any other combustible material shall not cover the Floor Protector. If a combustible surface is applied to the concrete floor, a clearance must be maintained equivalent to the area reserved for the floor protector.
  • Page 6: Operation

    REFER TO CHIMNEY AND CHIMNEY CONNECTOR MANUFACTURER’S INSTRUCTIONS CHIMNEY CONTACT YOUR LOCAL BUILDING AUTHORITY FOR APPROVED METHODS OF INSTALLATION 1. This appliance requires a masonry or pre- manufactured chimney listed to ULC S629 (Canada) and UL103HT (USA) sized correctly. 2. If a masonry chimney is used it is advisable to have your chimney inspected for cracks and check the general condition before you install your unit.
  • Page 7: Building A Fire

    INSTRUCTIONS FOR FIRST BURN - CURING THE STOVE PAINT Your stove has been painted with the highest quality stove paint and has special break-in procedures. The heat generated by the normal operation of the stove, will serve to harden the paint. Ventilate the house during the first three times the stove is used.
  • Page 8: Glass Care

    NEVER USE GASOLINE, GASOLINE-TYPE LANTERN FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR SIMILAR LIQUIDS TO START OR ‘FRESHEN UP’ A FIRE IN THIS HEATER. KEEP ALL SUCH LIQUIDS WELL AWAY FROM THE HEATER WHILE IT IS IN USE. REPLACE GLASS ONLY WITH HIGH TEMPERATURE ROBAX PYROCERAM OF THE PROPER SIZE AND THICKNESS The following use and safety tips should be observed: 1.
  • Page 9: Ash Disposal

    CREOSOTE When wood is burned slowly, it produces tar and other organic vapours. These combine with moisture to form creosote. Creosote vapours condense in the relatively cool chimney flue of a slow-burning fire. As a result, creosote residue accumulates on the flue lining. When ignited, this creosote makes an extremely hot fire.
  • Page 10 HELPFUL HINTS WORTH REPEATING 1) What is the correct way to start a fire? a) You will need small pieces of dry wood (kindling) and paper. Use only newspaper or paper that has not been coated or had unknown materials glued or applied to it. Never use coated (typically advertising flyers) or coloured paper.
  • Page 11 7) Is it normal for soot to cover the glass at the beginning of a fire? Your stove has been built with an air wash system that will help keep the glass clear when the firebox has reached a good operating temperature, and has a good draft. Cold firebox temperature and poor draft cause sooting of the glass.
  • Page 12 Csxruttt IIEAfl[NG This manual describes the installation and operation of the Model F1v1270029 non catalytic wood heater. This heater meets U.S. Environmental ProtectionAgency'semissionlimitsforwoodheaters. ftom 10,370 to 29,301 BTU per hour. "oo",No. FW27oo29 This unit has been tisted by Warnock Hersey Limited to meet or exceed ULC S€27 Canada and UL 1482 U.S.
  • Page 13 Desir€d bum rate Med / Low Med / High High - Performance may vary depending on actual home operating conditionq Be sure to remove the protective plastic coating after installing yourwood heater D E S C R I P T I O N DOOR ASSEMBLY DOOR (NO G|-ASS) 2 &...
  • Page 14 CFM Corporation 2695 Meadowvale Boulevard Mississauga, Ontario L5N 8A3 Canada (800) 668-5323 www.cfmcorp.com Service Note: If you are experiencing difficulties or are dissatisfied with your purchase, please contact CFM at the telephone number listed above prior to returning your grill to the store.

Table of Contents