Summary of Contents for FaceGraph Smart Thermal Detector
- Page 1 Smart Thermal Detector User Manual V1. 1 Smart Thermal Detector User Manual 06/28/2020...
-
Page 2: Table Of Contents
Hardware Overview ........................4 User Interface Overview ......................5 Temperature Screening Procedure ................... 5 Temperature Screening Hints ....................6 Smart Thermal Detector Software Setting ................7 Android related setting ......................9 Local Record Exporting ......................11 Quick Troubleshooting Guide ....................12 Need help? .......................... -
Page 3: Warning And Precaution
Warning and Precaution ○ The operation temperature of Smart Thermal Detector is 10 - 40 ℃ (50 – 104 °F). Using this machine in extreme environment may lead to damage of the machine ○ When Smart Thermal Detector shows elevated temperature (Yellow or Red), adjust the position to measure again / use other thermometer to measure the temperature accurately. -
Page 4: Hardware Overview
Environmental Thermometer Micro-SD Card Slot Optical Sensor USB Port 10.2 inch LED display USB Port NFC Sensor RJ45 LAN Port Power on/off button Smart Thermal Detector User Manual V1.1 Copyright © 2020 FaceGraph All Rights Reserved Page 4 / 14... -
Page 5: User Interface Overview
1. Tap NFC card on the NFC Sensor if you would like to record detection with your personal detection (if applicable) 2. Move your head towards the Smart Thermal Detector until your face covered most area of the human shaped frame of the detection area (around 50 cm distances between forehead and the machine). -
Page 6: Temperature Screening Hints
Users should avoid measuring temperature in the cases below, wait for 20 minutes before measuring the temperature. Situation Effect After intense exercise Measure result will be high After hot bath Measure result will be high Smart Thermal Detector User Manual V1.1 Copyright © 2020 FaceGraph All Rights Reserved Page 6 / 14... -
Page 7: Smart Thermal Detector Software Setting
Measure result will be high/low Smart Thermal Detector Software Setting Connect USB Mouse to the Smart Thermal Detector for detail settings of the software. Consult your IT Administrator before the setting Click the setting icon by moving the mouse cursor with your connected mouse. - Page 8 Enter the CMS web address in order to connect to the cloud platform. This value is usually pre- configured and not necessary to configure. Smart Thermal Detector User Manual V1.1 Copyright © 2020 FaceGraph All Rights Reserved Page 8 / 14...
-
Page 9: Android Related Setting
The Smart Thermal Detector supports connecting to the internet with both WiFi and LAN. Before using the Smart Thermal Detector, it is required to set the internet settings in the Android system. Connect the mouse to Smart Thermal Detector, right click the mouse to exit the Smart Thermal Detector software to go to the Home screen of Android system. - Page 10 In android settings, go into the Volume settings. Adjust the sound volume of the machine. It is not recommended to adjust to higher than 90% volume. Smart Thermal Detector User Manual V1.1 Copyright © 2020 FaceGraph All Rights Reserved Page 10 / 14...
-
Page 11: Local Record Exporting
Local Record Exporting Local record exporting is possible if the smart thermal detector is unable to connect to the internet Insert USB storage device into the USB port of smart thermal detector Press export record icon Select the date for export and USB folder for exporting, then click “Export”... -
Page 12: Quick Troubleshooting Guide
- It should load properly. You will be required to go to the settings page and reconfigure the app, choosing the temp unit, entering the machine ID and pressing activate and updating the cloud server url to http://api.facegraph.com The temperature scanning app didn’t launch when I powered on the Smart Thermal Kiosk If Thermal device starts but the app doesn’t launch, restart the device using the... - Page 13 - Delete the current device and create new “Thermal” device - The last step would be to type the new Device ID into Hanshin Measurer app’s settings and pressing activate Smart Thermal Detector User Manual V1.1 Copyright © 2020 FaceGraph All Rights Reserved...
-
Page 14: Need Help
Need help? Online ticket: http://f-g.io/Help Email: ContactUs@FaceGraph.com Phone: +1 (408) 337-2013 [9 am – 5 pm PST M-F] Smart Thermal Detector User Manual V1.1 Copyright © 2020 FaceGraph All Rights Reserved Page 14 / 14...