Table of Contents Package Contents Before You Begin Hardware Overview Installation Setting Up the G4 Doorbell Sample Wiring Diagrams Specifications Safety Notices Electrical Safety Information Limited Warranty Compliance Declaration of Conformity Online Resources...
Before You Begin The G4 Doorbell Camera is designed to work with Ubiquiti’s new integrated camera management system, UniFi Protect. UniFi Protect is a flexible and powerful IP video surveillance system that can manage UniFi Protect cameras and the UniFi Protect mobile app.
Hardware Overview Camera/Lens 5MP with day/night vision Button Press button to chime doorbell. Status LED The LED will flash during bootup. LED State Status Device is busy; do not power off. Breathing White Initialized, Device not configured. Flashing White System initializing. Steady White Device configured and working.
Installation 1. Turn off the electrical breaker to the existing doorbell. 2. Remove the existing doorbell from its mounted location and disconnect all wires. Using the Angled Mounting Bracket 1. Pull the existing wires through the center opening of the Angled Mounting Bracket.
Page 7
3. Align and place the Flat Mounting Bracket up against the Angled Mounting Bracket and mount them to the wall using the two longer screws from the included screw kit.
Page 8
5. Using a phillips screwdriver, connect the Spade Wire Adapters to the back of the G4 Doorbell. 6. Connect the copper wires to the Spade Wire Adapters by pressing down on the tabs and inserting one wire into each adapter.
Page 9
7. Mount the G4 Doorbell onto the Flat Mounting Bracket. 8. Turn on the electrical breaker to power the G4 Doorbell.
Page 10
Using the Flat Mounting Bracket 1. Pull the existing wires through the center opening of the Flat Mounting Bracket. 2. Secure the Flat Mounting Bracket to the wall using the two shorter screws from the screw kit. If the bracket does not sit flush against the wall, use the included washers to sit between the Flat Mounting Bracket and the wall.
Page 11
3. Using a phillips screwdriver, connect the Spade Wire Adapters to the back of the G4 Doorbell. 4. Connect the copper wires to the Spade Wire Adapters by pressing down on the tabs and inserting one wire into each adapter.
Page 12
5. Mount the G4 Doorbell onto the Flat Mounting Bracket. 6. Turn on the electrical breaker that powers the G4 Doorbell.
Setting Up the G4 Doorbell Download and install the UniFi Protect app to set up and configure the G4 Doorbell. 1. Launch the UniFi Protect app. 2. Click the menu in the upper right and tap Add Camera and select G4 Doorbell. 3.
Sample Wiring Diagrams Installation with Chime Box Chimebox FRONT Chimebox Transformer TRANS 16V~24VAC REAR FRONT Transformer TRANS 16V~24VAC REAR Installation without Chime Box Transformer 16V~24VAC Transformer 16V~24VAC...
Specifications UVC-G4-Doorbell Dimensions 118.3 x 46.8 x 25.8 mm (4.66 x 1.84 x 1.02") Weight 200 g (1.03 lb) Networking Interface Wi-Fi 802.11ac Management Interface UniFi Protect Built-In IR LED Illumination Night Mode IR Cut Filter View Angle 114° (H), 138° (V), 155° (D) Resolution 1600 x 1200 Max.
Safety Notices Read, follow, and keep these instructions. Heed all warnings. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in a location that can be submerged by water. WARNING: Avoid using this product during an electrical storm.
Compliance Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation.
Page 18
ISED Canada CAN ICES-3(B)/NMB-3(B) This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: This device may not cause interference, and This device must accept any interference, including interference that may cause undesired operation of the device. This radio transmitter (IC: 6545A-UVCG4DB) has been approved by ISED Canada.
Page 19
IMPORTANT NOTE: Radiation Exposure Statement: • This equipment complies with radiation exposure limits set forth for an uncontrolled environment. • This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. • This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Page 20
English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
Page 21
Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
2014/35/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedećoj internetskoj adresi: ui.com/compliance Čeština [Czech] UBIQUITI tímto prohlašuje, že toto UVC-G4-Doorbell zařízení, je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnic 2014/53/EU, 2014/30/EU, 2014/35/EU. Úplné znění EU prohlášení o shodě je k dispozici na této internetové adrese: ui.com/compliance...
Page 23
Íslenska [Icelandic] Hér, UBIQUITI, því yfir að þetta UVC-G4-Doorbell tæki er í samræmi við grunnkröfur og önnur viðeigandi ákvæði tilskipana 2014/53/ESB, 2014/30/ESB, 2014/35/ESB. Fullur texti ESB samræmisyfirlýsing er að finna á eftirfarandi netfangi: ui.com/compliance Italiano [Italian] Con la presente, UBIQUITI, dichiara che questo dispositivo UVC-G4-Doorbell, è...