Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Kannad Manuals
  4. Camera Accessories
  5. S185 501 Series
  6. Maintenance manual

Kannad S185 501 Series Maintenance Manual

Hide thumbs
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual
TASK 25-63-06-400-801-A01
1. General
A.
Introduction
(1) This section gives the procedures for the assembly of the equipment. The components are
identified by their "Figure - Item" number in the Illustrated Parts List
63-006-991-010-A01).
(2) Assemble the unit in a clean, dust-free area in accordance with the procedure that follows. Use
good standard workshop practices.
(3) Examine the parts (
B.
Special Instruction
CAUTION:
C.
Tools, Fixtures and Equipment
(1) Special Tools, Fixtures Equipment List
Refer to PAGEBLOCK SPECIAL TOOLS, FIXTURES, EQUIPEMENT AND
D.
Annual Inspection Kit
NOTE:
(1) Annual Inspection Kit Content
Part Number
0141822
O-RING
0123831
CAPSULE,DESICCANT
0145234
SCREW, F HEXALOB. M3x16 A4
0146261
SCREW, F HEXALOB. M3x20A4
0136779
NUT, NYLSTOP M3 A4
0141787
LABEL, SEAL
0145250
LABEL, INSPECTION EES1923
0145251
LABEL, INSPECTION EES1928
(2) Use of the annual inspection kit
NOTE:
© KANNAD 2011
The document reference is online, please check the correspondence between the online documentation and the printed version.
Component Maintenance Manual
P/N S185X501-XX
PAGEBLOCK
BEFORE WORK ON THE ELT, MAKE SURE THAT THE FRONT PANEL SWITCH IS
SET TO "OFF".
the parts of the annual inspection kit are also included in the battery kit P/N S1840510-01.
For this reason, it is not necessary to use an extra annual inspection kit when a battery kit
is used. When a battery kit is used, all the parts must be used excepted two screws and the
label EES1923.
Table 7001 / 25-63-06-992-901 : Annual Inspection Kit Content
KIT PAR NUMBER S1840510-02
The purpose of the annual inspection kit is to replace the necessary parts when the
ELT is opened without battery replacement.
ASSEMBLY
CHECK) before you start the assembly.
DESIGNATION
[only used for AP, AP (ER), AP-H, AP-H (ER)]
[not used for INTEGRA ELTs]
25-63-06
(Refer to Figure 10001 / 25-
CONSUMABLES.
Numbers
1
1
4
2
4
1
1
1
Page 7001
JUN 16/2011

Advertisement

loading

Summary of Contents for Kannad S185 501 Series

  • Page 1 (2) Use of the annual inspection kit NOTE: The purpose of the annual inspection kit is to replace the necessary parts when the ELT is opened without battery replacement. © KANNAD 2011 25-63-06 Page 7001 JUN 16/2011 The document reference is online, please check the correspondence between the online documentation and the printed version.
  • Page 2 (d), "Battery type" (a) and "Battery expiry date" (b) fields; - if it is not the first battery replacement, remove the former Inspection label (1-110) from the lower part of the "Identification / Inspection" label. © KANNAD 2011 25-63-06 Page 7002 JUN 16/2011 The document reference is online, please check the correspondence between the online documentation and the printed version.
  • Page 3 Affix the new label (1-110) on the lower part of the identification / inspection label, in place or above the former label (ELT’s rear panel). Figure 7001 / 25-63-06-991-701-1 BATTERY AND INSPECTION LABEL FILLING © KANNAD 2011 25-63-06 Page 7003 JUN 16/2011...
  • Page 4 Fold and stick the fourth part of the foam onto the rear of the battery pack. This leaf must also cover the end of the first leaf on the right side of the battery pack. Figure 7002 / 25-63-06-991-702-1 PROTECTING THE BATTERY PACK © KANNAD 2011 25-63-06 Page 7004 JUN 16/2011...

  • Page 5: Front Panel Assembly, Installation

    Install the front panel assembly (1-210): Refer to SUBTASK 25-63-06-430-002-A01. Figure 7003 / 25-63-06-991-703-1 FRONT PANEL ASSEMBLY, INSTALLATION © KANNAD 2011 25-63-06 Page 7005 JUN 16/2011 The document reference is online, please check the correspondence between the online documentation and the printed version.
  • Page 6 (e) Affix a new seal label (1-150) onto the upper side of the front panel assembly and the housing. Figure 7004 / 25-63-06-991-704-1 FRONT PANEL ASSEMBLY, INSTALLATION © KANNAD 2011 25-63-06 Page 7006 JUN 16/2011 The document reference is online, please check the correspondence between the online documentation and the printed version.

  • Page 7: Fault Isolation

    (5) Remove the paper protecting the back of the new label. (6) Affix the new label in the correct position. Make sure that it is in position before applying pressure. Press lightly to adhere. © KANNAD 2011 25-63-06 Page 7007 JUN 16/2011 The document reference is online, please check the correspondence between the online documentation and the printed version.
  • Page 8 Component Maintenance Manual P/N S185X501-XX PAGE INTENTIONALLY LEFT BLANK © KANNAD 2011 25-63-06 Page 7008 JUN 16/2011 The document reference is online, please check the correspondence between the online documentation and the printed version.

This manual is also suitable for:

S1840510-02