Subscribe to Our Youtube Channel
Summary of Contents for Cody YBS1705
- Page 1 Product Manual & Warranty Information YBS1705 cody electronics intelligent robot vacuum...
- Page 2 Note your serial number for future reference:...
- Page 3 Thank You Thank you for choosing to buy a Cody Intelligent Robot Vacuum cleaner. It has been made with high quality standards and is guaran- teed for domestic use against manufacturing faults for 12 months from the date of purchase (subject to terms of warranty). If you...
-
Page 4: Table Of Contents
Table of Contents Important Safety Instructions Package Contents & Technical Specifications 2.1 Main unit and accessories 2.2 Product diagram 2.3 Specifications Operating & Programming 3.1 Notes before using the appliance 3.2 Product operation 3.2.1 Preparing the Charging Dock 3.2.2 Activating and Charging the appliance 3.3.3 Clock setting 3.3.4 Starting the appliance 3.3.5 Pausing the appliance... - Page 5 Maintenance 4.1 Dust Bin and Filters 4.2 Main Roller Brush 4.3 Side Brushes 4.4 Other components 4.5 Battery Light Indicator and Sounds 5.1 Light Indicator 5.2 Sounds Troubleshooting Consumer Warranty Information 7.1 What is covered 7.2 What is not covered 7.3 Procedure for making a claim under warranty...
-
Page 6: Important Safety Instructions
Important Safety Instructions When using this product or any electrical appliance, basic precautions should always be followed, including the following: • Read all instructions carefully before using this appliance. • Use only as described in the manual. Only use attachments recommend- ed or sold by the manufacturer. - Page 7 35.The appliance must be used in accordance and get in touch to purchase a replacement with the directions in this Product Manual. Cody Electronics cannot be held liable or re- and avoid a hazard. 22.Do not use the Charging Dock if it is sponsible for any damages or injuries caused damaged.
-
Page 8: Package Contents & Technical Specifications
Package Contents & Technical Specifications 2.1 Main Unit & Accessories Charging Dock Bumper Strip Robot Vacuum Power Adaptor Dust Bin Remote Controller Multi-Purpose Cleaning Tool Side Brush x 3... -
Page 9: Product Diagram
2.2 Product Diagram Robot Vacuum 1. Auto Clean / Power Button 2. Anti-collision Sensors 3. Light Indicator 4. Driving Wheels 5. Anti-drop Sensors 6. Battery Cover 7. Universal Wheel 8. Dust Bin 9. Main Roller Brush 10. WiFi Button 11. Side Brushes 12. - Page 10 2.2 Product Diagram - continued Dust Bin 1. Dust Bin 2. Sponge Filter 3. Dust Bin Cover 4. Dust Bin Bank 5. High Efficiency HEPA filter 6. Seal Ring Remote Controller 1. Auto Clean 2. Schedule button 3. Direction control buttons 4. Return to charger button 5.
-
Page 11: Specifications
2.3 Specifications Robot Vacuum Model YBS1705 Working voltage (V) 14.4 V Rated power (W) 30 W Diameter 345 mm Height 80 mm Charging type Auto / manual Charging time 4 - 6 hours Cleaning modes Auto, Edge, Spot, Intensive, Schedule... -
Page 12: Operating & Programming
Operating & Programming 3.1 Notes before using the appliance Before operating the appliance, take a few moments to survey the area to be cleaned and remove any obstacles. Remove the EVA protective strip Attach the Side Brushes and Bumper before using. Strip. -
Page 13: Product Operation
Furniture with bottom space of less than Add a physical barrier to prevent the 8cm may trap the appliance. If cleaning is appliance from falling off the edge. Make needed, please raise the furniture. sure the barrier is not a trip hazard. Please arrange furniture to prevent the Please keep corridors and other narrow vacuum from being stuck or trapped. -
Page 14: Preparing The Charging Dock
3.2.1 Preparing the Charging Dock Connect the Charging Dock with the Power Adaptor. Place the Charging Dock on a level floor surface against a solid and sturdy wall with the base perpendicular to the ground. Keep immediate area (2 meters in front and 1 meter on both sides) of the charger clear of objects, obstacles and reflective surfaces. -
Page 15: Starting The Appliance
Press the clock icon. Change the time by Press the clock icon again The hour on the screen pressing the direction to set time. will start blinking. buttons. 3.2.4 Starting the appliance With the machine activated, press the Auto Clean / Power Button on the appliance or the Auto button on the Remote Controller. -
Page 16: Cleaning Modes
3.3 Cleaning Modes The appliance has several cleaning modes to choose from to effectively clean different floors. Cleaning modes are selected via the Remote Controller. Make sure the appliance is activated before selecting any modes. Every time you select Auto Clean Mode, the ma- chine will start a new cleaning cycle and attempt to clean all areas again. -
Page 17: Scheduling
Edge Cleaning Mode Return to Charger Mode This mode is good for cleaning the edges and When battery power gets low, the appliance corners of a room. In Edge Cleaning Mode, automatically switches to Return to Charger the appliance cleans along a border (e.g. wall). Mode and returns to the Charging Dock to recharge itself. -
Page 18: Set Intelligent Scheduling
3.4.2 Set Intelligent Scheduling Press the lower bell icon. The appliance will perform cleaning after 24 hours. 3.4.3 Cancel Scheduling Press either Scheduling or Intelligent Scheduling button (bell icon) for 3 seconds. -
Page 19: Maintenance
Maintenance Before performing cleaning and maintenance, power OFF the appliance and unplug the Charging Dock. For optimal performance and prevent malfunction, always empty the Dust Bin, clean the filters, sensors, brushes, Charging Contacts and pins after every use. 4.1 Dust Bin and Filters Press the latch to release Remove the filters. Empty the Dust Bin. the Dust Bin. -
Page 20: Main Roller Brush
4.2 Main Roller Brush Press the side latches to release the Remove the Main Roller Brush and clean cover. thoroughly. Remove any fi bres or hair that are stuck Use the Multi-function Cleaning Tool to on the brush, roller and both sides of the cut off and remove any fi bres or hair brush. -
Page 21: Side Brushes
4.3 Side Brushes Remove the Side Brushes. Remove any fibres or hair that are stuck on the brush. Wipe the Side Brushes and their slots with a clean cloth. 4.4 Other components Use the Multi-function Cleaning Tool to cut off and Gently brush the sensors remove any hair tangled around the Universal Wheel. and Charging Contact. -
Page 22: Battery
4.5 Battery Remove the appliance’s battery if it will not be used for a long time. In case of battery leakage, please remove the battery and wipe the battery slot clean while wearing protective gloves. Dispose of the battery according to local laws and regulations. If battery is fully discharged or not used for a long time, its capacity may decrease and will need to be reactivated. -
Page 23: Light Indicator And Sounds
Light Indicator & Sounds 5.1 Light Indicator Machine Status Light Indicator Charging Purple (glowing) Charging complete Blue (constant) Malfunction Red (blinking) Low battery Red (constant) Clean mode Blue (constant) 5.2 Sounds When the appliance detects a problem and needs your assis- tance, it emits alarm beeps and the Light Indicator flashes RED. -
Page 24: Troubleshooting
Troubleshooting Please use the table to troubleshoot your appliance. Appliance will not charge Possible Causes Solutions The appliance has not made a connection Be sure that the appliance’s Charging with the Charging Dock. Contacts have made a connection with the Charging Dock Pins. You may move the appliance manually to make the connection if necessary. - Page 25 Appliance returns to Charging Dock before it finishes cleaning Possible Causes Solutions When the battery power is low, the appli- This is normal. ance automatically switches to Return to Charger Mode and returns to the Charging Dock. Working time varies according to floor This is normal. surface type, room complexity and selected Cleaning Mode.
- Page 26 6 Troubleshooting - continued Remote Controller is not working Possible Causes Solutions The battery of the Remote Controller Replace with new batteries making sure needs to be replaced. they are installed correctly. The appliance is deactivated (no light on Make sure the appliance is activated and Light Indicator) or the battery is low.
- Page 27 The appliance did not return automatically to the Charging Dock Possible Causes Solutions The appliance covered a very large area Clean small areas at one time. Close doors and completely emptied its battery before to other rooms to ensure the appliance has arriving to the dock.
-
Page 28: Consumer Warranty Information
7.2 What is not covered Replacement parts are not covered by the warranty (unless faulty). Cody Electronics shall not be liable for costs of repair or replacement of a... -
Page 29: Procedure For Making A Claim Under Warranty
Should you need to make a claim under this warranty, please visit our website or email us directly at support@codyelectronics.com. Please retain your original invoice as proof of purchase and provide us with the serial number of your appliance. Cody Electronics www.codyelectronics.com hello@codyelectronics.com PO Box 48 Flemington VIC 3031 Australia...
Need help?
Do you have a question about the YBS1705 and is the answer not in the manual?
Questions and answers