Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Champ Craft Play Sets Manuals
  4. Play Sets & Playground Equipment
  5. Childhood Treasure 4250
  6. Assembly instructions manual

Champ Craft Play Sets Childhood Treasure 4250 Assembly Instructions Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
#4250 Childhood Treasure
Assembly Instructions

Advertisement

loading

Summary of Contents for Champ Craft Play Sets Childhood Treasure 4250

  • Page 1 #4250 Childhood Treasure Assembly Instructions...

  • Page 2: Tools Required For Installation

    Tools Required for Installation These are the tools that are required for the assembly of your play set. Most of these tools are not included with the purchase of your play set. (24” Level) (Tape Measure) (Square) (7/16” Socket (Cordless Drill) (2lb Hammer) (Phillips Head Screw Driver) &...

  • Page 3: Parts Identification

    Parts Identification (Wood Components—NOT TO SCALE) “Place all Parts in numerical order when identifying” #1– 46” 2x4 Quantity -11 #2– 46” 5/4 Quantity -10 #3– 91” 3x4 Quantity -4 ( screwed post) #4– 49” 2x4 Quantity - 4 (2 with rope holes and 2 without rope holes) #5–...
  • Page 4 Parts Identification (Wood Components—NOT TO SCALE) “Place all Parts in numerical order when identifying” #17– 24” 1x4 Quantity –2 #18– 112” Quantity—1 (screwed beam) #19– 88” 2x4 Quantity –2 #20– 84” 2x4 Quantity - 1 #21– 69 1/2” 2x4 Quantity - 2 #22–...
  • Page 5 Parts Identification (Not to Scale) 1 Trapeze Bar 2 Sling Swings 1 Steering Wheel 1 Telescope 1 Set Of Hand Grips 2—10’ Ropes 4 Rock Holds 1—6’ Rope...
  • Page 6 Step #1 Identify two part #3’s, measure from the bottom and mark 47¼” and 77” on each post using a pencil & speed square. Step #2 Identify one Part #1, fasten at 47¼” with 4 - 2¼” screws. Two per end. 47¼”...
  • Page 7 Step #3 Identify one part #2, fasten at the bottom of the posts with 4 - 2¼” screws (two per end). Square the post with part #2 as pictured Total Hardware: 4 - 2¼”screws...
  • Page 8 Step #4 Identify one part #1, fasten at 77” with 4 - 2¼” screws. Two per end. 77” Make sure to square all the pieces with the speed square. Repeat steps #1 through #4 This will create a second section exactly like the one pictured above. Total Hardware: 4 - 2¼”screws...
  • Page 9 Step #5 Identify one part #6, center on Part #1 boards and fasten with 4 - 1½” Screws (two per end) (You Must pre - drill the part #6s with a 5/32” drill bit) Part#1 Section #1 Total Hardware: 4 - 1½”screws...
  • Page 10 Step #6 Identify four part #6’s, fasten the first board 2½” from the end of Part #1 as shown. Then space them 3” apart from there. Fasten with 4 - 1½” screws per board (two per end) (You must pre - drill all the part #6s with a 5/32” drill bit) 2½”...
  • Page 11 Step #7 Stand up section #1 place part #2 at the bottom securely fasten with 2 - 2¼” screws Section #1 Total Hardware: 2 - 2¼”screws...
  • Page 12 Step #8 Fasten part #13 to opposite bottom side of section #1 with 2 - 2¼” screws. 19” Part #13 must extend 19” beyond the Total Hardware: outside edge of the post of section #1. 2 - 2¼”screws...
  • Page 13 Step #9 Stand up section #2 and fasten part #13 and part #2 using 2 - 2¼” screws per board. 19” Total Hardware: 4 - 2¼”screws...
  • Page 14 Step #10 Fasten board #1 to section #1 and section #2 with 4 - 2¼” screws, as pictured Repeat step #10 on the opposite side of the tower as pic- tured here. Total Hardware: 4 - 2¼”screws...
  • Page 15 Step #11 Fasten board #1 to center of section #1 and section #2 with 4 - 2¼” screws, as pictured Pre - drill slat with a 5/32” drill bit before fastening part #1. Be sure to counter sink the screws so that they have a proper hold on the part #1.
  • Page 16 Step #12 Fasten board #1 to the side of section #1 and section #2, 47 “ from the floor with 4 - 2¼” screws, as pictured. Step #13 Lay floor boards (two part #12’s and seven part #2’s). Space them evenly as pictured.
  • Page 17 Step #14 Fasten board #1 to the side of section #1 and section #2, 47” from the bottom of the posts with 4 - 2¼” screws, as pictured. Step #15 Now fasten each floor board with 6 - 1½” screws per board. Pre - drill Part #12’s with a 5/32”...
  • Page 18 Step #16 Fasten one part #1 to section #1 and section #2. Make it even with the top of the part #1 2x4 as shown. Fasten with 4 - 2¼” screws per board (two per end). Repeat step #16 on the opposite side. Step #17 Identify part #7 and part #8.
  • Page 19 Step #18 Fasten the Swing Beam Attachment Block, that was assembled in step 17, to the center of the part #1 2x4s as pictured with 4 - 2¼” screws per board. 2½” The Swing Beam Attachment Block must be fastened on the side with part #13 at the base.
  • Page 20 Step #19 Fasten four part #5’s (two on each side of the Attachment Block). Space them as pictured below starting in the center. Fasten them with 4 - 1½” screws per board. Pre - drill with 5/32” drill bit before fastening. 3”...
  • Page 21 Step #20 Fasten six part #5’s to the side of the tower opposite the Swing Beam Attachment Block using 4 - 1½” screws per board. See bottom picture for spacing. Pre - drill with 5/32” drill bit before fastening. 3” 3”...
  • Page 22 Step #21 Assemble the Canopy Frame Trusses. Fasten together as shown with 4 - 1⅛” screws per board (two per end) Pre - drill with a 5/32” drill bit before fastening. 16” 16” Part #16 Part #16 Part #17 10” 10”...
  • Page 23 Step #22 Fasten both trusses to the outside of the tower As Pictured with 4 - 2¼” screws per truss. On the side with the Swing Beam Attachment Block fasten the truss to the swing beam attachment uprights with 4 - 1½” screws. 12”...
  • Page 24 Step #23 Fasten three part #14’s to the trusses as pictured with 4 - 2¼” screws per board. Pre - drill with a 5/32” drill bit before fastening. Total Hardware: 12 - 2¼”screws...
  • Page 25 Step #24 Fasten the Canopy at each end as pictured below with 14 - 1⅛” screws. Total Hardware: 14 - 1⅛”screws...
  • Page 26 Step #25 Build the Ladder. Fasten two part #4’s (without rope holes) and two Part #10’s with 8 - 2¼” screws. The boards must all be square before fastening. See picture below for placement the #10 pieces. 3” 5¼” Pre - drill with a 5/32” drill bit before fastening. Space five part #10’s as pictured and fasten with 4 - 2¼”...
  • Page 27 Step #26 Fasten the Ladder to the tower. Position the Ladder against the tower as shown below. Fasten two metal brackets with 4 -1” pan head screws per bracket. Then fasten at the bottom to part #13 with 2 - 2¼” screws. Total Hardware: 2 - 2¼”screws 8 - 1”...
  • Page 28 Fasten Rock Holds as pictured with 2—1½” bolts with washer and lock nut. ( look at pattern on step 27) Pre-drill with ¼” drill bit Place a washer on each bolt then put the bolts through the rock and the rock climb.
  • Page 29 Step #27 Fasten rock in the pattern pictured below. Tie a 10’ rope securely to the part #1 2x4 above the rock climb. Put knots in the rope as needed and attach to the bottom part #10. Total Hardware: 8 - 1½” Bolts 8 - Washers 8 - ¼”...
  • Page 30 Step #28 Assemble the Cargo Net frame with two part #4’s (with rope holes) and two part #11’s (with rope holes) square each corner and fasten with 2 - 2¼” screws Feed a 10’ rope through the holes in the part #4’s, pull tight and tie securely. Feed the 6’...
  • Page 31 Step #29 Fasten the Cargo Net to the Tower. Fasten the two metal brackets with 4 - 1” pan head screws per bracket. Next fasten at the bottom to part #13 with 2 - 2¼” screws. Total Hardware: 2 - 2¼”screws 8 - 1”...
  • Page 32 Step #30 Attach Toys Attach the Steering Wheel with the included lag and washer using a 9/16th socket. Pre - drill with 5/32” drill bit before fastening. Attach the Handgrips. Attach one Handgrip on the post by the Ladder and one on the post by the Cargo Net with 2 lags in each handle.
  • Page 33 Congratulations you have finished the Tower. This is how it should be looking.
  • Page 34 Step #31 Attach the slide according to the slide instructions that are included with the slide.
  • Page 36 Step #33 Assemble the Swing Beam Upright 6½” Identify four part #23’s and two part #19’s Fasten each part #23 between the part #19’s with 4 - 2¼” screws per board. Use the measurements shown below and to the right. 32”...
  • Page 37 Step #34 Fasten the center of part #20 to the bottom of the beam upright with 4—2¼” screws Step #35 Fasten 2 part #21s with 3—2¼” screws each (1 at the top and 2 at the bottom) as shown. Predrill with a 5/32” drill bit . Part #21 Part #21 Total Hardware:...
  • Page 38 Step #36 Fasten the Beam to the Beam Upright. With 3—2¼” screws per side (6 total). Fasten Part #22 with 3—2¼” screws as pictured. Toenail this screw through Part #22 into Part #19. Predrill with a 5/32” drill bit before fastening. Repeat on the opposite side.
  • Page 39 Step #37 Insert the beam into the attachment block. The beam must be level. Fasten it to the tower with 3—2¼” screws per side (6 total). Total Hardware: 6 - 2¼”screws...
  • Page 40 Step #38 Stake the Set Anchor the Swing Beam Upright with two stakes (one at each end as shown). Drive the stake into the ground leaving 2”-3” above the ground. Fasten with 4—2¼” screws (2 in each stake). Anchor the Tower with two stakes (one on each side of the tower as shown).
  • Page 41 Install Sling Swings Connect the chain and swing seat with the quick link as pictured then tighten with a pliers. Repeat this process on both sides.
  • Page 42 Install Trapeze Bar Attach one end of a chain to the S hook Squeeze shut with pliers Rubber end must touch the bar as shown Finished...
  • Page 43 Step #39 Install Swings As Pictured...